322110 KVX2931 / HANSEATIC [TV]

• PSU IC and PSU transistor defective. (extract of circuit diagram attached) (service info for HANSEATIC -322110)
• Slow start-up. when cold. (+ extract of circuit diagram)
• OSD flickers. Intermittently buzzing sound. (part of circuit diagram displayed)
• Does not switch to standby correctly, it can be started again only by control on appliance. (picture attached)
• Picture and sound drop intermittently out. Only green programme display in picture. (+ extract of circuit diagram)
• Power supply chopper transistor 2SD1548 S/C. (+ extract of circuit diagram)
• No or intermittent start-up. Knock sensitive. (with circuit diagram extract)
• No start-up. after lightning strike. (+ extract of circuit diagram)
• Intermittent picture size. (picture attached)
• Severe hum in standby on left channel. OK in standard mode. (picture attached)
• No function with the RCU. IR receiver functions. IR data reach the microprocessor. RCU functions with another CTV. (extract of circuit diagram attached)
• Intermittently switch to PR00. (with circuit diagram extract)
• Switches to next odd number when selecting preset even number (2,4,6, etc.) (without using RC). (part of circuit diagram displayed)
• Noise in picture. at high volume.
• Occasionally varicap tuning shifts. Black picture, no sound, hum.
• Picture width twitching. Poor E/W. (picture attached)
• Picture is vertically too small and has rounded corners. (+ extract of circuit diagram)
• Switches on. Signs on the screen, green bar and sound dropout. (picture attached)
• Dark picture is lower third, upper third folded down. (part of circuit diagram displayed)
• Intermittent loss of colour or colours getting brighter and more saturated as set warms up. (picture attached)
• Faulty OSD. (with circuit diagram extract)
• Intermittently picture collapses and blanks out. (HANSEATIC - 322110 information)
• Q602 (2SD1548) blown at start up. (part of circuit diagram displayed)
• Sound goes to maximum when adjusted. (picture attached)
• No colour (after a few minutes). (+ extract of circuit diagram)
• Reduced picture size. Horizontal line. (with circuit diagram extract) (322110 tips)
• Standby LED blinks intermittently after switch on. (extract of circuit diagram attached)
• Vague horizontal bars and picture takes a long time to appear. Noise in the start up speaker. (extract of circuit diagram attached)
• No picture. No audio. after a while. (part of circuit diagram displayed)
• Dark screen. Audio OK . (part of circuit diagram displayed)
• Switches to standby. (part of circuit diagram displayed)
• No functions. Starts up, then beeps 3 times and shutsdown. (picture attached)
• Flickering colours. Knock sensitive.
• Reduced vertical and horizontal size. Low audio. (with circuit diagram extract)
• Starts up on channel 59. It is possible to set standard and channels but appliance switches back to channel 59 as soon as memory key is pressed. LEDs A and STEREO are lit.
• Starts 4 times and then turns OFF. (+ extract of circuit diagram)
• Standby LED flashes slowly. (extract of circuit diagram attached)
• Horizontally distorted picture. Rattle. (part of circuit diagram displayed)
• After start-up protective circuit switches on, after several start ups appliance functions. (part of circuit diagram displayed)
• Black screen. intermittently. (+ extract of circuit diagram)
• Picture and sound are intermittent; channel number still present. (picture attached)
• Distorted frame. (part of circuit diagram displayed)
• Picture fails. (part of circuit diagram displayed)
• Vertical collapse. (+ extract of circuit diagram)
• PSU switches 4 times, then no function.
• No RC functions or OSD. Intermittent colour, then intermittent video. (with circuit diagram extract)
• No picture (intermittently).
• No switch on from standby. The TV will not come on from standby but the standby LED is lit. 21" and 25" sets only. (+ extract of circuit diagram)
• Switches immediately to program 0 at switch on. Impossible to change. (with circuit diagram extract) (322110 tips)
• HV crackles shortly after switch on, then no function. (extract of circuit diagram attached)
• Excessive brightness with retrace lines even when brightness is on minimum. (part of circuit diagram displayed)
• Horizontal bars when switching channels. Switches off intermittently. Fault may not appear for a long time. (with circuit diagram extract)
• Dead. Standby LED lights, protective circuit starts up.
