6205IMCNIC 0989532G58 / NORDMENDE [TV]

• Siren noise in the speaker.
• When switching off the appliance in standby and with the mains switch there is a loud crackling in the speaker. (extract of circuit diagram attached)
• Blackish bar after whites.
• Red raster. Horizontal lines.
• Blows intermittently and switches on again. (extract of circuit diagram attached)
• At start up there is a power supply fault. TP29 must be replaced. After this the picture lacks vertical and horizontal amplitude. Reduced picture which has shifted to the bottom of the screen. (part of circuit diagram displayed)
• Works for 10 secs then goes into standby. TV ok after switching off then on again.
• Line in centre of picture.
• No signal.
• HV starts up for 3-5 secs then shuts down. (extract of circuit diagram attached)
• 3cm white line at top of picture. No sound and no video, not even in scart. Green LED on.
• Coloured tinge in picture.
• U/Syst voltage is 106V. (with circuit diagram extract)
• Picture is somewhat noisy.
• Does not switch to standby.
• S2000AF blows each time appliance is plugged in. (picture attached) (6205IMCNIC NORDMENDE repair tip)
• The channel nos run through, no sound or picture but it works in video.
• Standby LED flickers and PSU does not start up correctly.
• Shuts down.
• Switches off by itself. intermittently. Standby LED lit .
• Picture is displaced from frame towards top part of screen (approx 4cm).
• Grey scale incorrect. Yellow-green picture. High voltage on the blue cathode (170V). Voltage on the red cathode, as well as on the green, is normal (135V).
• HT whistles for a short time. Standby LED remains lit. Raster is defective. (picture attached)
• Occasional memory fault when appliance is stopped by the general switch. When switched on again, appliance is deprogrammed. (extract of circuit diagram attached)
• PSU pulsates. Standby LED flashes . (picture attached)
• Faint picture because CRT was defective.
• Distorted picture. No adjustment possible . (6205IMCNIC tip from NORDMENDE)
• No stations found in search. Seems to have poor power supply filtering.
• The picture blows.
• No volume control via RC.
• No 15V.
• At start up snowy screen with no reception. When pressing the programme keys the numbers run through continuously. No sound.
• White screen. Audio OK .
• No start-up from standby. (picture attached)
• Power supply goes to standby and standby light is lit up.
• Picture has increased at the top and reduced at the bottom of screen.
• No picture on upper half of the screen. Small part of picture in lower half of the screen. Just a small stripe in lower screen. Appliance switches to protection mode.
• No reception. (picture attached)
• Power supply fault. Remains in standby. (+ extract of circuit diagram)
• No colour, only on French channel "La 3".
• When warm picture foldover towards the bottom and horizontal flyback lines. Noise from the line transformer. (picture attached) (NORDMENDE - 6205IMCNIC information)
• Picture width and height twitches intermittently, thereby noise or chirping can be heard in SM transformer.
• No start-up from standby. after warm-up. (+ extract of circuit diagram) (6205IMCNIC tips)
• Crackling noise from power supply then dead.
• Cuts out intermittently. Light becoming white before turning red. No start up with RC. (extract of circuit diagram attached)
• TV does not start up. TV01 not in safety mode.
• Occasionally there is no light at all.
• Switches off after approx 3 secs. PSU switches on with brief chirping noise and then switches off.
• Tripping. Standby LED flashes .
• Power supply pulsates after a frame fault.
• Horizontal collapse. (picture attached)
• No start-up. intermittently. PSU pulsates.
• BU transistor TP29 blows again.
• Picture is narrower. When making adjustments, the picture is wavy at the sides.
• No start up. No standby. (extract of circuit diagram attached)
• After an extended operating time TP01 (BUT12A) fails. (+ extract of circuit diagram)
• Switches on, line transformer comes on then goes into standby immediately.
• Reduced vertical size. (with circuit diagram extract)
• Bottom of raster is missing. Deflection incomplete.
• PSU does not always start up (start up difficulties). (extract of circuit diagram attached)
• S2000AF in power supply is defective. Functions OK for a week, then S2000AF and primary fuse defective. (+ extract of circuit diagram)
• Starts up three times then goes into safety mode. (part of circuit diagram displayed)
• Varying light intensity of standby LED. No start up but intermittent low hum.
• Short line pulses on the line output collector and then dead. (picture attached)
• Crackling effect on video and echo.
• No functions. (part of circuit diagram displayed)
• Line output S2000 fails after a while.
• When switched on, the standby light lights up but the power supply is tripping. (+ extract of circuit diagram)
• Trips. (+ extract of circuit diagram)
• The lamp is weak.
• Set is dead but not tripping.
• Intermittent goes into standby when changing channel, also sound goes up and down intermittently. (picture attached)
• Black, horizontal lines in picture. (extract of circuit diagram attached)
• Picture instability depending on sound.
• No colour (when switching).
• Switches off immediately if vertical plug is pulled out. (part of circuit diagram displayed)
• Picture with predominant yellow/green.
• Vertical line. in the centre.
• Trips. after a few minutes.
• Blows intermittently.
• No vertical deflection. (picture attached)
• No start up of line transformer and LED pulsates slightly.
• No start-up (intermittently). (picture attached)
• White screen in scart and no sound. Picture ok via tuner. Displays programmes and sound level etc.
• E/W correction can only be poorly adjusted. (+ extract of circuit diagram)
• Stuck in standby. LED lit. .
• Slow start-up.
• At switch on starts up with severe noise in loudspeaker then stops and remains in standby.
• US (110V 90º - 143V 110º) goes high after a few mins and TV trips.
• Lines appear at top of screen or interference then goes into safety mode. At present it goes into safety mode each time after 2-3 secs. (+ extract of circuit diagram)
• Bright picture. Flyback lines.
• Dark picture. Can only be slightly adjusted.
• Dead. No voltage on the secondary. 300V on collector TP29. All the transistors and diodes are ok. Even no standby light. (service info for NORDMENDE -6205IMCNIC)
• Unstable frame linearity.
• White line. at bottom.
• Tripping. Power LED lit . (+ extract of circuit diagram)
• Switchover to another program site is not carried out.
• Picture breaks up and crackles on sound.
• The tinge varies.
• Stuck in standby. Hum in audio. (picture attached)
• Switches on but no user controls from front control panel nor from RC. Does not even switch to FF.
• Functions for 5 mins then all the channel numbers begin to run through constantly while each time the picture comes up again and RCU does not function.
• Noise bar. after a few minutes.
• No start-up (when cold). (with circuit diagram extract)
• One start-up attempt with HV,then switches to standby.
• Over-accentuated fizzling sounds. (NORDMENDE - 6205IMCNIC information)
• Regular ondulations on the vertical lines of a test picture. (part of circuit diagram displayed)
• The appliance goes to secondary safety mode. (picture attached)
• Does not start from Standby or switches off.
• No line output funtion. OK at switch on.
• Picture is at the lower picture edge and in time becomes a line. (with circuit diagram extract)
• White screen with flyback line or no brightness.
• No picture, only snow. in PIP.
• Picture shifted vertically.
• Screen is dark. Slight noise from the line output transformer. (service info for NORDMENDE -6205IMCNIC)
• Low contrast.
• Line at the bottom of the screen then goes into standby.
• Appliance works only in Burst mode. Red LED flashes.
• No picture scanning.
• Shuts down after 10 mins. Power LED remains lit. (+ extract of circuit diagram)
• No start up. No U1 47V, U2 5V voltages.
• Attempts to start, then suddenly stops.
