VN7200 / NIKON [Camcorder - 8mm]

• Pixel repair for LANCLink Interface.
• Wavy representation of vertical lines.
• Servicing the CF33 flexible board.
• Transport noise in FF, REW and PB.
• Closes and starts to load, then jams.
• Broken focus ring, zoom OK.
• Door will not close.
• No eject. Other functions OK .
• Service information. Psion based EVR software is available.
• Cassette compartment will not release.
• Service information. Wiping cloth for video heads and drum.
• Loud head drum motor noise may be recorded through the microphone.
• Focus stuck. (VN7200 tips)
• Service information. The mecha chassis block is now available.
• No PB or REW.
• Mechanical noise in REW, PB and REC.
• Irregular loading. The cass tape may stick to the drum resulting in the tape being ejected. (last emergency - drum pg error).
• 28MHz origin adjustment.
• ATF servo fails during PB.
• Ejection of cassettes is defective, blocked mechanically.
• TG1 arm falls out.
• Does not load tape. No eject. Fault occurs intermittently. .
• Service information. When servicing the camera the flange back may be shifted when pushing around the zoom reset sensor.
• Automatic focus and zoom fail intermittently.
• Intermittent transport.
• When in REW, drum reverses. When loading the drum slows down, then the tape is unloaded.
• Unit will not close door. When applying power, mechanism ejects OK, but will not set back to load/unload state.
• No mechanical operation. The bulletin illustrates a procedure to be followed to determine if the T reel and S reel need replacement.
• Ticking noise from mechanism in all modes.
• Mechanical noise.
• Eject inop ( TG-1 lever comes off it's guide ) (NIKON - VN7200 information)
• No eject intermittently. Capstan motor possibly doesn't rotate. Intermittently ejects. Capstan motor not rotating.
• Jig information. Ez clip jig helps repair, adjustment and maintenance of models equipped with the ez connector.
• No picture. in camera mode.
• Drum runs at high speed when power is applied.
• Loads tape then ejects immediately.
• No Eject. Caution LED flashing. E-E OK.
• Does not load tape.
• Loud zoom noise can be heard when recording.
• Does not load tape. intermittently.
• Mechanism loads halfway without cassette, rewinds a few seconds and stops.
• Does not accept tape.
• Date and time memory is occasionally lost.
• Unit loads half way. Drum fails to change direction, then unit unloads.
• Does not accept tape. Closes OK without one.
• Will not load tapes (intermittently no rewind). Mechanism only half loads then slowly attempts to finish.
• Switches off after a short time. Take-up reel jolts.
• Modification/circuit change. Iris replacement.
• Intermittently does not accept tape. (VN7200 tips)
• No tape loading, loads ok without a tape. No drum rotation.
• Speed problem. T guide arm and rail base guide replacement procedure.
• Tape spills out when REW is selected.
• Tape jams.
• Parts of picture shift horizontally. Looks like drop out. No visible drop outs in FM signal.
• New publication.
• No eject.
• Cassette stuck in appliance and "caution" warning is displayed. (service info for NIKON -VN7200)
• Switches continuously from SP to LP.
• Does not REC Hi-8.
• Part no. info: Crank lever.
• Incomplete battery charge. When charging an NP-500 in the camera, the battery may not be charged to 80%, or the charging LED may not be lit up.
• Destroys under side of tape.
• Mechanism jammed. intermittently.
• Tape stuck in mechanism, no functions. Loads OK.
• Does not accept cassette. Mechanical crunching noise.
• Reduced horizontal size. in viewfinder.
• Camera switches off again immediately since the supply table is not driven.
• RK gear goes under supply reel in REW and breaks.
• No unloading or ejecting of tape.. Although the unloading operation during eject is normal the cassette compartment does not rise.
• Mechanical noise. Mechanical noise during rew, or noise captured during REC.
• No eject. Powers down with caution indicator blinking.
• Picture in viewfinder is darker on the left with vertical lines.
• Does not load tape. No drum/head rotation.
• Bright points in pixel. 1-CCD defective pixel repair.
• Microcomputer versions and evr data settings.
• Mechanical noise. Mechanical noise during rew, or noise captured during REC.
• Doesn't load cassette. Creaking noise from the mechanism.
• Does not switch to standby. Power problem.
• Part number information. Ccd imagers without any defective pixels are now available for this camcorder.
• Low audio level. PB sound level is too low, a kind of echo can be heard; muffled sound.
• Too low volume on recordings with a built in microphone.
• Eats tape.
• No Zoom function.
• Cassette ejects but new cassette cannot be inserted.
• Failure of flexible membrane may result in various faults.
• Unstable picture. Oil on the tape or on the tape path may cause picture distortion, head clogging, tape eject or no drum rotation.
• Blocks intermittently during tape unloading.
• Part number information. Cable kit.
• The take up reel table does not rotate with an inserted cassette.
• Cassette compartment won't rise
• Caution light on when loading.