• Interference on low channels. (with circuit diagram extract)
• Warped picture after some time. (with circuit diagram extract)
• No switch on and red light on. 140V present. No input signal on line transistor base. (part of circuit diagram displayed) (HANSEATIC - 322110 information)
• Dead (intermittently). (part of circuit diagram displayed) (HANSEATIC - 322110 information)
• Starts up, red LED flashes twice then goes dead. (part of circuit diagram displayed)
• Line output stage defective. (picture attached)
• Grey screen. Retrace lines. after a few seconds. (picture attached)
• PSU fails. (part of circuit diagram displayed)
• Attempts to start up but remains unstable. Clicking noise from chopper. LED switches on at the same rythm. (322110 tips)
• Brief start up of power supply. Standby LED then flashes 4 times. (+ extract of circuit diagram)
• No audio (after a few minutes). (extract of circuit diagram attached)
• Slow start-up. (+ extract of circuit diagram)
• Switches to standby (intermittently). (picture attached)
• Power problem intermittently. At switch on the red power supply lamp may light up but the power supply may sometimes trip as in overcurrent detection. (picture attached)
• Horizontal line. (extract of circuit diagram attached)
• No functions. (part of circuit diagram displayed)
• PSU ticking. LED flashes 5 times. (part of circuit diagram displayed)
• Procedure to initialise Eprom after replacement.
• Black horizontal lines in the middle of the picture (possibly at the bottom as well). (+ extract of circuit diagram)
• Picture disappears intermittently with strong noise from FBT. Screen remains black and impossible to switch over channels. OSD remains stuck.
• Ticks 3 times, then no function. (extract of circuit diagram attached)
• Vertical line. in the centre. (picture attached)
• Q602 defective. (with circuit diagram extract)
• OSD and picture noisy. (extract of circuit diagram attached)
• Appliance blows circuit protectors PS601 and PS602.
• No channel storing. (picture attached) (322110 tips)
• Green purity smear at upper left coin and purple purity smear at upper right corner.
• Channel number flickers between two numbers. (picture attached)
• Picture size incorrect. Change in size of raster. (with circuit diagram extract) (HANSEATIC - 322110 information)
• At switch on pulsates 3 times. (+ extract of circuit diagram) (322110 tips)
• No picture. Standby LED does not light.
• Pincushion distortion. at bottom.
• Ragged verticals at bottom 2 inches. (with circuit diagram extract)
• Tripping. (+ extract of circuit diagram)
• Picture green, with green lines. (+ extract of circuit diagram)
• Pulsates 4 times, then no function.
• No colour (intermittently). (+ extract of circuit diagram)
• No picture at switch on. No OSD display. Sound present. Picture appears after 1 to 2 min. Time difference for when picture appears do not decrease significantly after switching off and on again. (part of circuit diagram displayed)
• Only channels 59 and AV present; audio is set to maximum. (picture attached)
• Horizontal lines. (picture attached)
• Appliance must be switched on for 10 minutes before picture appears. (extract of circuit diagram attached)
• Picture compressed in the centre. Black band at the bottom of the screen. (+ extract of circuit diagram) (322110 tips)
• No audio. Picture OK . (322110 tip from HANSEATIC)
• OSD flickers constantly. Intermittently goes into standby. (with circuit diagram extract)
• Intermittent HV flashover at the CRT neck.
• Picture on left side is concaved. (with circuit diagram extract)
• Attempts to start up three times, then switches to protection mode.
• OSD moves and flashes. Volume level changes spontaneously. (part of circuit diagram displayed)
• Picture is too wide, distorted, goes into safety mode if not adjusted. (part of circuit diagram displayed)
• No picture. when changing channels (intermittently). (+ extract of circuit diagram) (322110 HANSEATIC repair tip)
• Vertical foldover at top. (with circuit diagram extract)
• White horizontal lines across top of picture.