• Burst of EHT. (with circuit diagram extract)
• Can not be switched on from standby via RC.
• Standby light lights up for 2 seconds then goes off. Appliance does not start up.
• Instructions for repairing the PSU. (with circuit diagram extract)
• Goes into SAFETY mode and very slight hum in LF.
• TV01 and TV02 are in safety mode.
• White screen. Flyback lines.
• TV starts up for a few secs with a jerky noise then stops and continues like this.
• E/W correction cannot be changed. (6205IMCNIC tips)
• Colour saturation.
• Switches to standby (after a while). (with circuit diagram extract)
• Channel memory loss approx every fortnight.
• The PSU runs continuously.
• Occasionally after switch on vertical centering is shifted up approx 2cm. Goes into normal position after approx 10 mins. (extract of circuit diagram attached)
• Vertical line wavering at left hand side. (extract of circuit diagram attached) (NORDMENDE - 6205IMCNIC information)
• No E/W correction. when cold.
• When the focus pot is varied the brightness varies after a few minutes, the picture turns dark.
• Functions very well via the scart socket. No UHF VHF reception. Display on the screen is correct, white screen. (extract of circuit diagram attached)
• TV does not start up or stops.
• Black screen. via RF output. OK via SCART .
• No picture. No sound. Switches off after 3 secs, remains in standby and has an afterglow fleck. (extract of circuit diagram attached)
• Vertical collapse. (with circuit diagram extract)
• No start-up. LED blinks .
• No reception. in UHF. (service info for NORDMENDE -6205IMCNIC)
• Reduced horizontal size.
• Control board CDI 2000.
• Vertical compression and very dark picture, more on the right than on the left.
• PSU pulsates. (+ extract of circuit diagram)
• Remains in standby or goes to standby intermittently.
• Goes into safety mode for no apparent reason, after operating for 30 mins. Starts up again from the switch.
• Line BU blows at once. (extract of circuit diagram attached)
• Switches to standby. after a few seconds. (extract of circuit diagram attached)
• TDA8178 heats up too much and blows.
• No audio. via tuner. No picture. via tuner. OK via SCART .
• No picture at switch on. Picture appears when changing channel.
• No start up of PSU. Low ticking. (extract of circuit diagram attached)
• No start up. PSU does not oscillate. (6205IMCNIC tip from NORDMENDE)
• No sound or picture. Standby light switches on and goes off in a regular rhythm. (extract of circuit diagram attached) (service info for NORDMENDE -6205IMCNIC)
• Switches to standby (after a few seconds). (with circuit diagram extract)
• At switch on colour is delayed.
• No start-up. LED is red .
• No horizontal deflection. Protective circuit trips. Standby light flashes. (part of circuit diagram displayed)
• Primary power supply fails under load.
• Pumps.
• No colour during Canal Plus.
• Erratic start-up. No or intermittent start-up. (picture attached)
• The picture is smaller and at the bottom of the screen.
• Power supply pumps. Standby LED flashes.
• Small screen, only inner side lights up.
• Tuning drifts after 20 mins.
• Starts up at switch on with the red light lit. Impossible to go into standby via the control panel or RC. (+ extract of circuit diagram)
• PSU function description.
• Intermittently PSU doesn't start up via RC and mains.
• No functions. Standby LED lit .
• PSU fails immediately after start-up.
• 4cm vertical scanning for a few secs.
• No picture, no sound, standby display dot and horizontal bars over the screen light up in display. Can only be switched on with RC.
• Black screen, alarm noise and orange LED.
• FP01 blows at switch on.
• No EHT. Black screen.
• With S2000 when warm, PSU cuts out, starts again, cuts out etc. (picture attached)
• Power supply S2000 blows approx every 10 hours.
• Power supply pulsates every single second. Standby LED flashes.
• Intermittently black band in the middle of the screen then increases in size to fill the whole of the screen. (picture attached)
• No memory during programming.
• TP29 is destroyed after 30 minutes.
• Dead (intermittently).
• Ignition on the EHT (flame). (with circuit diagram extract)
• After 5 mins a noise like rapid crackling occurs at the scanning level. Noise disappears if picture is misframed upwards. (extract of circuit diagram attached) (6205IMCNIC tips)
• Sound but no picture. White screen with flyback line. (6205IMCNIC NORDMENDE repair tip)
• Picture with flyback line on one colour.
• Switches off by itself. after a few minutes. (6205IMCNIC tips)
• Switches to protection mode. at start-up.
• No line drive.
• Switches to protection mode. (with circuit diagram extract)
• RL27 burnt.
• No channels.
• Only a horizontal line at bottom of picture.
• TP29 blows occasionally at start up or after operating for some time.
• Line transformer starts up then stops.
• 1 flyback transformer pulse then standby. If the picture appears, one time out of five there is crackling in the transformer then standby. (6205IMCNIC tips)
• Secondary protective circuit TV01 and TV02 disconnects intermittently.
• No start up of line transformer.
• Replacing the TL19.
• No scanning. (service info for NORDMENDE -6205IMCNIC)
• Weak colour.
• Normal sound, white screen, no picture, flyback lines. Impossible to reduce the brightness. (NORDMENDE - 6205IMCNIC information)
• Us is too high at 121Vpp instead of 52Vpp.
• Very white lines at the top of the screen.
• No functions. after warm-up.
• Switches to standby. in PB.
• Switches to standby (intermittently). (extract of circuit diagram attached)
• No channel reception after changing tuner and IF.
• Poor E/W correction. Adjustment of the amplitude is ok. (+ extract of circuit diagram)
• Green picture. No contrast. (part of circuit diagram displayed)
• Random loss of station memory when CTV starts up.
• To improve IF response.
• No manual or RCU command. Blocked on one channel, OSD apparent, sound present. (picture attached)
• Dark picture. (+ extract of circuit diagram)
• Pulsates if TV is started up after being put into standby.
• PSU does not strat.
• TP29 and TL19 fail after operating for 1 hr. (with circuit diagram extract)
• No reception. EHT flashovers. (6205IMCNIC NORDMENDE repair tip)
• FBT is s/c twice a year. On collector TL19. 1200V instead of 1000V. CL21, CL22, CL24, CL23 replaced but fault persists. US adjusted to 143V. FBT 470034-81 CTV TA6326.
• Power supply crackles once then dead. (service info for NORDMENDE -6205IMCNIC)
• EHT arcing noise.
• Picture with red as the predominant colour and flyback line apparent on the screen.
• Stuck in PAL.
• At switch on, standby light flashes once and cuts out.
• Thermal R349 O/C every 3 or 4 months. (with circuit diagram extract)
• Blue fails - occasionally blue flyback lines visible.
• Coil LG08 (situated in the corner near the EHT) burns. (picture attached)
• Dark stripes in picture by bright picture content. Volume display jumps. Beam spot at switch off.
• White stripe at the top of the screen. It is 1cm high and not as wide as the screen. No picture. (6205IMCNIC NORDMENDE repair tip)
• No picture (intermittently). AV OK .
• Sound and picture cut out for a second then return to normal. (picture attached)
• Picture position shifts vertically by approx 2cm towards the top of the screen intermittently. Position returns to normal after approx 10 mins.
• Switches to protection mode. after a few seconds.
• Oblique lines towards the top of the screen and there may be a demagnetization fault and the demagnetization coil is ok. The PTC has already been changed.
• TL19 in line output stage is defective.
• Intermittently blows chopper transistor.
