2616 / BUSH [TV]

• System voltage is too low. It can be controlled but can not be adjusted to required value.
• Bright picture.
• Picture width becomes smaller and moves to left and has narrow strip of picture in left side.
• No picture. Audio OK .
• Power supply unit pulsing.
• PSU pulsates. Dead. after a while.
• Distorted picture approx. 2" wide, on left hand side of screen.
• Blank, narrow raster.
• Transistor (BU508AF) fails.
• No line drive.
• Ticks quietly.
• Stripes in picture. White value pumps. (2616 tips)
• Attempts to start-up. LED flashes.
• Sometimes no switch on. If it does, lines over the whole picture which disappear after a short time.
• Intermittent picture. Odd colours.
• Attempts to start. Makes hissing noise then raster appears with low width. (2616 BUSH repair tip)
• Picture on the left is only approx. 5cm wide with light line tearing. Rest of the screen is blanked.
• No tuning.
• No OSD.
• Noise in audio. at low volume. (2616 BUSH repair tip)
• Odd colour.
• Vertical fault. Horizontal stripe.
• Appears to start but it doesn't have HT.
• No deflection. Standby LED is lit.
• Blows fuse. intermittently.
• Switches on intermittently (three times out of four).
• No functions. Standby LED lit . (2616 tip from BUSH)
• White screen. Flyback lines.
• No vertical deflection.
• No VHF channels. No UHF channels.
• Instability using SCART input.
• Screen grid voltage adjustment.
• Activate combination lock.
• No start-up from standby.
• PSU interferes with channel 2.
• No green.
• Model release/pricing information.
• Vertical collapse. (2616 tips)
• Trips. after start-up.
• No picture. Bright raster. Audio OK .
• Tripping. Burning smell.
• Excessive vertical size.
• Reduced horizontal size. No focus.
• AGC adjustment.
• Blank raster.
• Hum bar.
• One colour missing.
• Dead. Output from power supply appears to be tripping. (2616 tip from BUSH)
• Blocked in standby. Cannot be started from front control on the appliance, nor from RC.
• No RC functions.
• TR301 fails. (service info for BUSH -2616)
• Stuck in standby. (2616 BUSH repair tip)
• Dead. Standby LED lit .
• Flyback lines.
• Trips. Slight hum bar if HT increased. No video.
• No start-up.
• Does not switch on. If program + key is pressed, standby LED blinks. (2616 BUSH repair tip)
• Unlocking combination lock. (2616 tips)
• No TXT.
• Blank screen. No audio. Raster OK .
• Lack of width plus foldover.
• Bright FB lines.
• Vision demodulator adjustment.
• No tuning. OSD OK . Blank screen.
• Dead.
• Bright raster. Audio OK .
• No functions.
• Unfocused 6 inch wide band down screen only. (service info for BUSH -2616)
• No picture. TXT OK .
• No audio. No picture. (2616 BUSH repair tip)
• TXT does not have luminance and has desaturated colours. Contrast is reduced to minimum in MIX mode.
• Excessive brightness.
• Field output.
• Programs disappear after a while.
• Intermittent greyscale.
• Bright green screen at switch on; fades to blank. Sound OK.
• Sporadically lines in picture and noises like HV flashovers.
• Low HT. Standby light flashes.
• No synchronisation.
• Blank raster. Horizontal lines. at top.
• Horizontal line.
• Horizontal jitter.
• No or low video voltage.
• Intermittent PSU failure.
• Greyscale varies.
• Deleting continuous functions. (2616 tip from BUSH)
• Unstable picture when viewing pre-recorded videos.
• Appliance does not switch on. LED reacts when pressing a key.
• LED flashes. Attempts to start up with slight chirping.
• Green picture. Retrace lines. (service info for BUSH -2616)
• Audio pulses on and off ever half second.
• White screen. Flyback lines. Shuts down.
• Dark screen. No display. No picture.
• Bright green raster with flyback lines.
• No blue. Yellow prevailing on screen.
• Dead. LED blinks . (2616 BUSH repair tip)
• Enter service mode.
• Green, red or blue background.
• Line output transistor S/C.
• Dead. Power LED lit .
• Bright flyback lines, bright screen, sound OK. (service info for BUSH -2616)
• Tuning drifts. Snow in picture.
• Line sharpness adjustment.
• No blue.