C1405H / GEC [TV]

• Odd characters or dots in the display window.
• Dead. Display OK.
• Left hand side of picture is dark. (service info for GEC -C1405H)
• Video is missing, blank raster.
• No red.
• Does not store memory.
• Snow in picture.
• Appliance is dead, channel display lit.
• Bright blank screen. Sound ok.
• Picture becomes half white and half black. (C1405H GEC repair tip)
• No RC function, channel change defective.
• High level of brightness which is impossible to modify by the user controls. (C1405H tip from GEC)
• Reduced height to approx 2 inches.
• High ht. F800 o/c.
• Blue picture. intermittently. Bars in picture. at top.
• Horizontal line going through centre of picture.
• Bright blank screen and flyback lines.
• Vertical roll.
• Top and bottom of field scan is increased and superimposed.
• Defective PSU.
• Set going to standby mode after running for 5 mins.
• Stuck in standby.
• Insufficient height. No vertical sync. Double line effect.
• No raster.
• Bends at top of screen on VCR PB.
• Height reduced to 2ins.
• No RC operation intermittently.
• Set tripping when switched on, odd occasion would work ok.
• Intermittently blue raster.
• No frame scan.
• Appliance is dead with number 1 and the standby LED's alight in the display. If the up or down button is pressed the number changes, but the standby LED's remains alight.
• Dead. Whines.
• Top of picture has bright thin vertical line.
• Snowy raster. No channel display or no tuning. (C1405H tips)
• No picture, no audio. Channel indicators lit.
• Reduced vertical size.
• Appliance is dead, build up of EHT then trips. Display ok.
• Goes dead after a split second.
• Intermittent frame bounce.
• Snow. No signals.
• No LEDs lit unless switched on at set switch, and mains plug inserted; then "--" is displayed and set is stuck in standby.
• No synchronisation.
• Field fault and not storing channels in memory.
• Intermittently low brightness or excessive red.
• Dead. Display shows 1.
• Tuning up and down button actuates the wrong functions.
• Appliance trips after coming on.
• Intermittent rolling.
• HT present but high.
• Blank raster, sound ok.
• Rolling and picture foldover.
• Intermittently dead.
• Dead. Channel display shows --1. (C1405H tip from GEC)
• Frame bounce or frame jumping effect.
• Line jitter.
• Stuck in standby but channel O.K
• Channel indicator only. (service info for GEC -C1405H)
• Holes and gaps in picture with blue screen.
• Intermittent standby and intermittently channel numbers change.
• Field bounce/rolling. (C1405H GEC repair tip)
• Top of picture blanks. Picture floods blue. one or both faults may depend on beam current.
• Top half of picture black.
• Intermittently thick structure of horizontal lines. I.e., one line out of every two contains no video signal info.
• Top of picture blank. Picture floods blue. one or both faults may show and both are dependent on beam current. (C1405H tips)
• Intermittently goes into standby. Incorrect operation of Ch+/Ch- buttons on TV.
• Scan is non linear. (service info for GEC -C1405H)
• Trips at switch on intermittently.
• Left hand side dark.
• Vertical instability and top part of picture cannot be seen.
• Comes on momentarily then goes dead. (C1405H tip from GEC)
• Picture size changes when varying brightness level.
• Black lines on raster and picture goes off.
• Trips.
• Bright vertical line about a third of the way across the screen on top of an otherwise perfect picture.
• HT high.
• Set going to standby mode after running for 5 minutes.
• Frame roll after set warms up. (C1405H GEC repair tip)
• Dark screen. Sound ok.
• No picture or sound, channel display "on".
• Set starts up then goes dead.
• Dead. Standby LED and channel indicators OK.
• No picture. at top. (C1405H tip from GEC)
• Dead, odd neon display lit.
• Intermittent loss of screen graphics.
• Dead. Channel display OK.
• Set is stuck in standby though it does change channels.
• The screen flashes red, green or blue when the channel is changed.
• Intermittent colour. (C1405H tip from GEC)
• Partial field collapse.
• Excessive blue in picture.
• Line and field synchronisation are missing.
• Appliance is dead but standby LED is lit.
• Inconsistant bright blue raster intermittently. (C1405H tip from GEC)
• No audio. No picture.
• Dead. Trips once at switch on.
• No colour.
• Pulses intermittently. (GEC - C1405H information)
• Low remote range.
• Blurry picture.
• No field scan. No sound, no picture.
• Comes on then trips.
• Non-linear scan. (C1405H tips)
• Picture flashes with lines on screen.
• Set comes on with standby - - signs and channel 1 but no other signs of life. (GEC - C1405H information)
• Fine bright vertical line at top of picture.
• No picture. Sound OK.
• Starts up then goes dead.
• Blank raster and video is missing.
• Switches to standby after 5 minutes; tuning up/down buttons actuate incorrect functions; does not tune; odd dots or characters in display window; no teletext operation.
• Dead. Shows "1" in display.
• Fine bright vertical lines.
• Picture appears to have holes/blank gaps and screen turns blue.
• Frame bounce or frame jumping effect.