• Under certain conditions (static discharge etc.) may revert to factory set up mode. (6205IMCNIC NORDMENDE repair tip)
• Appliance in burst mode. No standby light.
• Fuse FP2 (630mA) blows.
• In VHF range (channel 5-12) white flecks and grey haze in the picture.
• No audio. No picture. Squealing from PSU. (with circuit diagram extract)
• Intermittently switches off. Tapping effects.
• With high contrast PSU trips then starts again. Occurs randomly. (extract of circuit diagram attached)
• When switched on, line transformer attempts to start up then goes to standby. (with circuit diagram extract)
• No picture. Excessive brightness. Retrace lines.
• Does not find channels or finds one channel tuned incorrectly.
• No brightness and incorrect OSD. OSD background is bright red. (+ extract of circuit diagram) (6205IMCNIC NORDMENDE repair tip)
• Cuts out and then starts up from time to time after working for several hours.
• One colour missing.
• To improve alignment.
• Blows fuses.
• Grey adjustment: picture tube board.
• No red (intermittently).
• Wavy picture.
• Starts up in standby. Standby display ok.
• Dark screen with short bright flashes.
• Power supply chopper blows.
• No colour (via SCART).
• Mini raster scanning.
• In stand-by the light does not light up and the TV does not come on again.
• No bottom of raster. Incomplete deflection.
• Distorted audio. Distorted picture. (6205IMCNIC tip from NORDMENDE)
• Occasionally sound and video drift on channel 64. Operation is good on the other channels.
• Sound has increased to maximum, after a moment, neither RC nor manual commands work.
• Unstable picture.
• White setting: picture tube board.
• Black stripes on upper and lower picture edge.
• Impossible to go into standby via the front panel or the RC. Starts up at switch on with the red light lit. (extract of circuit diagram attached)
• White screen. Sparks between pins 6/7.
• Only a horizontal line at top of picture. (picture attached)
• White stripe on the left side of screen.
• Mono sound is OK. Stereo sound scratches .
• Fault at top of picture about 4cm after 30 mins.
• No function either from control panel nor RC. No OSD.
• The power supply blows. (6205IMCNIC tip from NORDMENDE)
• Vertical foldover at bottom.
• There is little light.
• Picture vibrates in the rythme of sound.
• Standby LED flashes bright and dark.
• Chopper goes short circuit; after replacement appliance functions correctly for approx 1 minute.
• Power supply pulsates intermittently when cold or warm.
• White picture and flyback line. New FBT. S2055AF replaced by S2000AF which heats up and blows after a min.
• Vertical lines run over the top part of the screen.
• Picture at the bottom. No contrast.
• Blank raster.
• No startup. Alarm noise from loudspeakers.
• After clicking and tripping a few times, power supply remains blocked in standby at switch on.
• Shuts down. at start-up.
• Vertical lines are jagged.
• Signals reduced to quarter of their size and are distorted on TL19 after 3 secs from start-up. TL19 burns if left under load. (picture attached)
• After appliance has been moved, strange colours. Red has become blue and screen is affected by a mauve halo. (6205IMCNIC tip from NORDMENDE)
• FBT is started up by a signal but appliance does not start. In standby mode.
• Occasionally static discharge. (service info for NORDMENDE -6205IMCNIC)
• The grey scale is incorrect. (6205IMCNIC tips)
• Switches to protection mode. intermittently.
• Compressed vertical. Extremely dark picture, more on the right than on the left.
• TV01 blows after operating for 30 mins.
• Pale grey screen with fine horizontal line and hum at start up of the line transformer. (extract of circuit diagram attached)
• TV switches off when changing channel and with great variations in the beam current.
• Low contrast on TXT and OSGs.
• Black lines on the picture. Poor sync.
• Shuts down. intermittently. (picture attached)
• No functions. IR01 does not accept reset.
• Small flyback line at top of screen on left side.
• Noise bar. at bottom.
• Line scan transistor is in S/C. (service info for NORDMENDE -6205IMCNIC)
• Distorted picture.
• No switch on at start up. Standby light is off. At stop light comes on weakly then goes off.
• Switches off when switching channels. Only switches on again after RC switches to standby. Occasionally functions OK all evening but sometimes switches off when channel is initially changed. (extract of circuit diagram attached)
• Shuts down (intermittently).
• Picture bright, dark or faint with flyback lines. (6205IMCNIC tips)
• Reduced horizontal deflection.
• Poor start up of PSU. Occasionally starts up but sometimes does not, especially when warming up. (extract of circuit diagram attached)
• Impossible to change standard, remains in SECAM. Picture inverted in PAL.
• Switching off fault of the spot.
• The appliance fails, no picture, no sound, base raster or horizontal lines.
• Goes into protective switching. (picture attached)
• Little or no light. (6205IMCNIC tip from NORDMENDE)
• Picture has vertically shifted with approx. 2cm towards top after start-up. Picture ok after approx. 10 mins.
• Intermittently increases and decreases in size both width and height. (service info for NORDMENDE -6205IMCNIC)
• No picture. Audio OK . (6205IMCNIC tips)
• Repeated failure of HOT.
• Tuning drifts.
• Excessive vertical size.
• No HF reception. Snow on picture.
• Trapezoid picture.
• Fuse fails. (6205IMCNIC NORDMENDE repair tip)
• Does not come on from standby, red standby light comes on. TV01 and TV02 in the protective circuit respond.
• Defective picture, poor colour and white dot at switch off.
• Picture is green, red and blue with flyback lines.
• Starts nomally but if appliance stops after heating up for some time, TV flashes and may take a long time to start up again. (part of circuit diagram displayed)
• Picture pulling on bright scenes.
• PSU starts for a few secs then collapses while pumping on the standby point.
• Colour fault.
• No start up except at a certain temperature. Standby ok. (+ extract of circuit diagram)
• Picture is displaced slightly towards top of screen.
• Power supply starts up 3 times at switch on then switches off. No picture or sound. Red LED is lit.
• TL19 becomes hot and fails after approx 15 secs.
• No light. Poor picture. Occasional horizontal tearing. If G2 is pushed in as far as it will go picture is better. Varies from 100 to 950V, 90 degree model, 114V on DP50.
• No TV picture and humming from loud-speaker.
• Vertical lines are distorted horizontally. E/W equalizer can not be adjusted correctly.
• Weak contrast.
• Vertical foldover.
• When set to standard adjustments the contrast value is too high.
• Blue tint in picture intermittently.
• Occasionally horizontal tearing and horizontal stripes. Same faults via aerial and in scart.
• Two black bars in TXT. (6205IMCNIC tip from NORDMENDE)
• At switch-on, vertical centering of picture offset by 2 cm towards the top of screen.
• TV starts up for a few secs and leaves a motor noise in the speaker. By disconnecting DL13, the appliance starts up again.
• After a few minutes the screen goes black and motor boating occurs.
• White band on top of screen. Only a buzzing noise coming from loudspeaker.
• No audio (via SCART).
• No raster deflection. No picture, only vague light in background. Looks like coloured spot at bottom of picture.
• The appliance has a dark picture. (service info for NORDMENDE -6205IMCNIC)
• Occasionally no scanning is possible.
• Low brightness.
• Arcing with sparks and cracking sounds. (6205IMCNIC tips)
• Starts up then goes into protection mode. Standby light on. Sound OK but no picture. Bluish screen with shadows.
• When cold picture is very white with flyback lines and hum in sound.
• Contrast average value is too high. (picture attached)
• Occasionally wide interference lines (similar to a defective HF-cable) appear on the screen. Picture is ok via Scart.
