TLG1007 / NIKKAI [TV 36/37 (34-36) cm picture]

• Intermittent frame bounce.
• Insufficient height or the height varies.
• LEDs not lit or only partially lit.
• Appliance trips when warm.
• Frame collapse or intermittent frame collapse.
• Dead.
• Excessive brightness. Flyback lines.
• Stops tripping if C811 PSU is disconnected.
• Horizontal centre adjustment.
• Poor picture quality, smearing, milkiness, glistening on peak whites or insufficient brightness. (service info for NIKKAI -TLG1007)
• Outside of picture is wavy (depending on beam current).
• Intermttently powers down.
• Striations and flyback lines.
• Intermittent manual channel change.
• Snowy picture and field roll.
• Red, blue or green luminance signal is missing.
• Frame collapse with no sound.
• Tuning drifts (intermittently).
• Intermittently dead.
• Horizontal oscillation alignment.
• Various symptoms:- no tuning, no sound, full sound, dead set etc.
• Blanking problems.
• Raster is blank with flyback lines.
• Sound and vision (drop out, signal missing).
• Poor line sync and intermittent colour.
• Dead. PSU pulses. (service info for NIKKAI -TLG1007)
• Displayed channel no. does not match the channel.
• Protection circuit trips too early.
• Channel display number does not correspond to channel. (TLG1007 tip from NIKKAI)
• No colour.
• Picture has moved to one side.
• Reduced horizontal size.
• Reduced vertical size.
• Line oscillator does not function.
• No raster. Sound OK.
• Blank raster.
• Channel changes at random. (service info for NIKKAI -TLG1007)
• Tripping (intermittently).
• No contrast.
• Field roll with a snowy picture.
• Height is reduced and picture foldover.
• The appliance is dead (tripping).
• Reduced field scan with foldover.
• Field blanked from 1 to 3 inches at top of screen.
• Only snow, no display.
• Focus problems.
• No vertical deflection.
• "O" symbols with tails fill screen on TXT; bar for analogue settings flash.
• Trips.
• EHT brushes or arcs.
• Inadequate colour identification.
• PAL matrix phase adjustment.
• No audio. No picture.
• Focus adjustment.
• Intermittently RCU does not function.
• Vertical circuit adjustment.
• VIF alignment.
• Field bounce or jittering. (service info for NIKKAI -TLG1007)
• Reference oscillator adjustment.
• Infra-red receiver does not function.
• White balance adjustment.
• Occasionally appliance switches off.
• When volume increased row of dots indicate volume still at minimum.
• Stuck in standby. (NIKKAI - TLG1007 information)
• Chopper transistor TR13 S/C.
• Picture snowy looks like a tuner fault.
• Intermittent loss of signals and randomly unhappy about channel three selection.
• Field collapse, no sound.
• TXT lines.
• Field sync is missing.
• Frame oscillator does not function.
• Synchronisation is missing or intermittently missing.
• Reverting to channel 1.
• Vertical jitter.
• Signal is intermittent. (NIKKAI - TLG1007 information)
• No picture.
• Ballooning effect.
• Raster is green with flyback lines.
• Picture is grainy and sound noisy.
• The appliance has a dark picture.
• Blank raster. Audio OK .
• Tuner only memorises stations with even numbers.
• Vertical size adjustment.
• PAL matrix amplitude adjustment.
• Incorrect line speed.
• Appliance trips when changing channel.
• There was a snowy raster but no sound or channel indicator illumination.
• RF AGC adjustment.
• Low width and a dim picture, improving slowly over about an hour. (service info for NIKKAI -TLG1007)
• Switched mode power supply trips when warm.
• Horizontal shift fault.
• Brightness fault.
• Picture tube is not lit.
• Incorrect frame linearity.
• Convergence adjustment.
• Unstable picture, line hold control has no effect.
• Video processor oscillation frequency adjustment.
• Vertical collapse.
• Intermittently changes channel by itself. Volume varies and goes to standby.
• EHT missing, line timebase ok.
• Goes back to channel 1.
• Vertical foldover at top and bottom.
• Field sync fault.
• Raster is blank only flyback lines present.
• Stripes over the picture.
• Dead or intermittently dead.
• Dark picture.
• Ghosting effect.
• Blank raster but sound and on screen display ok.
• Frame synchronisation poor.
• Stuck on channel 1. No signal intermittently.
• The output of the power supply falls slowly until the point where the field cramp becomes apparent.
• Width is reduced and picture is faint.
• Set does not start up.
• Channels cannot be tuned in or stored.