7669851710 IS7040VTSAT / BLAUPUNKT [TV 70-74 (66-70) cm picture]

• No picture (intermittently).
• Picture is too dark or jitters at SAT (it becomes brighter and darker). (7669851710 tips)
• Adjustment of bridge L573 coil.
• RC IR DATA PROGRAMMER IDP1 or IDP2: automatic programming mode "HP".
• Picture width changes according to the picture content. Occasionally switches to stand-by, or "AH3" displayed.
• Switches off and sometimes switches on automatically. No standby LED.
• Switching off the two-digit programme sites (10-29, 10-49, 10-99 depending on the individual set). Switchover using the numeric buttons will therefore become quicker. Two-digit programme sites can still be chosen with rocker switch.
• After activating the mains switch or the remote control the appliance starts for a short time and then switches into standby. Appliance only functions if the remote control is pressed until the picture is present.
• Switches off. Display shows AH3. Intermittently red snow in picture.
• Shuts down. after start-up.
• No start-up (when cold).
• Colour processing adjustment only for multi-standard version.
• Station identification display is constant instead of temporary.
• No picture. Audio OK .
• Line begins to flash after approx. 5 mins.
• Station name - (station contraction -) OSD: without/a short time after each programme change/permanent.
• In SAT range picture is distorted, audio fails.
• Horizontal sync adjustment.
• Programming a set using the programmer HTP89.
• Intermittently switches off. Dark display. LED in display is dark. No control via RC, OK via user control.
• Switches off by itself (intermittently).
• Setting of automatic standby time is lost after 10 mins without a signal. Function has to be reset after every start up.
• In PIP to change small picture position in the corners and frame.
• Blue picture with blue flyback lines.
• No functions. Display OK .
• Intermittent picture and sound. Screen is bright without picture content. (7669851710 tips)
• Color processing adjustment.
• No start-up from standby with RC. No shutdown with RC. Other functions OK .
• Changing over to the differing French cable channel raster.
• Enter service mode.
• To make flashing disappear while switching over channel when programming from 1 to 9.
• No brightness. Audio OK .
• Entry of mean values (brightness, contrast etc.).
• Loud crackle when turning on and turns itself immediately off.
• Line phase adjustment.
• Logo displayed for a short time when changing channels, display is constant, display fault.
• No audio.
• No audio. Picture OK .
• When the set is connected to a cable TV-system, and certain channels cannot be received at all or only with a poor quality, probably the wrong channel grid has been set.
• Switches on only when RC is pressed for longer.
• Moire pattern. only on certain channels.
• RV delayed AGC voltage - Tuner.
• Volume too low. No menu and no channel input (station adjustment) possible.
• Adaptation of band-1 CCIR channel (+6.5MHz sound) of a reception in band 1 of a channel with L standards (-6.5MHz sound carrier).
• Appliance should go into "AV" ("1 AV") position at switch on.
• Display appears for a short while after turning on, then it turns itself off.
• Switches to protection mode. (picture attached)
• Memory loss. Cannot be programmed.
• Very bright, nearly white picture with flyback lines at switch on and switches after a short time by itself to standby.
• No picture, no sound. Display, control unit and RC is faultless. It look as if device was switched on AV. On AV also no picture, just sound.
• SECAM bell filter alignment.
• Sound missing and picture is black and white on individual program sites.
• No functions. Poor display.
• If volume is increased or decreased via RC appliance starts to change over programs. (7669851710 BLAUPUNKT repair tip)
• Stuck in standby.
• Automatic programming (HP) for dealers with the IR autoprogrammer FZ900G1.
• Switches automatically to program site AV instead of program site 1 after switch on.
• Intermittently lines in lower picture edge. (depends on picture content).
• No horizontal synchronisation.
• Channel names appear continuously or not at all.
• No picture. No sound. Display shows "AH30".
• Intermittently unfocused picture. Focus cannot be adjusted. (BLAUPUNKT - 7669851710 information)
• No colour. (BLAUPUNKT - 7669851710 information)
• In a cable system appliance should receive a French band I channel (audio carrier -6.5MHz), which is converted into a CCIR Band I channel (audio carrier +6.5MHz).
• Station name indicator constantly displayed. Disappears when switching channels but then immediately reappears.
• Failure of tuners and reduction in reception quality after 2 or 3 years.
• Satellite part fails.
• Dead. (part of circuit diagram displayed)
• No colour. after a while.
• Can be switched only to one AV input (though appliance has 3 AV inputs).
• White balance adjustment.
• Goes into protective switching; line output stage leaky; overheats after replacement. (+ extract of circuit diagram)
• Single digit channel display from 1-9.
• Lines in picture. at top.
• Intermittently switches off with crackle and switches to AH3.
• Bright picture. No picture content. Lateral colour striation. Sound present.
• Switching off the snooze function for repair purposes (appliance switches off after approx 10 mins, after closedown or when no signal is present).
• Cut-off adjustment.
• No HV (after warm-up).
• Digital adjustment of line frequency and line phase on multistandard and on multistandard adapted models.
• No picture, no sound. Pumping noises coming from the appliance. (7669851710 tips)
• Start up in "AV", (1AV).
• Line output stage fails.
• Colour processing adjustment feed in a PAL test pattern.
• Input of averages at memory loss of analogue values.
• No picture. via RF output. AV OK .
• SAT operation defective. No picture and sound only colour shadows in the background.