• Standby LED lights up and TV switches on, then 2 or 3 lines across screen and appliance switches to standby.
• Occasionally small horizontal black line at the top of the screen and line transformer whistles slightly.
• Line output stage immediately defective after switch on. (with circuit diagram extract)
• Volume of basic adjustment is too loud.
• TV stops and starts up again immediately. Standby light is on.
• Goes into safety mode when first switch on.
• Occasionally the TV pulsates at start up.
• No start-up (after warm-up).
• Distorted picture. Lines in picture.
• No line oscillation. (part of circuit diagram displayed)
• Menu display is in a wrong language.
• No picture or OSD information. RC and front panel do not function.
• At switch on the light comes on. CTV starts up then cuts out,no light, crackling noise at the level of the power supply transformer. (picture attached)
• Vertical picture position shifts intermittently upwards approx 2 cm after switch on. It is OK after approx 10 mins.
• No frame sync in PB of recent rented cassettes.
• Fails. (+ extract of circuit diagram)
• No sound with a Nintendo game. Game functions on another TV. (+ extract of circuit diagram)
• After changing FBT which sparks, the very high tension is ok. No light on the screen even when forcing G2 44469905.
• By pressing the buttons PROG + and - on the front panel the channel nos run through continuously. When disconnecting the control panel, difficulties in programming a channel. (part of circuit diagram displayed)
• At switch on PSU goes defective.
• Safety mode comes into play.
• Switches off intermittently (often at programme switch).
• Blue flash in Secam.
• Does not pick up in UHF or in VHF.
• No colour (after a while).
• No colour from aerial or scart. IC TA8559CN has been replaced. Wave peaks at MP output are correct.
• No reception. OK via SCART .
• Picture runs through, impossible to stabilise.
• No start-up. Red LED blinks. (part of circuit diagram displayed)
• B/W picture in PAL. (NORDMENDE - 6205IMCNIC information)
• No videotext mode.
• No raster signal on pin 31 of IV01.
• Poor scan.
• Field centering off-set by 2cm toward top of screen when first switched on. (with circuit diagram extract)
• Memory loss or random deprogramming of uP.
• Poor start up performance of the power supply.
• Scanning at bottom of screen.
• No start up of PSU, sometimes intermittently.
• No synchronisation. (with circuit diagram extract)
• When 120V at variac, UL1 reaches 280V.
• No start up of power supply. No standby light. No noise.
• Incorrect oscillations on line BU (S2055).
• Only noise on screen, screen menu cannot be superimposed. Appliance does not react to the RCU or to control panel commands.
• Picture jitters. in TXT. (picture attached)
• Poor framing.
• Switches on but switches off after a few mins. Intermittently switches off immediately. (service info for NORDMENDE -6205IMCNIC)
• Adjusting the R-Y demodulator: chassis.
• PSU fails immediately after switch on.
• All the secondary voltages are low.
• Grey picture with 6 flyback lines without picture content.
• At start up functions normally for 20 to 50 secs then goes into standby prematurely. (with circuit diagram extract)
• No picture. at bottom.
• Starts up then switches off. Remains in standby when cold.
• Line transistor blown after a few hrs.
• TL19 (S2000 AF) is S/C after switch on.
• Rainbow effect on top of screen. (6205IMCNIC tip from NORDMENDE)
• No synchronisation. in TXT.
• Dead. (with circuit diagram extract)
• Adjusting the PAL amplitude: chassis.
• To improve operation of mute circuit.
• At switch on, the tube flashes on the loudspeaker and stops. Negative picture.
• Hyperband re-fitting.
• Channel programming and saving in SECAM mode.
• Black picture like in AV at switch on. OSD and channel display function. In AV picture ok but no reception via the aerial. No snow.
• CTV in standby one hour. After CTV does not start up from remote control or front panel. TV stops with the switch. Waits 30 mins. Starts to work again with switch. Functions ok with the remote control and front panel. (extract of circuit diagram attached)
• No brightness, only colours. Only one colour in TXT (mostly green). Loss of certain colours.
• Vertical scanning line is at bottom of screen and CTV blows. (service info for NORDMENDE -6205IMCNIC)
• Shuts down (at start-up). (part of circuit diagram displayed) (NORDMENDE - 6205IMCNIC information)
• Passes all channels without stopping.
• No horizontal synchronisation.
• Protective circuit starts up. Pulsates.
• No power supply on the uP.
• No functions. Standby LED is not visible.
• Dark screen.
• At start up crackling in the sound and arcing on the picture for a few mins then ok.
• Poor switch off of picture tube.
• Horizontal transistor fails every few days.
• Dead. LED briefly flickers twice.
• Blows fuses immediately after switching on.
• EHT S20000AF blows every three days. (NORDMENDE - 6205IMCNIC information)
• Transistor TP29 (S2000AF) fails repeatedly. (with circuit diagram extract)
• Switches off when changing picture and channel and then starts again. (+ extract of circuit diagram)
• No 30V on pin 5 of tuner in PAL SECAM. (part of circuit diagram displayed)
• At start up standby light comes on then goes off straight away. (extract of circuit diagram attached)
• No function. Reset does not react.
• Appliance switches off, when screen changes and starts up right away. (service info for NORDMENDE -6205IMCNIC)
• PSU does not always start after switch on with the control panel or the RCU. (picture attached)
• Cut off lines visible after some time.
• TV only starts up very rarely, when it does start up, RL26 smokes, the deflectors heat up and smoke, distorted picture and the colours fade.
• No direct time insertion. (picture attached)
• Standby LED flashes up at second intervals. Only functions at a reduced mains voltage. (with circuit diagram extract)
• Switches to protection mode (after start-up). (with circuit diagram extract) (6205IMCNIC NORDMENDE repair tip)
• Picture and sound disappear after a few days or even after 5-6 hours operation. Standby stays on. Switching off and on help for a while.
• No picture, light line under the picture tube. (picture attached)
• Noise in speaker power supply. Goes to standby, starts up again and after 3 minutes goes to standby.
• Line BU clicks.
• Fuse and TP29 fail repeatedly.
• Starts up in standby, perhaps when cold. Standby display ok.
• No HV. (picture attached)
• White picture with stripes. Switches off after a short while.
• No sound or picture. Slow beat of the power supply each second. The light flashes. (extract of circuit diagram attached)
• Only spot, no OSD and no channels.
• Memory loss with Canal Plus decoder.
• Dark picture. after a while.
• Siren noise in speaker.
• TL19 fails in line output stage.
• Horizontal bars on picture during operation. This is accompanied by an audible signal distorting the sound.
• Switches to protection mode. after start-up.
• Power supply starts up and switches to stand-by after a couple of seconds. (part of circuit diagram displayed)
• LED is dim or OFF.
• Occasionally loud crackling from the housing.
• The appliance stops after a few minutes then starts up again. (picture attached)
• After switch on power supply pulsates three times.
• Starts up then cuts out, starts up again every 10 secs and so on.
• CTV blown, if connector BF01 remains connected. Vertical scanning line is at bottom of screen.
• Appliance switches off and switches on again, changes channel and there are great variations in the beam current.
• Line transistor blows after 10 mins. DL11 98V instead of 200V.
• White dotted lines appear on left of picture in VHF/Band I reception.
• No vertical and horizontal amplitude. Picture shifted downwards. (+ extract of circuit diagram)
• S2055 AF in the line blows after operating for a few hours. (picture attached)
• Grey screen. No audio. OK via SCART .
• Switches to standby.
