991931011171 FSR871CVC2082DAS / FIMI [20" monitors]

• Failure of V801.
• If the monitor goes into Low-Power mode it can no longer be put back into normal mode. It works again if the mains is switched on and off.
• Occasionally picture pumps for approx. 1cm.
• Code number information (2).
• Code number correction.
• Occasionally colour temperature change (knock sensitive).
• Flashing display. (991931011171 FIMI repair tip)
• No high voltage. No deflection. Switch power supply pumps as a result of a S/C.
• After approx 5 mins operating time, picture disappears after switching from Dos to Windows (task). "High Voltage Failure" appears in the display.
• Different versions of the HV box.
• Replacement for transistor V806 MOTOROLA P8P25 on the deflection board.
• Smoke from PSU and type of diode V614/V12.
• Picture disappears shortly (intermittent).
• Occasionally appliance switches to standby because self test warns of a vertical fault.
• Spare part information (1). (991931011171 tips)
• Picture disappears after some time. No error message in the display.
• Appliance goes into breaker circuit operation (short circuit protection).
• Test software.
• Does not synchronise well.
• No digital display. Raster and controls ok.
• Switches off after several hours.
• Horizontal width.
• Picture jitter. Smell from appliance after warming up.
• Takes a long time for the picture to appear.
• Blurred.
• Fine, approx. 1cm wide, dark line which is vertical in the picture and which moves through the picture. (991931011171 tip from FIMI)
• Adjustment via software. Interface is not necessary, cable is sufficient.
• Variations in brightness over the whole picture area.
• The picture is de-focussed in low frequency VGA-modes. (991931011171 tips)
• Starts normally, then "high volt error" appears in the display.
• Error message: 'V Sync OFF' (only temporary) then 'H DEFL.Failure', no more functions.
• No picture. Vertical error in the display.
• No display - all supply-LEDs are on. (991931011171 tips)
• Bad horizontal sync. When using datapath harlequin graphic card.
• Picture dark, no picture tube drive.
• After a short time high voltage failure. Beam current varies.
• H-linearity is shrunk on the right.
• High voltage adjustment.
• No picture.
• No text on LCD display.
• Updated software.
• Failure of V823-V829-V830 (short circuit and damage of P.W. board).
• Technical data.
• One of the three line pre-power and output stage transistors (V830, V829) has exploded.
• Checking the high voltage part.
• Picture has a green cast with green flyback lines.
• Horizontal size varies. Burning smell.
• Picture gets brighter and brigher until there are flyback lines - after an extended operating time (30-45 min.)
• No vertical synchronisation.
• Appliance pumps, no picture. Occasionally at starting up "V out of range" and "Gen Failure" visible in the display.
• Interface cable.
• High voltage fails.
• Demagnetises several times at switch on and otherwise by itself. (991931011171 tips)
• Picture is blurred (very wide vertical lines), resolution perfectly adjustable but still variations in brightness. (fault occurs on BJ95/21" appliances).
• HV EHT adjustment.
• Error mesage: Vertical out of range.
• Switches constantly from normal picture size to a small picture, significant E/W fault, picture becomes extremely bright, front keys do not work. Fault arose when focus control was adjusted.
• Error message "V-Sync OFF" (only for a short time) then "H DEFL.Failure". No further functions.
• No start up, displays 'sync missing', 'high voltage fault' or "PLL error".
• HV setting.
• Squeaking noise.
• Picture flickers then only blue and no content. No thermal faults.
• Picture is dark. No picture tube drive.
• Monitor fails in 1280 x 1024 with video controller "ARTIST XJS/T120".
• Service manual correction.
• Main board is burnt.
• Vertical fault.
• With 1280x1024 resolution menu items of a CAD program are blurred.
• Occasional general failure.
• Adjustment via software. Interface unnecessary, cable is sufficient.
• Occasionally processor indicates undefined errors.
• Adjustment via software. Interface is unnecessary, cable is sufficient. (991931011171 FIMI repair tip)
• No picture, video output stage does not function. (service info for FIMI -991931011171)
• FET Pos. no. V818 is burst.
• No picture. "H defl. failure" or "Gen. Failure" appears in the display.
• Convergence very bad in all modes.
• Spare part information (2).
• Excessive brightness. (service info for FIMI -991931011171)
• Left vertical and top horizontal menu items are blurred, if operated with CAD program 1024x768 and higher.
• Occasionally switches off when H sync >37kHz. Smell of burning or smoke, appliance operates.
• After some time set in protection mode, error high voltage.
• Transistor V815 defective. Lettering reads N414 / THD400. Resistor R922 burnt.
• Smoke from appliance.
• Resistor R910 is burnt (parallel to transformer T803, dynamic focus).
• Occasionally picture is not in focus. In DOS mode vertical lines in the left half of the picture.
• H geometry linearity is compressed on the right side.
• V-convergence statically incorrect, cannot be controlled.
• Failure of V805/V851/V853 (short circuit).
• Only black screen.
• Line drive transistor V815 (THD400) and V806 (IRF730) S/C.
• Horizontal geometry linearity is compressed on the right side.
• Scanning fault.
• Switches off after several hours. "General Error" appears in the display. Can be started again immediately.
• Dead. V806 (IRF730) and V815 (THD400) are defective.
• Failure of F601.