• Strong noises from demagnetizing coil after plug has been pulled out. (picture attached)
• Erratic start-up. Standby LED flashes . (+ extract of circuit diagram)
• Switch has to be pressed several times to start the appliance. Sound fault. (picture attached)
• If a program is selected,appliance switches to and fro between selected program and 00, sometimes several times per sec. Picture temporarily OK. (extract of circuit diagram attached)
• Picture has green line going down. (with circuit diagram extract)
• Drops out intermittently and switches to another channel and sound crackles. (with circuit diagram extract)
• Horizontal lines across screen. Humming. (+ extract of circuit diagram)
• Reduced vertical size. Poor vertical linearity. (with circuit diagram extract)
• No HV. (with circuit diagram extract)
• Picture foldover at the bottom of the screen. Adjustments work but fault persists, (extract of circuit diagram attached)
• No raster. Audio OK . (with circuit diagram extract)
• No RC functions. Hum in audio. (part of circuit diagram displayed)
• Squealing noise at switch on with mains switch. Appliance goes in standby. Power LED flashes. (extract of circuit diagram attached) (322110 tip from HANSEATIC)
• Cannot go to standby even after a few attempts to switch ON. (extract of circuit diagram attached)
• Dead. (part of circuit diagram displayed)
• No operation (intermittently). (part of circuit diagram displayed)
• Excessive horizontal size. E/W fault. (+ extract of circuit diagram)
• Loudspeaker crackle at switch on, no picture content.
• It may happen that during a Mono broadcasting, the stereo LED switches on. At this time, a strong audio noise may be heard.
• Tries to start up. Standby LED flashes three or four times then goes out. After insisting a few times, it eventually starts up. (part of circuit diagram displayed)
• How to adjust beat zero.
• Black screen and no sound when switching TV on in cold conditions. Standby LED lights up after a short while. TV functions OK. Loud "plof" noise in loudspeakers. (with circuit diagram extract)
• 12V missing on IC608. (part of circuit diagram displayed)
• No driver transistor Q805 command. (picture attached)
• Picture height too low and rolled-up from the top.
• Switches to protection mode. after start-up. (HANSEATIC - 322110 information)
• OSD bounces intermittently from left to right. If it bounces too intense, brief loud sound interference appears and program switches over or switch on problems occur. (extract of circuit diagram attached)
• Flickering picture. (picture attached)
• No RC functions. (with circuit diagram extract)
• Error codes. (picture attached)
• No picture or sound after a while. OSD shows video output. (extract of circuit diagram attached)
• Switches to video input if a VCR is connected via scart and VCR is switched to standby. (+ extract of circuit diagram)
• A space between the tube and the cabinet may be visible. (322110 tips)
• No picture, no RC reception, LED flashes a few secs.
• Poor vertical linearity (stretched at the top, collapsed at the bottom). (picture attached)
• Stuck in standby. Comes on when powered ON/OFF a few times but with no picture for approx. one min; followed with flyback lines as set warms up. (picture attached)
• CATV interference. (+ extract of circuit diagram)
• No switch on from standby. Power supply shuts down. (part of circuit diagram displayed)
• Vertical deflection fails or only vertical lines are visible. (with circuit diagram extract)
• Stations drift off tune or search does not stop. (extract of circuit diagram attached)
• Q602 (2SD1548) blows at start up and fuse blows. (part of circuit diagram displayed)
• No degaussing.
• OSG jitters, audio crackles and loss of colour. (322110 HANSEATIC repair tip)
• Crackling noise. Flash-over at switch on.
• Black screen. Audio OK . (+ extract of circuit diagram)
• Pulsating picture.
• Flyback lines. at top. (with circuit diagram extract) (322110 tip from HANSEATIC)
• Frizzy picture width which is not constant. (extract of circuit diagram attached)
• Horizontal white line. (with circuit diagram extract)
• Picture only appears approx 2 mins after switch on. Audio OK. (+ extract of circuit diagram)
• Picture is poor with flyback lines and pulsing brightness. (part of circuit diagram displayed)
• Strong colours. (picture attached)
• No start-up. (extract of circuit diagram attached)
• Switches automatically to another channel after approx. 5 min. Preferentially to channel-S2 (112.25 MHz). Intermittently tuner switches to another frequency also. (+ extract of circuit diagram)
• No vertical synchronisation on bright picture content via scart.
• Power supply hiccups. (part of circuit diagram displayed)
• No picture. No audio. intermittently. OSD OK .