• Tripping. Red standby LED dimming on and off. (picture attached)
• Horizontal line. at bottom.
• Dark screen except for a 3cm high white streak towards the top of the screen. (picture attached)
• Line on the screen at the start. (part of circuit diagram displayed)
• No OSD display. Sound cuts out at channel switch-over. Sound OK at start up. When channels are changed using TV front control keys, channels roll over even when key released.
• Adjusting the SECAM (4,25MHz) colour carrier trap: chassis.
• No voltages on the secondaries and no light.
• No functions. via tuner. OK via SCART .
• Horizontal black bars appear on screen. Parts of TXT picture are missing. (6205IMCNIC tips)
• Vertical amplitude is too low.
• PSU does not always start after switch on via front control or RC.
• E/W correction IC (TDA4950) blown each time.
• At switch on the vertical centering is off by 2cm at the top.
• No start up. Standby light comes on.
• Comes on for a short time.
• Interference bands at the bottom of the screen.
• Hiss in audio. in UHF.
• Blue tinge in picture in SECAM, ok in PAL. Black and white picture ok. (service info for NORDMENDE -6205IMCNIC)
• Does not switch on because the protection intervenes. Regular stand-by.
• The TV starts up. A white line appears at the top of the screen. System tension: voltage is approximately 58V, and the other voltages are low.
• Red LED is lit. Slight hum from the speaker. (part of circuit diagram displayed)
• Intermittently blue picture with traces of blue flyback lines.
• No power supply secondary and no standby.
• Intermittently stripe in lower picture part.
• Screen blank. Dark picture.
• Power supply transistor S2000AF blows after operating for one hour. (+ extract of circuit diagram)
• DL13 is S/C.
• After being used for 2 to 3 weeks, the 1.6 fuse burns out when the appliance starts up.
• PSU switches off after start-up.
• Intermittent switches to standby during programme or scene change. (part of circuit diagram displayed) (service info for NORDMENDE -6205IMCNIC)
• Starts for one sec and goes into standby with a hum in the loudspeaker.
• High voltage transistor fails repeatedly.
• Blank screen. (6205IMCNIC NORDMENDE repair tip)
• Stuck in standby. Red LED dim. Possibly intermittent. (part of circuit diagram displayed)
• Arcing of line transformer and focus G2. Picture now has a large horizontal foldover from top to bottom of screen.
• Power supply does not go beyond 100V.
• Switches off and on again at random.
• EHT whistles.
• PSU attempts to start up at intervalls. LED lights.
• Black and white picture. No RGB on 41, 42, 43 of IV01. 200V on DL11 is correct. (6205IMCNIC NORDMENDE repair tip)
• OSD fades on all the colours.
• Snow in picture.
• Switches to standby. after a few minutes. Switches on by itself. after a while. (picture attached)
• Picture and sound hang up. (6205IMCNIC tips)
• PSU doesn't start up intermittently.
• PSU starts up. Whistling from speakers.
• No power supply regulation. Standby LED flashes red every single second.
• Line transformer starts up three times then nothing. LED stays red.
• S2055 blows. (NORDMENDE - 6205IMCNIC information)
• Humming on sound and the screen is dark. The appliance goes to stand-by after 2-5 minutes.
• Position of RA13 and RA15.
• Sometimes switches off by itself or does not switch on.
• Sporadically loses station memory. Analog values available, all program sites are on CH02.
• At the start of production of the new IKC2 chassis, in TVs not fitted in series with teletext, the following components have not been fitted.
• Standby light remains on at switch on. No picture, no sound, no function from RC or control panel. Slight noise from PSU as if TV trying to switch on. (6205IMCNIC tip from NORDMENDE)
• Poor sound via loudspeaker, even when adjusting volume at maximum.
• Only snow. Appliance can be controlled with RC.
• Line transistor S2000AF heats up then fails. E-W geometry ok.
• No horizontal deflection. Audio OK .
• Bright part approx 5cm high in the bottom quarter of the screen. The rest of the screen is dark. (picture attached)
• Appliance hums and does not start up. (picture attached)
• EHT starts. Line pulse then Stop. (part of circuit diagram displayed)
• Starts up one time out of ten then functions ok with a nominal voltage. The rest of the time it collapses. Start up and operation ok with the variac.
• Volume varies (intermittently).
• Vertical deflection has collapsed to a bright line in the middle of the screen.
• Adjusting the audio trap: chassis.
• Horizontal output transistor fails after start-up.
• Dead, no high voltage
• AV switching threshold for camcorders.
• Switches to standby. intermittently. (+ extract of circuit diagram)
• Humming in speaker in standby.
• Switches to protection mode. when cold. (6205IMCNIC tip from NORDMENDE)
• Switches on, HV appears, then switches to standby.
• Value of capacitor position CP11 (power supply). (+ extract of circuit diagram)
• Switches to protection mode (after a while). (+ extract of circuit diagram)
• Occasionally changes channel by itself, channels run through or the function band appears. Occasionally when in standby, the TV switches on all by itself. (part of circuit diagram displayed)
• No luminance, white is black.
• Dead. Power LED lit . (extract of circuit diagram attached)
• Too much EHT.
• No start-up. Poor red LED.
• Line BU blows when switching on CTV. (service info for NORDMENDE -6205IMCNIC)
• Switches off by itself. when changing channels. (+ extract of circuit diagram)
• High contrast. Strong colours.
• Starts up when in standby, sometimes when cold. Standby display normal.
• White field with flyback lines.
• When playing back a cassette previously recorded by the same VCR, colours may be lost or blue flash interference due to the PAL pulse of the TV being triggered. (6205IMCNIC tips)
• All secondary power supply voltages are doubled.
• Amplitude varies with the voltages.
• After some time, picture cuts out then returns immediately, standby light weakens but stays on, then CTV has a frizzy picture.
• Excessive brightness. Flyback lines. (extract of circuit diagram attached)
• HT starts up for 2 secs then TV goes into standby.
• No start up. Standby LED lights up. Cannot be started with the RC. (picture attached)
• No voltage.
• Crackling in the speaker at start up and at switch off including standby. Slight noise in the speaker in standby. Occasionally trips at start up.
• No start up. No display. No standby LED light. (with circuit diagram extract)
• The picture is displaced towards the top of the screen (approx. 4cm to 10cm).
• Commands performed with a delay.
• White screen with no snow. Normal sound. OSD functions. Same fault via scart. OK in RGB.
• Buzzing and chirping, then switches to standby.
• Switches off by itself. at start-up (when cold).
• Beat at startup. (6205IMCNIC tips)
• Grey screen, no sound, no video in scart output. OSD ok.
• No contrast. (6205IMCNIC tips)
• Does not start up from standby, cracking is audible and appliance switches OFF, standby LED switches off.
• No start-up. Front LED lights up then goes off.
• PSU chirps if appliance is switched on via power switch. After approx 5 secs everything is off.
• Goes into standby after reducing the frame to a horizontal line after a few mins.
• Remains in "burst" mode with a hum noise in LF.
• No switch on. Crackles faintly, no LED lit.
• Switches off immediately without becoming bright. (with circuit diagram extract)
• HT oscillates and appliance stops.
• Power supply BU blown at switch on.
• Channels scroll. Functions if control panel plate on front panel is disconnected.
• Tuned to channels but only snow. Selector does not respond to channel input. (part of circuit diagram displayed)
• After a few mins switches to standby. After some time can be switched on again from RC. (part of circuit diagram displayed)
• White horizontal line at top of screen. Rest of screen is black.
