 |
C14M08 / DANSAI [TV]
The EURAS repair tip database for professional technicians and service engineers
supplies the following faults for C14M08 / DANSAI.
List of fault symptoms:
- Flyback transformer is defective. (C14M08 DANSAI repair tip)
- Picture size increases and decreases.
- No function. Standby is not lit.
- No start-up. Relay clicks .
- Intermittently no colour, field foldover and loss of horizontal shift.
- Intermittent colour. after warm-up.
- Crackling noise.
- Picture jitters at the top and bottom and lines after 30 mins.
- No reception. (C14M08 tips)
- No colour. Snow in picture. (DANSAI - C14M08 information)
- No picture. Audio OK .
- Line output transistor (2SD1541) has blown.
- No functions.
- Enter service mode.
- No colour.
- Stuck in standby.
- Slow start-up. in standby.
- Supply voltage adjustment. (with circuit diagram extract)
- No picture. OSD OK .
- Flyback lines.
- No colour. Reduced vertical size.
- White balance adjustment.
- Retrace lines. Excessive brightness.
- Cracking noise 4-5 times when switched on.
- Poor picture. Low contrast.
- Trips when switched on. (C14M08 tip from DANSAI)
- No channels. No picture, only snow.
- Snowy picture, no channel LEDS and no volume.
- Dark and bright streaking to the right in the picture, also during AV mode and menu displays.
- No functions with RC, only the internet functions.
- Does not shut down.
- Horizontal line.
- Dead.
- OSD shifts or wrong colours when changing channels with RC.
- RC code HQ.
- Coloured lines. at top.
- No picture, only high tension.
- Noise or click from PSU. No start-up. (C14M08 tip from DANSAI)
- No line oscillation.
- Short non-linear frame (may improve as set warms up).
- No colour; lines; jumping - worse on bright scenes.
- No horizontal synchronisation.
- TV stuck on standard BG or DK. Cannot switch to L.
- Vertical collapse.
- Distorted audio. at high volume.
- Two bright lines approx 0,40 inches at lower and upper part of screen.
- Linearity coil humming.
- Only starts on remote.
- Blank raster.
- No RC functions.
- Distorted audio from central speaker.
- Hum bar.
- Screen adjustments.
- Vertical fault. at top.
- IC304 (TDA7263M) fails repeatedly.
- No signal. No picture, only snow.
- No TXT.
- HT does not function.
- No front control operation or LED. Snowy raster. No tuning.
- Defective menu, no OSD.
- No start-up (intermittently).
- Dark screen. Audio OK .
- Horizontal dark lines in centre of screen.
- Intermittent low gain.
- Yellow picture.
- Dim picture.
- Brightness varies.
- AGC adjustment. (part of circuit diagram displayed)
- LED lights, no function.
- Arcing effect on high brightness.
- No picture.
- Wow in audio.
- Picture darkens then goes back to normal.
- Horizontal lines at top 3-4 inches.
- Does not switch to standby.
- No start-up.
- No EE or PB picture. (C14M08 tip from DANSAI)
- Skips channels during tuning.
- Comes on for a short time. Switches to standby.
- No E/W correction.
- Black screen.
- Flyback transformer slightly chirps.
- HV falshover at line transformer.
- Dead. after lightning strike.
- Blank raster. Audio and OSD OK .
- Black streak in lower part and half a picture in upper part of the screen.
- Switches off by itself. at high volume. (DANSAI - C14M08 information)
- Geometry adjustment.
- Flyback lines. intermittently.
- R528 (10K) and C524 (220nF) keeps failing.
- Excessive vertical size.
- No function, goes to standby, red LED is on. Does not start up with RC.
- PSU defective. (C14M08 tip from DANSAI)
- Horizontal output transistor fails repeatedly.
- No picture. Audio OK . No HV.
- Distorted audio (only on certain channels).
- White screen. Flyback lines.
- Weak contrast. (C14M08 tip from DANSAI)
- Noise in audio (intermittently).
- Picture remain visible in standby, but without colours, contrast, or brightness.
- Blank raster. No audio.
Tips are coming from EURAS customers, workshops and payed technicians from all over the world. DANSAI C14M08 fails can be better solved. If DANSAI C14M08 fails, this information will help you. Here you can only see the symptom list, to access remedies, you must register. With help of this list a solution is found often when DANSAI C14M08 fails.
|
Additionally to repairtips or service information C14M08 is linked to 21 components (IC's and/or transformers) in the Tectra
database, through which you can identify electrical compatibilities (crossreferences) in
appliances.
|
Chassis information is available (which chassis is built in into C14M08 ).
EURAS system also knows 470 appliances having the same chassis as C14M08 and can easily list them.
In the repair discussion pinboard for C14M08 there are 48 replies to questions asked about 25 different repair problems. With access to EURAS you can all read them or enter your own questions and get help for C14M08 from EURAS technicians or other users.
Do want to see this remedies/cures for repairtips? Register here for the EURAS System
Already registered? open C14M08 DANSAI in EURAS
All details on the EURAS System: English |
Deutsch |
Français |
Italiano |
Español |
Magyarul |
Português |
Polski |
Română |
Greek |
Back to EURAS Homepage >>
All manufacturers >>
DANSAI
tech tips
(C) EURAS International Ltd.
Last updated: 07. Sep 2008 13:10:52 MET, doccode ISO9002AS168EKA200805C EURASMOP
Responsible for the content: EURAS International GmbH, Eime, Germany.
All rights reserved, EURAS database V2.0 (C) 2002-2008.
All brand- or productnames are copyrighted by the respective manufacturer of the appliance and are only being used for identification purposes.
|
|