• No digital display. Background lighting and adjustment function ok.
• No picture. Appears after turning up G2 screen without picture content.
• Does not start. On the display the message "Missing H&V SY.D" appears.
• Totally inoperative (overscan conditions - resulting in failure of U813).
• Sporadic brightness variations.
• Picture shifted downwards. Bearing control does not function.
• Error message: Horizontal deflection failure.
• After switch-on first "PLL error", then "HV error" in display.
• Focus setting adjustment. (FIMI - 991931011171 information)
• Vertical convergence.
• Ref of transistor V806 (P8P25), R340 is defective. (Board with the 3 line output stage transistors).
• Down control and high voltage output stage (V815 and V806) fail again.
• "V-Sync out of range" then "Hi-voltage fail" error in the display. (FIMI - 991931011171 information)
• Picture is much too small.
• V convergence is out statically and cannot be adjusted.
• HI. VOL. FAILURE message on LCD.
• 'High voltage fault' appears in the display.
• Monitor does not restart after sleep mode.
• Vertical shift.
• "Mode not present" display.
• Does not start. "Missing H&V SY.D" appears on display.
• Normal picture, however when switching over to other resolutions or similar, it switches off and indicates a high voltage fault in the display.
• Ghosting on video.
• Switches off with 'high voltage fail', if the picture brightness suddenly increases greatly.
• Horizontal sync adjustment.
• Picture is very dark or poor in contrast. If the contrast is turned up fully, picture is blurred.
• Picture pumps.
• Demagnetises approx. 10 times at switch on.
• Blurry picture.
• Picture size pumps +/-2 mm. Appliance switches off occasionally. "HV-failure" appears in the display.
• Part no. info: connection rail between the front and back mains switch. (service info for FIMI -991931011171)
• No function, V806 (IRF730) and V815 (THD400) are defective.
• "High Voltage Fail" appears in the display, after various adjustments were shown.
• B+ supply voltage adjustment.
• Picture width or the entire picture pumps in all resolutions.
• Displays 'V out of range' then powers down with red LEDs flashing.
• HV error is displayed. No picture.
• Vertical convergence is incorrect.
• Error message: HV failure.
• Picture continuously gets rapidly blurred, also brightness varies somewhat. (991931011171 tip from FIMI)
• Horizontal geometry linearity is squashed on the right side.
• Picture is blurred in the corners.
• When monitor switched on, CRT is blank and LCD is OFF. (991931011171 FIMI repair tip)
• Error message: PLL error and no picture.
• Horizontal phase.
• Resistance value from the resistor parallel to coil of T803 on the appliance with deflection board and 3 power transistors.
• Error message: Horizontal out of range. (991931011171 FIMI repair tip)
• No digital display. Background illumination and adjustment function ok.
• Code number information.
• Vertical convergence is out with regard to static and cannot be adjusted.
• Degaussing starts on itself - with bad results.
• Oscillation in the picture. Video board is knock sensitive.
• Vertical height
• After switch-on display becomes lighter and lighter until desktop vanish.
• Blurred picture. Smell of burning from the line output stage.
• Occasionally dark, horizontal line in middle of picture occasionally vertical jitter. (991931011171 tip from FIMI)
• Value of R878.
• 'No V-sync' message in display.
• Monitor fails in 1280x1024 with video controller 'artist XJS/TI20'.
• Horizontal convergence.
• With a 1024x768 resolution and higher, picture becomes blurred.
• No start-up. Error message "GEN. Failure" or Horiz.-Failure".
• Displays 'V out of range' and does not start up.
• Checking ther high voltage part.
• Picture can no longer be focused.
• Vertical output stage oscillates. Black stripes on picture.
• Vertical convergence is quite wrong and cannot be adjusted.
• Horizontal stripes in picture.
• Picture is dark. No CRT drive.
• Läuft nur selten. "Brutzelgeräusch" ist zu hören. Bild zittert.
• Brightness is unstable. Picture flickers. (991931011171 FIMI repair tip)
• H/V-stage is defective. No picture.
• Goes irregularly into protection mode - High Voltage Failure.
• Shadows behind text in windows.
• Dead.
• No functions.
• No function - V805.
• Loss of data in the memory due to noise.
• Positions of transistors IRF540 and IRF9530 in the sealed high voltage box.
• No width control due to failure of 6624.
• Too little contrast.
• Picture changes brightness, not knock sensitive.
• AC/DC measurement.
• Dynamic focus is defective. Picture is blurred in the middle.
• Only runs rarely. Sizzling noise. Picture jitter.
• Error message: H-Failure.
• Failure of R804 (on the degaussing board).
• Adjustment via software. Interface unnecessary, cable is sufficient with the following configuration.
• Value of resistor (with 1 output transistor) on the main board.
• After a few seconds of self-test "General failure" is displayed.
• Error message: 'V Sync OFF' (only for a short time) then 'H DEFL. Failure'. No further function, PSU ok.
• Picture width or entire picture pumps in all resolutions.
• Flickering picture.
• No function - start voltage V17 at approx. 40V instead of approx. 15..17V.
• Specifications.
• Colour red is blinking.
• High voltage failure is displayed, No picture.
• Bad convergence.
• Display has a deflection fault.
• No function, displays -GEN.FAILURE.
• White D adjustment.