• Faulty OSD.
• No audio. when cold.
• Noise on loud speaker and the screen is black. The appliance goes to stand by after a few minutes.
• Teletext clock stops. Each 5cm high part of the picture is missing.
• Slow start-up (when cold). (extract of circuit diagram attached)
• Replacement kit of thyristor ESM740/G1/G2.
• No function, standby point is not visible.
• Line-BU TL19 (S2000AF) fails immmediately after start-up.
• Picture modulation in power function.
• No picture. OSD OK .
• Horizontal output stage does not start up. (part of circuit diagram displayed)
• No function. Initially LED indication OK.
• At switch on there is a noise and light goes out. (picture attached)
• Vertical line. (+ extract of circuit diagram)
• Switches to standby (after start-up). No RC functions. (with circuit diagram extract)
• Production mode. (6205IMCNIC tip from NORDMENDE)
• Blue picture. Blue streaking.
• Plastic effect. Does not decode Channel +.
• Wavy lines.
• Starts up but stops 2 secs later.
• Random coloured flash.
• Modification of connector on TXT IKC2-VT4P.
• No audio (intermittently). (6205IMCNIC NORDMENDE repair tip)
• PSU only works in Burst mode, the red LED does not light up. (part of circuit diagram displayed)
• Blurred picture, focus pot does not work. (NORDMENDE - 6205IMCNIC information)
• Starts up, works for 30 secs then goes into standby. Starts up again by itself after 2 mins.
• No start-up from standby with RC. (extract of circuit diagram attached)
• Vertical stage is stuck.
• Vertical lines run over the whole screen.
• No picture. (+ extract of circuit diagram)
• Poor sound quality (mono appliances). (NORDMENDE - 6205IMCNIC information)
• Channels run through, sound whistles and there are lines if picture present.
• At bottom of picture superimposition of a band similar to that of the sound level and to a yellow rectangle. (6205IMCNIC NORDMENDE repair tip)
• At start up, starts up then stops. Standby light remains lit.
• No tuning, maximum tuning voltage.
• Dark picture. No audio. OSD OK .
• Vertical fault. Black screen.
• White screen, no picture. Sound ok on all channels. Same via scart.
• Occasionally fails for a short time (Occasionally does not function for days). (picture attached)
• Only a horizontal line in middle of picture.
• Dull picture. No contrast control.
• Intermittently switches off and on when changing channels or when picture has high beam current content.
• Line transformer is often defective. (extract of circuit diagram attached)
• When warm picture and sound increase then switches into standby. (+ extract of circuit diagram)
• Shut down protective circuit.
• Dead. Intermittently OK from cold.
• No TXT (intermittently).
• Moire effect picture according to sound frequencies, on some frequencies the picture is ok for a fraction of a second. Melf RP54 is not present on the CTV chassis.
• Low supply voltages.
• Excessive horizontal size. (+ extract of circuit diagram)
• Tripping. (extract of circuit diagram attached)
• Remains in standby. Occasionally starts then goes into standby after 5 mins.
• Vertical lines are distorted horizontally. E/W equalisation can not be adjusted correctly.
• Starts up, but after 10 minutes picture is snowy and tuner sensibility decreases.
• Blows at switch on. (picture attached) (service info for NORDMENDE -6205IMCNIC)
• Incorrect speed of power supply. (part of circuit diagram displayed)
• Twinning lines at top. Vertical distorted. Becomes better after warmed up.
• Dark screen. Stretched vertical lines.
• Regulator fault. (part of circuit diagram displayed)
• Maximum luminance. (6205IMCNIC NORDMENDE repair tip)
• Screen lit up. No sound or picture. Thermal noise in the sound and snow. No function via RC or control panel (+ extract of circuit diagram)
• Tripping. after a few hours. (picture attached)
• Intermittently trips off for approx 1 sec.
• Goes into safety mode. Then switches on again for 4 seconds.
• The power supply pulsates at start-up.
• Trapezium distortion on top in picture, no functions.
• Picture shows green, red and blue lines and the raster rattles audibly.
• Picture and sound distorted. Hum in PSU. (service info for NORDMENDE -6205IMCNIC)
• Hum on sound and dark screen. Goes into standby.
• Picture flickers with coloured OSD (eg from a VCR).
• Chroma fault. Intermittent coloured interference lines.
• Stops for 10 secs after 10 mins. (extract of circuit diagram attached)
• Dim picture.
• Flickering at switch on. (+ extract of circuit diagram)
• Goes into standby after a few secs. Appliance and EHT start up well at switch on.
• No sound. No line transformer and standby LED is on.
• Standby light on, no start up of power supply.
• HV and U-sys too low.
• EHT collapses.
• Vertical bars. on the left.
• Excessive horizontal size. at top. Reduced horizontal size. at bottom.
• No start-up. (part of circuit diagram displayed)
• Vertical rainbow zones over the picture right over the width of the screen. Intermittent fault.
• Distortion, white flags on the left side of the picture. Sometimes negative picture. (part of circuit diagram displayed)
• Arcing in picture. at top.
• Chroma fault occurs although the tuning discriminators and the grey scale function correctly.
• FP01 and TP29 blow at Power On. (extract of circuit diagram attached)
• Vertical stability fault. (extract of circuit diagram attached)
• Collector of the line line output transistor disconnects when soldered. (+ extract of circuit diagram)
• Picture is displaced towards bottom of screen (approx. 5cm to 15cm).
• In breakdown mode with 2.2K, pin 20 and 32 have been removed, EHT but 300V pulsates instead of 600 or 700V. 100V at the start of video but everything collapses if you refit DL13.
• PSU does not start up correctly. Standby LED flickers
• White screen with a line in diagonal. Audio OK.
• No picture. No sound. Insufficient width. Picture has a 5cm band at top of screen.
• After switch on, vertical centering is shifted intermittently upwards approx. 2 cm; it goes to normal position after approx. 10 minutes.
• No picture content. Picture becomes increasingly bright with flyback lines. Switches to safety mode.
• At switch on, the appliance goes to stand by. After trying to start several times the TP19 and TP29 are damaged.
• At start up line transformer powers up then appliance goes into standby.
• Blows on a white picture. Power supply as new.
• No power supply regulation.
• Picture rolls. (part of circuit diagram displayed)
• Tripping sound from flyback transformer, sometimes no picture, another time it switches itself OFF.
• Fuse (1.6A) blows intermittently. (extract of circuit diagram attached)
• Adjusting the peak white: chassis.
• Amplitude and/or alignment vary intermittently.
• The power supply starts up jerkily but occasionally does not start up at all. (picture attached)
• TT switches on automatically.
• No power supply. No standby on front panel. (picture attached)
• No start up. Faint whistling on loudspeaker.
• At switch on slight line crackling and no start up. Red LED ok. (part of circuit diagram displayed)
• No NS correction.
• Occasional crackling effect on the video signal.
• Repeated failure of chopper transistor TP29 (BUH515). (part of circuit diagram displayed)
• S2000 fails. (6205IMCNIC NORDMENDE repair tip)
• When pressing the switch the standby light comes on a little then goes off. (part of circuit diagram displayed)
• Channels run through and do not stop.
• Picture starts off very bright and after few secs goes dark.
• S2055 defective after switch-on.
• Three white lines at the top of the picture, nothing else. (+ extract of circuit diagram)
• North/South correction cannot be adjusted correctly. (part of circuit diagram displayed)
• Line does not oscillate.
• TL19 (S2000AF) fails repeatedly.
