NEVADAII / KITON [TV]

• Stretched picture. (picture attached)
• PSU pulsates. Switches to standby. after a while.
• Switches off from standby, LED is briefly green, then goes back to red.
• Dark picture. OSD OK . (service info for KITON -NEVADAII)
• PSU pulsates. in standby.
• Appliance fails and can only be started after a long time.
• Reduced vertical and horizontal size. (with circuit diagram extract)
• Picture shifted vertically. at bottom.
• Blank raster.
• Shuts down. after a few seconds. HV OK. .
• R717 (2K2) burnt repeatedly.
• Chirping. at start-up. Trips. (with circuit diagram extract)
• No adjustments are possible.
• Blue picture, no drive. Sound OK.
• Reduced horizontal deflection.
• R914 is defective. (with circuit diagram extract)
• Intermittently Q605 blown. (with circuit diagram extract)
• Intermittent picture and audio or does not find channels.
• Faulty OSD. (with circuit diagram extract) (KITON - NEVADAII information)
• At power up green LED is on for 2 secs, then flickers, set goes to standby. (with circuit diagram extract)
• Flyback lines. (with circuit diagram extract) (service info for KITON -NEVADAII)
• Dark picture. Colour varies. Colour flickers.
• Ticking noise. No start-up. (part of circuit diagram displayed)
• PSU ticks in standby and hisses in full load mode.
• Dark picture. Raster OK .
• Colour varies. Flickering picture. (picture attached) (KITON - NEVADAII information)
• Tripping. (+ extract of circuit diagram) (NEVADAII tip from KITON)
• Dead. Standby LED flashes . (part of circuit diagram displayed)
• Programs are not stored after switch off.
• Excessive horizontal size. (+ extract of circuit diagram)
• Line output stage (BU2508D) fails. R629 (2R7) burnt.
• Flickering picture. Bent verticals. (with circuit diagram extract)
• Picture appears for several secs, then becomes dark and switches to protection. Sound OK.
• Excessive brightness. Flyback lines. (picture attached) (service info for KITON -NEVADAII)
• After start-up front LED is red, becomes green shortly and then red again. Dummy load lamp lights up shortly and then goes out.
• LED flickers. Light rhythmical noise, otherwise no function.
• Vertical collapse. (extract of circuit diagram attached)
• Bent verticals.
• No functions. (picture attached)
• Reduced horizontal size. Audio OK .
• Distorted sound. Volume cannot be adjusted.
• Slightly cramped blank raster with flyback lines. In centre of raster there are coloured lines, slight E/W bow. (picture attached)
• Dark picture. (+ extract of circuit diagram)
• No start-up from standby. LED flickers .
• Line BU508A fails again immediately.
• Black screen.
• Does not always switch on. Pumps after switch on. (NEVADAII KITON repair tip)
• Does not accept SCART input. (picture attached)
• Low HT. (extract of circuit diagram attached)
• Q802 is S/C. (+ extract of circuit diagram)
• Poor East/West correction. (picture attached)
• Snowy raster. Reduced width. No tuning. Unable to access SERVICE mode. Locks up if picture menu entered.
• BU2508AF fails intermittently. (extract of circuit diagram attached)
• PSU pulsates. (with circuit diagram extract)
• Switches to protection mode (after a while).
• No start-up from standby. LED is red .
• Clicking noise. after start-up. (extract of circuit diagram attached)
• Over/under scan.
• Vertical fault.
• Switches to standby at switch on, LED turns green for a sec.
• Excessive horizontal size. Pincushion distortion. on sides. (with circuit diagram extract)
• Picture and sound interference.
• No start-up. LED is red . Clicking noise. (+ extract of circuit diagram)
• White retrace lines on screen. (with circuit diagram extract)
• Horizontal lines.
• No picture. Raster appears at start-up.
• Audio output chip IC100 fails repeatedly.
• Standby LED flashing green. (with circuit diagram extract)
• Black screen. Audio and OSD OK .
• Defective Q605 (BU508AF) line output transistor. (part of circuit diagram displayed) (NEVADAII KITON repair tip)
• Low brightness.
• Takes long time to appear. Comes up quicker if first anode control adjusted. (+ extract of circuit diagram) (NEVADAII KITON repair tip)
• Moire on band 1.
• Tripping. at start-up.
• To avoid anode voltage peaks. (part of circuit diagram displayed)
• Picture quivers depending on brightness.
• Negative picture. (+ extract of circuit diagram)
• No contrast. at start-up. (NEVADAII tip from KITON)
• Picture too large. E/W defective.
• Clicking noise. (with circuit diagram extract)
• Picture shifted to the right. No colour. (picture attached)
• Picture too small. Distorted picture. (picture attached)
• Locking codes misfunctioning.
• No horizontal deflection. (picture attached)
• Vertical collapse (intermittently).
• Goes to standby, when pressing Volume, Mute or Menu buttons.
• Picture collapses intermittently with E/W fault. White line in the middle. Sound crackles.
• Shuts down (intermittently).
• Comes on in standby, then if power button pressed blinks pale green.
