CTV4808DVD / AEG [TV/video/DVD combination]

• Reduced horizontal size.
• Black screen.
• No tuning but tuning bar moves.
• Black screen. 3 horizontal coloured lines in upper part of screen. Sound OK.
• Horizontal line. in the centre.
• Dead. Standby LED does not light.
• No picture. No OSD. Retrace lines. Coloured lines. Excessive brightness. (CTV4808DVD tips)
• Grey screen. Audio OK .
• Vertical dash at center of screen.
• No functions. LED is green. Ticking noise.
• Adjustment values in service menu. (CTV4808DVD tips)
• E/W fault.
• Picture is uniformly uncoloured. Correct colours available only at lower picture edge. (CTV4808DVD AEG repair tip)
• No start-up from standby. LED blinks .
• Enter service mode.
• Intermittently, picture size increasing.
• No picture only red, green and blue lines.
• Tic-tic noise from PSU.
• Contrast drift depending on the picture content.
• Coloured lines. (AEG - CTV4808DVD information)
• Blue raster. Picture in AV mode OK. (CTV4808DVD tips)
• Buzzing noise in standby.
• Flickering picture. Squealing from PSU.
• Blank raster.
• No start-up. intermittently. Slow start-up.
• No RC functions.
• Ticking noise. Standby LED flashes .
• Contrast oscillates depending on picture content.
• No vertical deflection.
• No function, no LED. PSU tries to start. Rattles quickly.
• Annoying noise from PSU in standby.
• White lines in upper third at start, then coloured lines. Sound OK. (CTV4808DVD tip from AEG)
• Dark picture.
• Bright picture. Flyback lines. Shuts down.
• Stuck in standby. Red LED blinks.
• Stuck in standby.
• No image, only test lines approx. 5 cm below upper screen edge, when G2 turned upwards.
• Intermittent jitter in the picture. Horizontal linearity changes.
• Line tearing.
• No audio. No picture.
• No colour.
• Vertical foldover at bottom.
• Switches to standby and red LED flashes after start-up with RC.
• No power supply. Hiccuping power supply. Green LED lit OK.
• Dead. Standby LED flashes .
• Snow in picture.
• No start-up from standby with RC.
• Black horizontal stripes on right picture edge.
• Coloured lines. on upper half screen.
• No start-up.
• PSU switches on for a short time. (CTV4808DVD tips)
• Dead. Tripping.
• No start-up. Standby LED flashes green.
• Tripping.
• No TXT. Shows the page number and a black screen.
• Standby lamp flashes, if appliance starts. LED off.
• No start-up. LED turns green, then appliance switches back to standby
• Picture quivers horizontally.
• No picture. Audio OK .
• Picture jitters and sound is a little bit noisy. Only for 16:9 films.
• Dead. LED is green.
• No start-up from standby.
• Noisy PSU after start-up. Standby OK.
• Dim picture.
• Slow start-up. Pulsating picture. Switches off by itself.
• Bang and noise in picture.
• Excessive horizontal size. Pincushion distortion.
• No function. LED flickers quickly.
• No front panel function.
• Low brightness. Audio OK .
• No start-up. Red LED blinks.
• No functions.
• No functions. via SCART.
• E/W fault. intermittently.
• E-W error. Picture width is too great. Fault occurs occasionally when banging.
• Blank raster. OSD OK .
• Switches to standby. after start-up. (CTV4808DVD tip from AEG)
• Trips. after a few seconds.
• Switches to protection mode. intermittently.
• Excessive horizontal size.
• Green flickers at start up or switches off Red LED OK. No other function. (CTV4808DVD tip from AEG)
• Stuck in standby. Standby LED flashes .
• Vertical line.
• Peeping power supply.
• White screen. Flyback lines. Audio OK .
• Annoying noise from PSU. Functions OK.
• No functions. LED blinks .