• The display is incorrect.
• Intermittently shuts down briefly (sometimes after two hours).
• TV functions, thermal tube noise on the screen but no picture. RCU does not work. Dark display, a channel is displayed, programme nos run through and stops on AV. No sound.
• White line. at top.
• CTV remains in standby. HT at 127V, 15V at 9V, 28 at 20.
• Setting the main voltage (Usyst. 110V): Chassis. (+ extract of circuit diagram)
• Picture only in top part of screen. (+ extract of circuit diagram)
• White line, slightly tilted at the bottom of the screen.
• At switch on, control panel LED remains red and flickers faintly.
• Switches to standby. when changing channels.
• Black screen. Channel 0 display on video.
• Switches to standby. after start-up. (6205IMCNIC tip from NORDMENDE)
• Line output transistor overheats. (+ extract of circuit diagram)
• Does not stay on AV, switches sporadically back to HF programme site.
• Blurred picture which occasionally becomes normal again.
• Poor audio.
• Dark picture (after a while).
• Line frequency drifts slightly.
• Goes to standby at switch-on. Trips slowly if programme button held on. (picture attached)
• No OSD. (part of circuit diagram displayed)
• Snowy picture. No reception in channel search.
• Impossible to display the PAL SECAM standards. (with circuit diagram extract) (6205IMCNIC NORDMENDE repair tip)
• Only noise.
• Slight raster distortion at top or bottom of screen, depending on defective diode.
• Fuse blows at switch on. (with circuit diagram extract)
• Loses programmes from memory at irregular intervals.
• TV starts up well but with a lot of noise.
• At switch on everything seems to be starting up well, EHT is established then 3 secs after the line oscillation is interrupted. 7V is now 13V and stays there. TV is apparently in stand by. (extract of circuit diagram attached)
• Standby LED is still lit up. Horizontal white stripe. (+ extract of circuit diagram)
• Dark screen and the RL11 is open circuit.
• No function from RC, ok from front panel. RC receiver ok. (+ extract of circuit diagram)
• Stops intermittently. LED remains red. TV does not start up again with the channel button. Necessary to press the standby button then the channel button. (part of circuit diagram displayed)
• No picture. Loss of one or more colours.
• Switches to standby (after start-up). (part of circuit diagram displayed)
• Picture is dark, screen menu ok.
• Picture is slightly displaced towards bottom of screen.
• Horizontal white line. at bottom.
• No colour (intermittently). (with circuit diagram extract) (6205IMCNIC NORDMENDE repair tip)
• High contrast.
• On the CRT board TT33 is S/C for the second time in a month.
• After changing FBT twice, light varies when you turn focus pot; FBT ok, after a few moments light decreases at switch on, light picture with G2 set to minimum then darkens.
• Slight reduction of raster amplitude.
• Flag effect when playing back with a VPH6400 Thomson VCR. Ok via scart.
• Does not start up. Remains in AV. When in standby, whistling from speaker. (extract of circuit diagram attached)
• Horizontal line on a third of the picture towards the top. (with circuit diagram extract) (service info for NORDMENDE -6205IMCNIC)
• No picture. via SCART. Audio and HV OK .
• Crackling in picture and sound, even in VHF.
• Difficulty switching on at a high temperature (40°C). You can no longer switch on the appliance with the RC. (with circuit diagram extract)
• Vertical foldover at top. Dark picture. (part of circuit diagram displayed)
• No sawtooth signal on raster. Horizontal bar appears at bottom of picture.
• Switches to protection mode (after a few seconds).
• Horizontal size varies. depending on picture content.
• PSU goes into safety mode.
• PSU pulsates every second and the standby light flashes.
• Appliance shuts down, then restarts. (part of circuit diagram displayed)
• Incorrect picture height. Black 5cm bar at bottom, black 2cm bar at top of picture.
• No picture, only snow. (with circuit diagram extract)
• Remains blocked on CH15 and PR8 at start up. Occasionally CTV functions normally.
• Picture shrinks and a white band appears at bottom of screen after a short period of time.
• Following a fault on the line there is no colour. Composite video is ok on 53 of IV01 but there is no RGB on 41, 42 and 43.
• Streaky luminance and flyback lines.
• Zigzag pattern across whole screen.
• Line power transistor S2055AF blows immediately after being replaced. (part of circuit diagram displayed)
• Excessive green.
• Adjusting the bell filter: chassis.
• Power supply pumps every single second. (6205IMCNIC NORDMENDE repair tip)
• Vertical sync bar in the middle of the screen. (with circuit diagram extract)
• Vertical lines shake. In top third of the screen picture tearing is greater.
• Starts up with difficulty. Line transformer only starts up after several attempts. (6205IMCNIC tip from NORDMENDE)
• Intermittent fault especially when cold. No vertical stability. No luminance for a few seconds then everything OK.
• Vertical jitter. (service info for NORDMENDE -6205IMCNIC)
• Switches on. Red LED lights, but turns darker after start-up. No start-up via RC. (extract of circuit diagram attached)
• Dark screen, sound OK. Nothing in scart nor in RGB.
• US voltage increases, CTV stops.
• Faint sound although correct. (6205IMCNIC tips)
• S2000 blown.
• Picture is OK although raster has moved up. (+ extract of circuit diagram)
• Does not start up. Ok if power supply is 110V. Normal scanning.
• Vertical lines. (extract of circuit diagram attached)
• At switch on, front LED flashes irregularly or remains fixed. (part of circuit diagram displayed) (6205IMCNIC tips)
• TP29 has a short circuit and FP01 blows after a short time.
• No voltage at secondary.
• PSU only works in standby; no switch on. (part of circuit diagram displayed)
• Saving new basic adjustments such as brightness.
• Line transformer blows a few secs later after appliance is started up, line transformer has been changed but fault persists. Output voltage 8.2V instead of 15V on the power supply secondary with the line transformer removed.
• Power supply fuse blows at switch on. Everything seems ok.
• No picture. via tuner. OK via SCART . (6205IMCNIC NORDMENDE repair tip)
• Intermittently picture has no contrast and has a blue tinge. Sound ok.
• Does not start up. Standby lit. Slight motor noise in speaker.
• Trips erratically.
• Adjusting the NTSC(3,58MHz) colour carrier trap: chassis.
• Noise in the HP power supply. The appliance goes to stand-by and starts up again. Dark screen and after 3 minutes the appliance returns to stand-by.
• Functions for a few secs then goes into safety mode. Functions without the raster deflector.
• No voltages at the secondary of LP36. Standby light on.
• Programmed on channels but still only snow. Selector does not react on channel inputs.
• East/West amplitude changes with the beam current.
• Only a palm high picture at bottom of screen. (service info for NORDMENDE -6205IMCNIC)
• No picture. via SCART. Audio OK .
• New transformer, TV starts up and the US voltage increases to 122V instead of 140.
• Dark picture. after warm-up. No picture. after a while.
• TL19 in the line output stage is defective. (part of circuit diagram displayed)
• Smearing in high channels.
• Does not switch on immediately when pressing switch, only after loudspeakers click 3 times and standby LED reduces brightness 3 times.
• No contrast control.
• Tripping (intermittently).
• Occasionally TV does not start up and remains in standby.
• Loud noise when switching on TV via mains. Can be intermittent.
• TP29 fails after switch on. (service info for NORDMENDE -6205IMCNIC)
• Repeated failure of BU508DF in power supply. (NORDMENDE - 6205IMCNIC information)
• Diode goes green and then switches off. CTV does not start. (with circuit diagram extract)
• No sound and no picture. Appliance remains in stand by.
