C2093H / GEC [TV]

• Set starts up then goes dead.
• Field fault and not storing channels in memory.
• Dead, odd neon display lit.
• No picture. Sound OK. (service info for GEC -C2093H)
• Video is missing, blank raster.
• Comes on momentarily then goes dead.
• Set comes on with standby - - signs and channel 1 but no other signs of life.
• Fine bright vertical line at top of picture.
• Blurry picture.
• Frame bounce or frame jumping effect.
• No colour.
• Odd characters or dots in the display window. (C2093H tips)
• HT high.
• Defective PSU.
• Appliance is dead, channel display lit.
• Black lines on raster and picture goes off.
• Dead. Shows "1" in display.
• No picture. at top.
• Low remote range.
• Top of picture has bright thin vertical line.
• Intermittently goes into standby. Incorrect operation of Ch+/Ch- buttons on TV.
• Starts up then goes dead.
• Bends at top of screen on VCR PB.
• Intermittent standby and intermittently channel numbers change.
• No LEDs lit unless switched on at set switch, and mains plug inserted; then "--" is displayed and set is stuck in standby.
• No picture, no audio. Channel indicators lit.
• High ht. F800 o/c.
• Fine bright vertical lines.
• Holes and gaps in picture with blue screen.
• Picture size changes when varying brightness level.
• Bright blank screen. Sound ok. (C2093H tips)
• Picture becomes half white and half black.
• Frame bounce or frame jumping effect.
• Height reduced to 2ins.
• Insufficient height. No vertical sync. Double line effect.
• No frame scan.
• Horizontal line going through centre of picture.
• Dead. Display OK.
• Appliance trips after coming on. (GEC - C2093H information)
• Intermittent colour.
• Intermittent rolling. (GEC - C2093H information)
• Top of picture blanks. Picture floods blue. one or both faults may depend on beam current.
• Intermittently blue raster. (GEC - C2093H information)
• Appliance is dead with number 1 and the standby LED's alight in the display. If the up or down button is pressed the number changes, but the standby LED's remains alight.
• Blank raster, sound ok. (C2093H tips)
• Snow in picture.
• Dead. Channel display shows --1.
• Intermittent loss of screen graphics.
• Top half of picture black.
• Goes dead after a split second.
• Bright blank screen and flyback lines.
• No red.
• Intermittently low brightness or excessive red.
• No RC function, channel change defective.
• HT present but high. (service info for GEC -C2093H)
• Stuck in standby.
• Dead. Standby LED and channel indicators OK.
• Comes on then trips.
• Blank raster and video is missing.
• Switches to standby after 5 minutes; tuning up/down buttons actuate incorrect functions; does not tune; odd dots or characters in display window; no teletext operation.
• High level of brightness which is impossible to modify by the user controls.
• Dead. Channel display OK.
• Snow. No signals.
• Channel indicator only.
• Set tripping when switched on, odd occasion would work ok.
• Dark screen. Sound ok.
• Appliance is dead, build up of EHT then trips. Display ok.
• Intermittently dead.
• Dead. Whines.
• Stuck in standby but channel O.K
• Dead. Trips once at switch on.
• The screen flashes red, green or blue when the channel is changed.
• Reduced vertical size.
• Picture flashes with lines on screen.
• Trips.
• No RC operation intermittently.
• No audio. No picture.
• Vertical roll.
• Snowy raster. No channel display or no tuning.
• Inconsistant bright blue raster intermittently.
• Rolling and picture foldover.
• Appliance is dead but standby LED is lit.
• Reduced height to approx 2 inches.
• Blue picture. intermittently. Bars in picture. at top. (C2093H tips)
• Top of picture blank. Picture floods blue. one or both faults may show and both are dependent on beam current.
• Bright vertical line about a third of the way across the screen on top of an otherwise perfect picture.
• Tuning up and down button actuates the wrong functions.
• Line jitter.
• Field bounce/rolling.
• Set going to standby mode after running for 5 minutes.
• Set going to standby mode after running for 5 mins.
• Picture appears to have holes/blank gaps and screen turns blue. (C2093H tips)
• Line and field synchronisation are missing.
• Left hand side dark.
• Dead. Display shows 1.
• No raster.
• Non-linear scan.
• Partial field collapse.
• No synchronisation.
• No field scan. No sound, no picture.
• Frame roll after set warms up.
• Trips at switch on intermittently.
• Does not store memory.
• Intermittently thick structure of horizontal lines. I.e., one line out of every two contains no video signal info.
• Left hand side of picture is dark.
• Vertical instability and top part of picture cannot be seen.
• Pulses intermittently. (C2093H GEC repair tip)
• Scan is non linear.
• Top and bottom of field scan is increased and superimposed. (C2093H GEC repair tip)
• No picture or sound, channel display "on".
• Set is stuck in standby though it does change channels.
• Intermittent frame bounce.