2114 / GEC [TV]

• No display. (2114 tip from GEC)
• Intermittent standby.
• Brightness varies.
• TXT picture is not centred horizontally on the CRT screen. Low TXT contrast. (2114 GEC repair tip)
• High HT. (2114 tip from GEC)
• White dots and stripes in picture centre.
• Trips.
• Whistling in standby only.
• No picture (intermittently). (2114 tip from GEC)
• Program display flashes when search key is operated. No channel can be detected.
• No switch on via RC. However can be switched over and off, everything else also functions.
• Dark horizontal bands on screen.
• PSU Whistling.
• Loss of previously stored data. Display with strange symbols. Switches to standby intermittently. Unable to select TXT.
• Sometimes comes on, trips off and goes totally dead.
• Red and green dots in picture.
• Blank raster, sound ok.
• Dead.
• Striations on left hand side.
• Squealing from PSU. Trips.
• Dead, 6.6 in display.
• No picture or intermiitent loss of picture.
• No brightness control. (2114 GEC repair tip)
• Bad patterning. Field cramp and foldover in middle of picture.
• Sometimes set does not come on when asked. No output from the power supply.
• Intermittent or poor starting.
• Poor at start up.
• Intermittently dead.
• No picture.
• No picture. Field cramp. Whining.
• Dead set, fuses not blown.
• Dead. Burning smell. (service info for GEC -2114)
• Dead set, loud whistling from the power supply. (GEC - 2114 information)
• TV channel cannot be changed when the teletext button was pressed.
• No picture, raster on the lower 2/3 of screen and no sound.
• No line drive.
• Black and white picture. Colour in TXT OK.
• Excessive HT at 172.5V.
• Dead. Whistles for 2 secs at switch on.
• No start-up. Burning smell.
• Dead. after a few minutes.
• Q801 and R816 (4R7) destroyed.
• Slow start-up.
• Dead. Chopper transformer whistles.
• No picture for first 15 - 30mins. Sound OK.
• Slow start-up. OK after a while .
• Noisy power supply.
• Vertical black line on either side of screen.
• No picture. No audio.
• Slow start-up. intermittently.
• No picture, raster only covers bottom 2/3 of screen plus whining.
• Comes on in standby and when switched on relay operates and power supply trips to zero volts.
• Patterns in picture.
• Picture takes a long time to appear.
• Auto grey scale input pulling low.
• Black lines appears on picture.
• Appliance cannot be switched to stand-by.
• Dead. Whistling. Relay chatters. (GEC - 2114 information)
• Striations and reduced width.
• No picture. Vertical collapse. intermittently.
• Bright white screen or jet black screen.
• Vertical black bars.
• Shuts down. after a few minutes.
• Line output transistor is s/c.
• Shuts down. after a while.
• 4 black bands across screen.
• Text not displayed though in TXT mode.
• Blank raster.
• Vertical black line two inches from right hand side of screen .
• No functions. Whistling.
• Tripping. Squealing noise.
• No picture. Audio OK .
• No picture or sound, high pitched whistling.
• Set jumps into and out of standby when a channel change or adjustment is being made. (service info for GEC -2114)
• Abnormal and inaccurate response to push button controls.
• Bright raster. Audio OK .
• Sticks on one channel. Appliance will not perform any other functions.
• Blank raster, sound ok.
• There was no picture or sound and the standby colons faded a few seconds after switching on.
• Width is reduced with striations on right hand side.