• Occasionally loss of station memory. When warm stations run through from 1 to 39 without loss of station memory.
• Raster weakened after a few mins and is reduced to a horizontal lines then TV goes into standby. (6205IMCNIC tip from NORDMENDE)
• Slight raster scanning in the middle of the screen.
• No channel storing.
• Line stage does not start up. (picture attached)
• Poor audio (via SCART).
• Distorted picture. Strong streaking.
• Very dark and unstable picture at start-up but becomes normal again after quarter of an hour.
• No more line scanning possible. RL25 cuts out.
• Vertical picture has shifted to top by approx 2cm at switch on. Picture OK after approx 10 mins. (6205IMCNIC NORDMENDE repair tip)
• Fuse cuts out without apparent reason.
• Four vertical bands on top of screen.
• No horizontal deflection. (picture attached) (6205IMCNIC tip from NORDMENDE)
• White line. in the centre. (6205IMCNIC tips)
• Switches to standby (at start-up). (picture attached)
• Remains in standby. Hum in loudspeakers. (picture attached) (6205IMCNIC NORDMENDE repair tip)
• Synchronisation during PB of the VCR.
• BU 508A in the power supply gets too hot and goes defective after approx 5 minutes. (with circuit diagram extract) (service info for NORDMENDE -6205IMCNIC)
• Attempts to start then smoke appears.
• No colour. (picture attached)
• No start up. LED flashes irregularly, switches intermittently to standby.
• Adjusting the SECAM identification: chassis.
• Power supply starts up for a few secs then collapses while pumping on standby light.
• The light comes on. Power supply starts up for 1-4secs then cuts out. (6205IMCNIC NORDMENDE repair tip)
• No red.
• Starts up then stops immediately afterwards when ON/OFF switch pressed. (+ extract of circuit diagram)
• Distorted audio. intermittently.
• Goes into safety mode after operating for a few mins or hours. Necessary to wait 2 mins to start again with the RC. (with circuit diagram extract)
• Standby light switches off. (picture attached)
• Protection mode activated.
• Volume becomes louder after few mins, cannot be adjusted. (6205IMCNIC NORDMENDE repair tip)
• Sound ok in slow motion. A hum can be heard if you increase the power.
• Standby LED switched on, becomes green for an instant. No start up. Power supply sends pulses.
• No -1V at base of TP29.
• TV starts up for a few seconds with a jerky noise then stops and so on.
• Secondary voltages are low.
• The picture disappears, drifts then reappears for a few fractions of a second and then drifts again. A whistling noise can be heard when the picture reappears.
• FP01 blows. (service info for NORDMENDE -6205IMCNIC)
• After switch on, PSU fails immediately. (+ extract of circuit diagram)
• The appliance switches on at random when the remote control is used.
• Picture twitches intermittently in width and height, chriping or noise can be heard in SM transformer. (NORDMENDE - 6205IMCNIC information)
• IR01 loses memory without any apparent reason.
• Device shuts down when zapping.
• No voltage on LP36 in secondary side.
• Tripping. after a few minutes (intermittently).
• After operating for some time the channels begin to run through. Nothing occurs when the circuits are cooled down.
• Sound distorted, especially by stereo.
• HT fails immediately after starting up. PSU switches to standby.
• White picture, flyback line and too bright.
• Picture for 30 secs then white screen.
• In playback, especially with prerecorded cassettes the picture oscillates horizontally or is distorted like a flag in the top part of the screen.
• No OSD via RC or front controls. Screen is lit, snow present. No sound or picture. (part of circuit diagram displayed)
• No picture, only three lines two thirds of the way down the screen. Goes into SAFETY mode after 1 min. (extract of circuit diagram attached)
• Picture with black bands and sound whistling/tuner drift. (with circuit diagram extract)
• Power supply hiccups. (extract of circuit diagram attached)
• Luminance streaks and flyback lines.
• OSD appears on its own. Switches from stereo to mono a number of times.
• Collapses at switch on. Functions normally when first switched on
• Dark screen. Blue 1cm band at the top of the screen. No access to functions of: volume, channel, standby (no sound or picture). (with circuit diagram extract)
• 10cm frizzy lines in top part of the picture. (with circuit diagram extract)
• Picture slowly darkens. The cathode voltages are ok.
• Power supply voltage: 15V: 8V; 140: 80V. The same with the line transformer disconnected.
• Power supply transistor TP20 blows and so does the mains fuse FP01 after operating for a few mins.
• Appliance switches off if slightly shaking chassis and then starts up immediately. Occasionally drifts off tune (only snow on screen).
• The screen insertions are unsynchronised, if no aerial signal is present.
• Goes to SAFETY mode and no scanning possible.
• How to remove protection.
• Stuck in standby. (with circuit diagram extract)
• No PAL colour, either via aerial or via scart.
• Fluctuations of the picture according to the video content.
• No or intermittent start-up. when cold.
• Vertical line approx 1/3 from left of picture. Hardly visible, but annoying.
• Red picture. Flyback lines.
• After a short time the US voltage increases so that the TV cuts out.
• Modification to improve AGC adjustment.
• Chroma decoding.
• Snow in picture. in UHF.
• Audible start up when cold. Switches off after 1 sec. After switching on again, only standby LED is lit. No other functions. Raster is defective (+ extract of circuit diagram)
• Poor picture after 15 mins from start-up. Audio OK. (with circuit diagram extract)
• Picture jumps then stabilises in black and white always on the same channel out of all the channels available.
• Functions for a few secs then goes into standby. Channel change does not occur. (picture attached)
• Power supply stops.
• No RC. No sound, no channel change after changing IR receiver, with or without RC. Manual controls ok.
• No colour. via SCART.
• Pincushion distortion.
• Unstable vertical scanning with foldover in the picture. (+ extract of circuit diagram) (service info for NORDMENDE -6205IMCNIC)
• Line transformer does not start up. (picture attached)
• Does not change channels.
• Stuck in standby. LED is red . (with circuit diagram extract)
• Resistor RT04 on the picture tube base blows repeatedly. (picture attached)
• At start up standby point lights up and hum. (with circuit diagram extract)
• No TXT. (picture attached)
• Picture is just at the top edge of the CRT if the vertical picture centering regulator is at the end position. The topmost lines are somewhat bent to the right.
• Distorted picture (line amplitude, linearity).
• Transistor TP 29 short circuits after working for some time.
• Dark picture. Audio OK .
• Snow on the screen.
• Ticking, then PSU switches off.
• US voltage is 57V. If you unplug pin 3 from the line stage transformer the voltage returns to 113V. Line stage transformer has been changed. (6205IMCNIC NORDMENDE repair tip)
• Tube tries to switch on then switches off. (part of circuit diagram displayed)
• Programme number/AV symbol is permanently displayed.
• No start-up from PSU.
• Chroma lacks green.
• Use of the lithium battery.
• Power supply pumps when cold, red light flashes.
• Adjusting the UG2 screen grid voltage: chassis.
• Picture goes into PAL occasionally but the sound remains normal. Picture returns to normal after a few secs.
• Line output transformer arcing.
• Curtain effect.
• Only the LL' display functions in the Multistandard version.
• No sound and no video not even in scart. 3cm white line at top of picture. Green LED on.
• Shuts down. after start-up. (part of circuit diagram displayed) (6205IMCNIC tips)
• Power supply is dead, stand-by mode does not function.
• Regulation fault of the PSU. Standby LED flashes red every sec.