• Picture runs through. (with circuit diagram extract)
• Program display appears suddenly. Then RC doesn't function any more. (+ extract of circuit diagram)
• Hum at switch on. Purity spots.
• No start-up. when cold. LED blinks . (picture attached)
• Picture is red. If colour contrast is reduced, picture is black-white.
• Tuner IF fails. Picture is red then black. (extract of circuit diagram attached)
• No synchronisation. (+ extract of circuit diagram)
• Occasionally appliance cannot be switched on from the mains switch. (+ extract of circuit diagram)
• Picture appears slowly. (+ extract of circuit diagram)
• B1 board change.
• Picture and sound is intermittent or negative picture.
• No reception (intermittently). (extract of circuit diagram attached)
• Purity errors and E/W distortion.
• Lines in picture. (picture attached)
• Cramped at centre, stretched at top and fold over at bottom. (extract of circuit diagram attached)
• No picture. Audio OK . (+ extract of circuit diagram)
• After a while skips to another program station at random. (+ extract of circuit diagram)
• Poor picture. Flyback lines. (+ extract of circuit diagram)
• Intermittent colour (after warm-up).
• No picture. Text has one colour missing. (+ extract of circuit diagram)
• Vertical foldover at bottom. Reduced vertical size. (extract of circuit diagram attached)
• Hiccups 4 times and then fails (in cold condition). (+ extract of circuit diagram)
• Shaking picture. Tearing picture. Distorted picture. (with circuit diagram extract)
• Vertical amplitude too low . Bad vertical linearity. Dark picture at bottom. (extract of circuit diagram attached)
• Pincushion distortion. (part of circuit diagram displayed)
• Intermittently top of screen rolls, loses colour, picture pulses or twitches.
• Channel memory loss at switch off. No volume control. Remains on original adjustment. Program OK. Channel tuning OK. (with circuit diagram extract) (service info for HANSEATIC -322110)
• Pulsates 4 times on start up from mains and then switches off. No standby display. (picture attached)
• Chopper transistor S/C. (extract of circuit diagram attached)
• Switches off by itself. at start-up.
• Doesn't start up with mains switch when cold. Standby LED flashes 4 times. (with circuit diagram extract)
• No tuning.
• Vertical output stage bcomes defective after few weeks. (with circuit diagram extract)
• 137V voltage collapses at switch on. (with circuit diagram extract) (322110 tips)
• +B voltage can not be adjusted. (with circuit diagram extract) (322110 HANSEATIC repair tip)
• Picture is too wide and fails when warm. (extract of circuit diagram attached)
• Flickering picture. No picture. intermittently. (extract of circuit diagram attached)
• Volume uncontrollable. (part of circuit diagram displayed) (322110 tip from HANSEATIC)
• Purple stain on top right-hand side corner. (322110 HANSEATIC repair tip)
• Low audio (on the right). (part of circuit diagram displayed)
• Pincushion distortion. on sides. Excessive horizontal size. (+ extract of circuit diagram)
• Channels drift and go back to 00. (extract of circuit diagram attached)
• Jumps from program site 2 to 00, jumps to and fro, then stays on program 00. (picture attached)
• OSD channel insertion remains permanently in the picture. Can be switched off with the RC. (extract of circuit diagram attached)
• Screen remains black or picture is poor.
• Diminishing power supply. (extract of circuit diagram attached)
• Blank raster. (with circuit diagram extract)
• Retrace lines. after warm-up. (part of circuit diagram displayed)
• No picture. Sound only via AV. Brightness, colour, control OK. (+ extract of circuit diagram)
• Picture and sound disappear intermittently. On-screen display is disturbed. (picture attached) (322110 tips)
• FET chopper transistor BUZ91A fails. (with circuit diagram extract)
• Green picture. Black screen. intermittently. Audio and OSD OK .
• Low contrast comes up after while. Flyback lines. (part of circuit diagram displayed)
• Picture disappears after short operation. OSD oscillates. (extract of circuit diagram attached)
• No raster. (picture attached)
• Poor picture with red line.
