6205IMC 989532 / NORDMENDE [TV]

• Adjusting the SECAM (4.25MHz) colour carrier trap: Chassis.
• Horizontal vawes in lower image half.
• Secondary protective switch TV01 and TV02 intermittently tripping. (with circuit diagram extract)
• Two hours after line transformer was replaced, appliance switches off, as soon as high voltage has built up. (6205IMC NORDMENDE repair tip)
• Dark picture. (with circuit diagram extract)
• Excessive brightness. (with circuit diagram extract)
• The stand by led flashes up at second intervals. The appliance only functions at a reduced mains voltage.
• E/W fault.
• Setting the audio trap.
• Vertical wave lines, especially in lower image half. (6205IMC tips)
• Crack in sound. (NORDMENDE - 6205IMC information)
• Adjusting the NTSC(3.58MHz) colour carrier trap: Chassis.
• At switch on high voltage builds up. Occasionally flashovers in the picture tube or on the base. Occasionally S2000 fails. Drive and PSU are ok.
• Adjustment of screen grid voltage: chassis.
• Only noise on screen, screen menü cannot be superimposed. Does not react to RC or control panel commands. (service info for NORDMENDE -6205IMC)
• TL19 in line end stage defective. (+ extract of circuit diagram)
• No start-up. Standby LED lit .
• Grey adjustment: CRT board.
• Appliance pumps continuously. (with circuit diagram extract)
• Crackling at switch off.
• Black horizontal bars in picture. TXT picture is only partially visible.
• Adjusting the PAL amplitude: chassis.
• Occasionally does not start up from standby.
• Adjusting the deflection- and geometry values.
• No direct time OSD possible. (NORDMENDE - 6205IMC information)
• Adjusting the peak white: chassis.
• No start-up from standby. intermittently.
• Slow start-up.
• Does not come on from standby, red standby light comes on. (extract of circuit diagram attached)
• Vertical deflection error. Horizontal stripes in picture. Noise.
• Dark picture. OSD OK .
• Dark screen. (6205IMC tip from NORDMENDE)
• Dead. (part of circuit diagram displayed)
• Pulsates. Buzzing sound. (6205IMC tip from NORDMENDE)
• No function, high voltage builds up for a short time then switches off.
• After a few minutes screen becomes very bright and flyback lines become visible, then everything comes back to normal. Symptom keeps recurring.
• Adjusting the R-Y demodulator: chassis.
• No functions. Standby LED does not light.
• No raster. Screen lights up.
• Instructions how to go into the SERVICE mode.
• No start-up from standby with RC.
• PSU fails after switch on.
• Starts briefly, then it switches off again. PSU pulsates.
• Always pulsating. (with circuit diagram extract)
• No picture after 30 mins.
• Transistors in the PSU and horizontal part fail simultaneously after 90 mins. (NORDMENDE - 6205IMC information)
• Line transistor fails immediately after switch on. (6205IMC tip from NORDMENDE)
• At switch on HT builds up but then BU fails.
• Vertical line. (picture attached)
• No TXT. (part of circuit diagram displayed) (NORDMENDE - 6205IMC information)
• Vertical lines are distorted horizontally.E/W equalisation can not be adjusted correctly.
• Fails after approx. 5 mins.
• Dead, standby point cannot be seen, no secondary standby voltage, no 8V voltage at collector of TP16 (BC368). (part of circuit diagram displayed)
• Setting the bell filter: chassis. (service info for NORDMENDE -6205IMC)
• No start-up. intermittently.
• No image content. Image dark. (+ extract of circuit diagram)
• PSU does not always start after switch on via front control or RC. (6205IMC tip from NORDMENDE)
• Coloured tinge in picture.
• No audio.
• Reduced vertical size. (6205IMC NORDMENDE repair tip)
• Line stage does not start up.
• Vertically non-linear image. Noise coming from vertical deflection board.
• Switches off after approx 3 secs from start-up.
• Setting the SECAM identification: chassis. (6205IMC tip from NORDMENDE)
• White alignment: picture tube board.
• After turning on vertical image is intermittently shifted up by approx. 2 cm; after approx. 10 minutes it returns to normal position. (extract of circuit diagram attached)
• Distorted image. Strong streaking effect. (part of circuit diagram displayed) (6205IMC NORDMENDE repair tip)
• Dead. Standby LED does not light.
• Intermittently picture shifts with approx 2 cm on top at start-up. OK after 10 mins.
• Picture is OK but picture width changes at brightness change. If picture width is decreased flickering in picture.
• Sound flutters or is distorted.
• Adjusting the main voltage (Usyst. 143V): Chassis.
• TP29 fails after switch on.
• After completing chassis with the TXT decoder VT294 there is a bright spot approx 5cm high in the lower quarter of the screen. Remainder of the screen is dark.
• Picture flickers with coloured OSD (eg from a VCR). (+ extract of circuit diagram)
• No start-up.
• Contrast average value is too high. (picture attached) (6205IMC tips)
• Too low vertical amplitude; cannot be adjusted with VA control to nominal value. (part of circuit diagram displayed)
• No audio. No picture. Squealing from PSU. (+ extract of circuit diagram)