• Horizontal line.
• Operates in short bursts.
• No startup. LED lights up at switch-on.
• No luminance. (part of circuit diagram displayed)
• Red standby light changes to green then switches back to red.
• LED blinks green.
• Mains transistor fails immediately again. Netztransistor stirbt sofort wieder
• Distorted picture (N/S), like in 16:9 format. Bars on top and at the bottom.
• No OSD. (with circuit diagram extract)
• Standby is red and becomes green for 2 secs after switch on.
• Reduced horizontal size. Standby LED flashes .
• White, bright screen with flyback lines.
• Switches to standby. after a few seconds. (part of circuit diagram displayed)
• Horizontal line. in the centre. (picture attached)
• Chopper transformer fails.
• Vertical lines. (with circuit diagram extract)
• Line transistor blown shortly after switch on. (picture attached)
• No E/W correction.
• No TXT just number 100 in the left corner.
• Power supply blown. (part of circuit diagram displayed) (NEVADAII tip from KITON)
• Picture lost, then screen is black and RGB test lines moving in top half of screen.
• No TXT (intermittently). (with circuit diagram extract) (NEVADAII tip from KITON)
• Relay trips. (extract of circuit diagram attached)
• Goes off with a bang and bright light from the inside.
• No picture (intermittently).
• Slight flicker after five mins, worsens as time goes on. Colour flickers ON/OFF. (picture attached)
• HV sparkling. (with circuit diagram extract)
• E/W fault. Screeching noise. Line output transistor fails repeatedly.
• No TXT. (extract of circuit diagram attached)
• No tuning. (part of circuit diagram displayed)
• Adjustments in service menu.
• E/W fault. intermittently.
• No start-up from standby. Green led flashes twice then switches to red.
• No front panel function. RC OK.
• Vertical collapse. after a few minutes. Flyback lines. on upper half screen. (picture attached) (NEVADAII tip from KITON)
• White vertical stripes at upper picture edge. Picture becomes blank after a while.
• No audio. in NICAM .
• S/C in mains transformer. (part of circuit diagram displayed)
• Severe picture bowing after a minute or so.
• Snow in picture. (extract of circuit diagram attached)
• No picture (dark with barely visible spots). (picture attached)
• Vertical foldover at top and bottom. (with circuit diagram extract)
• No picture in PIP mode. (with circuit diagram extract)
• Only one primary colour with flyback lines.
• Burst electrolytic capacitor C829 (47uF/160V).
• Switching transistor in primary PSU is S/C.
• IC802 (MC44604P) fails repeatedly.
• Standby OK, green LED flashes twice briefly after start up attempt and goes to standby.
• Blurry picture. (+ extract of circuit diagram)
• Insufficient height, about 3" down at top.
• No deflection. Switches on with RC, display changes to green. Standby display available.
• Dark picture with three coloured lines in upper third. Sound OK. (with circuit diagram extract)
• Black edges on top and at the bottom. Picture is available though all adjustments are set to minimum. Cannot be adjusted and no storage.
• Noise from PSU. Strong hiccup. (extract of circuit diagram attached)
• Leaking in HT transformer.
• Moire or line in picture with some band 1 stations (eg. channel 4) on certain aerial equipment.
• Reduced E/W on all widescreen scan formats. (with circuit diagram extract)
• Dead. Standby LED does not light. (+ extract of circuit diagram)
• White screen. Retrace lines. (picture attached)
• E/W fault (after a while).
• No picture. intermittently (after a while). Faulty TXT.
• Picture is OK, but it is necessary to readjust G2 at each start-up, otherwise screen becomes black.
• Picture foldover. Switches to standby.
• Picture twitches. Horizontal cogging.
• PSU blown.
• Picture flickers with 3 coloured lines in upper side of picture.
• No picture, no sound. Standby diode flashes briefly green at switch on.
• Line BU transistor becomes hot.
• PSU pulsates. LED blinks . (+ extract of circuit diagram) (service info for KITON -NEVADAII)
• No horizontal drive at pin 40 of deflection processor. (+ extract of circuit diagram)
• Disable hotel mode.
• No HV. (+ extract of circuit diagram)
• Compressed picture at the top.
• Switches to standby. after a few seconds. LED is green.
• Excessive height. Foldover at top. Lines missing at top of picture. Different coloured vertical stripes across picture. (+ extract of circuit diagram) (NEVADAII tip from KITON)
• Does not switch to standby.
• Weak contrast. (+ extract of circuit diagram)
• E/W fault. (with circuit diagram extract)
• Wavy picture. on sides.
• PSU transistor fails at start-up. (+ extract of circuit diagram)
• Bright picture. (picture attached)
• Stuck in standby. Squealing from PSU.
• Bright green raster with flyback lines. (with circuit diagram extract)
• Clicking noise. in standby. (with circuit diagram extract)
• Low audio. (part of circuit diagram displayed)
• No start-up. LED is red after operating mains switch. If switched on (via program key on user control or RC) LED lights green and then goes off.
• Narrow, bowed picture. E-W faulty.