• Picture collapses. Sound is cracking. LEDs light up and go out. OSD flickers. (extract of circuit diagram attached)
• Black and white picture with strobe effect. (extract of circuit diagram attached)
• No start-up. when cold. (extract of circuit diagram attached) (service info for HANSEATIC -322110)
• OK at switch on, then after few secs, sound becomes loud, picture flickers, field cramping, picture loss then reappears expanding away with loss of field scanning, then goes dead. (with circuit diagram extract)
• Width is reduced and verticals bent. (+ extract of circuit diagram)
• Switching transistor and mains fuse fail repeatedly. (+ extract of circuit diagram) (322110 HANSEATIC repair tip)
• Fine stripes in upper quarter of picture. (part of circuit diagram displayed)
• Intermittently microprocessor locks up with parental lock displayed. No signals. (part of circuit diagram displayed)
• Power supply voltage is too high. Cannot be adjusted with pot. (picture attached)
• Tuner adjustment is off tune. Fine tuning does not store information.
• Volume varies. (+ extract of circuit diagram)
• Sporadic interference from loudspeaker.
• Starts up 4 times, then no function. (extract of circuit diagram attached)
• Slight top foldover plus 6 faint flyback lines (2 red, 2 green, 2 blue). (extract of circuit diagram attached)
• No TXT. (extract of circuit diagram attached)
• Only a green streak in the middle of screen. OSD appears on this streak. (322110 HANSEATIC repair tip)
• Dead. No standby. Switches 3x quietly. (extract of circuit diagram attached)
• Blurry picture. (+ extract of circuit diagram)
• Retrace lines. (+ extract of circuit diagram)
• Teletext ok. Otherwise only a dark picture with digit OSD without sound. (picture attached)
• PSU transistor and fuse 4A are destroyed after 1-3 mins. (+ extract of circuit diagram)
• Poor linearity. at top. (picture attached)
• Flashing horizontal black lines. Occasionally appliance may function OK. (part of circuit diagram displayed)
• No OSD. No reception. Black screen. Standby LED flickers every 20 seconds. (extract of circuit diagram attached)
• White horizontal lines in picture. Broad lines when cold. Thin lines when warm, or no lines. (+ extract of circuit diagram)
• No start-up from standby. (picture attached)
• Intermittent symptoms - picture rolls, goes black and white with pulsing, or line twitching occurs at the top of the picture.
• Dark picture with red stripes. Picture is OK after approx 5 mins, but red is missing.
• HT too high at 175V. (with circuit diagram extract)
• TXT doesn't function. Greenish background.
• Insufficient height and cramping at centre of screen. (picture attached) (322110 tips)
• OSG sways from side to side. (extract of circuit diagram attached)
• Cramping at bottom of screen, width reduction and loss of audio. (picture attached)
• Picture flickers and breaks down (wobbles).
• After working ok for a while, interference on picture and sound. Channel display always shows "00". (with circuit diagram extract)
• Bright bar at top of screen. (+ extract of circuit diagram)
• No start-up. intermittently. (+ extract of circuit diagram)
• Cycles on/off. (picture attached)
• Deflection fault, distortion and picture oscillation at bottom of screen. (picture attached) (HANSEATIC - 322110 information)
• Vertical lines are ragged. (with circuit diagram extract)
• Occasionally picture and sound disappear (go out of tune), mainly a short time after switch on, if appliance is cold.
• Channel OSG sway intermittently from side to side then set powers down. (picture attached)
• The screen is black or very dark. (+ extract of circuit diagram) (322110 tips)
• Horizontal lines from top to bottom on screen. (picture attached)
• Picture too big. Switches off by itself. (+ extract of circuit diagram)
• No vertical deflection. (with circuit diagram extract)
• Picture distorted and reduced. Picture becomes longer when hot. (with circuit diagram extract)
• Yellow, approx 5mm vertical line through the picture. (picture attached) (322110 tip from HANSEATIC)
• No audio. OK via SCART . No picture.
• Switches to program site 00 after operating for a while.