• Transformer failure.
• Voltage Usys is only 35V.
• Reduced horizontal deflection. Reduced vertical deflection. Vertical foldover. at top and bottom. (NEVADAII tip from KITON)
• No tuning. Poor synchronisation. Shifted phase.
• Stuck in standby. (with circuit diagram extract)
• No function. PSU is dead.
• Line output transistor fails repeatedly.
• Flyback lines. at top. (extract of circuit diagram attached)
• Black screen with three colour lines. Sometimes half a picture appears.
• No functions. Standby LED flashes .
• Grey screen. Audio OK .
• IC (TDA6108JF) fails after 12 hours operation.
• Shuts down (after a few seconds).
• Slow start-up. (extract of circuit diagram attached)
• Reduced vertical size.
• Dead. LED is green.
• Power supply problems. (NEVADAII tip from KITON)
• Blue screen.
• No picture. Bright raster (after a few minutes). (part of circuit diagram displayed)
• No picture. Audio OK . (extract of circuit diagram attached)
• Dead. LED blinks .
• D611 fails. Q605 becomes hot.
• No front panel function.
• No picture. No OSD. Audio OK . (with circuit diagram extract)
• Piecrusting in picture. (KITON - NEVADAII information)
• Switches to standby intermittently. Comes on with RC but switches off after a while.
• No video signal on screen, picture dark, OSD display OK. (NEVADAII tips)
• Ripple on verticals.
• Dead. (extract of circuit diagram attached)
• Black stripes in white picture areas.
• No signal (intermittently).
• Tripping. LED blinks .
• Shuts down. intermittently. Burning smell.
• Stuck in standby. Green LED flashes . (NEVADAII KITON repair tip)
• No PIP. (picture attached)
• No audio in SECAM L mode.
• Reduced horizontal size. Pincushion distortion. on sides. (with circuit diagram extract)
• Vertical end stage line. (NEVADAII tip from KITON)
• No colour. (part of circuit diagram displayed)
• Bright horizontal stripes.
• Hum bar. No RC functions. (extract of circuit diagram attached)
• Shuts down after start up. Led blinks red/green a few seconds.
• No functions. when cold.
• Shuts down. after start-up.
• Blank screen with 3 coloured (R G B) lines across screen.
• Excessive HV. (+ extract of circuit diagram)
• Picture appears briefly but resorts to four horizontal lines. Sound OK. (extract of circuit diagram attached)
• No horizontal or vertical deflection (intermittently).
• BU2508 fails.
• Whistling.
• Low contrast.
• PSU pulsates quickly, audible via speaker. (part of circuit diagram displayed)
• Picture collapses. Shock sensitive.
• No picture. after warm-up. Audio OK .
• PSU destroyed.
• Line output transistor and TDA4605 is also defective.
• Picture in only one colour with flyback lines.
• R809 blown. (+ extract of circuit diagram)
• No line drive. (+ extract of circuit diagram)
• Washed out picture. (picture attached)
• Tripping sound from power supply. (with circuit diagram extract) (NEVADAII tips)
• No start-up. Standby LED tries to go green then goes back to red.
• Blank raster with 2 red, green and blue horizontal lines, approx one third down screen. (extract of circuit diagram attached)
• Tuning drifts. (picture attached)
• Power supply fails. Loud noise in the chopper.
• Excessive blue. (extract of circuit diagram attached)
• Slow start-up. No start-up. intermittently.
• LED lights briefly green after switch on. PSU starts up but appliance goes back to standby.
• White screen. (part of circuit diagram displayed)
• Appliance goes to standby if switched on with RC. Standby LED flashes green.
• Picture size varies with picture content.
• Channel shifts after station is changed. After retuning, everything is OK.
• BU2508AF is S/C. (extract of circuit diagram attached)
• E/W fault. Switches to protection mode. (NEVADAII tip from KITON)
• Enter service mode.
• No start-up. Standby LED lit .
• Pincushion distortion. (picture attached) (NEVADAII tips)
• No functions. LED is green.
• Ticking noise from speaker in standby (Burst mode). (picture attached) (NEVADAII KITON repair tip)
• LED blinks, then switches to standby.
• Pulsating picture. Shuts down. (extract of circuit diagram attached)
• Grey picture with flyback lines.
• Poor picture. (with circuit diagram extract)
• Switches to standby when picture appears or picture pulsates slowly via AV or at low brightness.
• Picture too small.
• No or poor synchronisation. (with circuit diagram extract)
• Occasionally slight flashover in the picture.
• No vertical deflection. (with circuit diagram extract)
• Picture reduced horizontally in 16/9 and 4/3 mode.
• Sizzling at start-up. (service info for KITON -NEVADAII)
• Picture width is too low and perhaps smoke develops. (with circuit diagram extract)
• Green picture. Flyback lines.
• BU2508D fails immediately at switch on.
• Dead. Power LED lit . (picture attached)
• Excessive horizontal size. intermittently. E/W fault. (extract of circuit diagram attached)
• Spots in picture. in the centre. (+ extract of circuit diagram)