• Vertical line. (+ extract of circuit diagram)
• No audio. (picture attached)
• Resembles incorrect tuning, or the appliance goes to mute. (picture attached)
• OSD flickers. Speakers whistle. (part of circuit diagram displayed)
• Rustle of EHT at switch on then powers down with LED flashing four times. (with circuit diagram extract)
• Picture appears and disappears with horizontal sync tearing. (part of circuit diagram displayed)
• Crackling audio. when cold. Knock sensitive. (part of circuit diagram displayed)
• Frame output chip blown repeatedly. (+ extract of circuit diagram)
• It is constantly on program site 2. Analog values can be adjusted but bounce back immediately to the initial value (with circuit diagram extract) (322110 tip from HANSEATIC)
• Starts up three times then switches off. (with circuit diagram extract)
• Vertical streaks. at top. (picture attached)
• Degaussing does not work on the sides of the picture.
• Power supply goes on and switches then on and off rhythmically. Several white streaks on screen for a short while. (+ extract of circuit diagram)
• Starts up at switch on, red LED flickers then appliance goes dead. (picture attached)
• Red flyback lines. (part of circuit diagram displayed)
• Vertical lines are bent inwards in the corners of the picture. (picture attached)
• PSU transistor fails again after approx 3 mins. (+ extract of circuit diagram)
• Distorted picture and vertical sync when switching on
• Poor colour. One colour missing. Low brightness. (picture attached)
• Wrong colours which are displaced half inch to the right. (+ extract of circuit diagram)
• Sound only briefly present, then only mute.
• No start-up from standby with RC.
• Contrast too low in certain mode. A dark picture is displayed in the rgb mode. (part of circuit diagram displayed)
• No picture. (with circuit diagram extract)
• Switches after switch on immediately to channel site 33. If set is switched on with button 1 on RC, it switches to channel 33.
• OSD fades away. (picture attached)
• Channel drift.
• Distorted audio. The speaker cabinet vibrates.
• Pulsates four times at switch on and then switches to standby.
• Program number OSD is permanently displayed. (extract of circuit diagram attached)
• Pale or distorted picture or black and white picture. (with circuit diagram extract)
• Pulsates four times then switches off.
• When connecting TV in cold conditions, picture flickers. Knock sensitive fault. (extract of circuit diagram attached)
• Pulsating picture. Distorted picture.
• Screen doesn't light up. HF noise from loudspeakers. (extract of circuit diagram attached)
• Switches to standby (after start-up). (with circuit diagram extract)
• Varicap voltage drift.
• Black hum bar type effect for first few secs after channel change. (+ extract of circuit diagram)
• Programm jumps from 2 to 32 or from 4 to 36 or from 6 to 38 after some time.
• Starts up with a plopping noise from loudspeakers. Bright horizontal stripes in tuner picture in the first minutes of operation. Intermittently picture and sound OK after half an hour. (extract of circuit diagram attached) (322110 tip from HANSEATIC)
• Only starts up after several attempts or PSU switches off again.
• Lines approx 5cm at the top. (part of circuit diagram displayed)
• Stuck in standby. (+ extract of circuit diagram)
• Text picture geometry distorted.
• Picture rolls/goes B/W or line twitching at top of screen.
• Loss of picture. Picture shows flashes.
• Attempts to start up once, gives three pulses and then goes into safety mode.
• Black screen. No RC functions. (+ extract of circuit diagram)
• Black screen. No display. (extract of circuit diagram attached)
• No RC functions. intermittently.
• No colour. via SCART. (part of circuit diagram displayed)
• At switch on picture takes longer than usual to appear (tube unblocking). (picture attached) (322110 tips)
• Flyback lines. Dark picture. after a while. (with circuit diagram extract)
• Signal loss on all channels with red or blue characters. Bright points on screen as if aerial disconnected. Picture is OK sometimes but with no colour.
• Distorted picture. Interference in picture. (extract of circuit diagram attached)
• Varicap adjustment (tuning) shifts intermittently.
• Poor linearity or geometry. Frame linearity fault. Usually only occurs in sets which are more than two years old. (with circuit diagram extract)
• Dim picture. Excessive brightness. (with circuit diagram extract)
• Rhythmical ticking after start-up. (with circuit diagram extract)
• Loud noise intermittently and no picture after start-up. Error appears rarely. (extract of circuit diagram attached)
• No start-up. LED blinks . (picture attached)
• Pumps, starts after several attempts. Picture and sound OK.
• Intermittently PSU does not start up. (with circuit diagram extract)
• No subtitles with the "Subtitles for the hard of hearing" decoder. (+ extract of circuit diagram)
• OSG are black and should be green.
• No or intermittent start-up. (part of circuit diagram displayed)
• Switches to protection mode. (with circuit diagram extract)
• No power up. Standby LED flashing with 12 secs intervals. (part of circuit diagram displayed)
• The white balance varies when changing the colour intensity. (part of circuit diagram displayed)
• Horizontal, black lines in picture depending on for how long the appliance is ON. Usually after a while RC will also no longer function. Sometimes the opposite effect, RC does not work then after a period of time black lines appear. (extract of circuit diagram attached)
• Dynamic convergence is out of adjustment.
• +B too low, can only be adjusted from 90V to 120V (extract of circuit diagram attached)
• When increasing volume of appliance via RC, sound becomes lower by itself after finishing the adjustment, also when lowering volume appliance becomes louder or lower ie. sound varies. (extract of circuit diagram attached)
• Switches on twice for a short time switches off.
• Sound level decreases. OSD shows decrease.
• Power supply starts up and goes then to PROTECT mode. Standby light on. (part of circuit diagram displayed)
• Service information. Original tuner (SUF944PLL) is replaced by tuner U944C. Only for UK models. (picture attached)
• PSU pumps three times at switch on. Standby LED switches off.
• Mechanical screeching, whistling, chirping from HV unit. (part of circuit diagram displayed)
• No picture after 5 mins. It bounces twice, then screen becomes dark. Program display is 00. If program is selected again, picture reappears. (part of circuit diagram displayed)
• Flashing picture. Applicable to sets which have a new B1 board without a screening can. See also bulletin TV00692. (part of circuit diagram displayed)
• OSD flickers, picture disappears after a while. (part of circuit diagram displayed)
• No picture. No OSD. (with circuit diagram extract) (322110 tip from HANSEATIC)
• Veil and picture oscillation. (picture attached)
• Vertical jitter. LED blinks . Trips. (with circuit diagram extract)
• Spot on right of picture. (322110 HANSEATIC repair tip)
• Poor colour reproduction. Brightness adjustment doesn't function. (with circuit diagram extract)
• Dark picture with on-screen display, no sound. Videotext is OK. (picture attached) (322110 tip from HANSEATIC)
• Shuts down (intermittently). (+ extract of circuit diagram)
• Shuts down. (part of circuit diagram displayed)
• Picture sometimes becomes slanted with underlining. (with circuit diagram extract)
• No power supply. Rattle for a few seconds. (with circuit diagram extract)
• Flashing picture intermittently. May also have colour dropout. See also bulletin TV00593.
• IC8170 blows at switch on. (+ extract of circuit diagram) (322110 tip from HANSEATIC)
• Intermittent colour and picture flashing.
• After a flash goes back to channel 0. OSD displays VIDEO 00. (+ extract of circuit diagram)
• After a while starts switching between the channel where it was at that moment and channel 00. After restart remains on channel 00. (part of circuit diagram displayed)
• White or RGB stripes on the upper part of picture. (part of circuit diagram displayed)
• Red picture. Flyback lines. Trips.
• Colour disappears after switching to a different channel. (with circuit diagram extract)
• Service information. Mcb connecting leads. (picture attached)
• Channels change at random.
• Blocked on one programme place and when switching it always goes back. (+ extract of circuit diagram)
• No start-up. after warm-up.
• Intermittently stops. (picture attached)
• Sound crackles with OSD flashing. (picture attached)
• Trips 3 times then enters safety mode. (with circuit diagram extract)
• OSD shifts after approx 10 mins then no picture and no sound. (+ extract of circuit diagram)
• Bright screen and retrace lines about 2 inches from top. (+ extract of circuit diagram)
• PSU pulsates. (part of circuit diagram displayed)
• Stuck in Canal Plus. (picture attached)
• Picture appears slowly. when cold. No audio. intermittently. (with circuit diagram extract)
• On screen display is constantly mixed up. Flickering picture and plopping sounds. (picture attached) (service info for HANSEATIC -322110)