6208IMCNIC 0989531G58 / NORDMENDE [TV]

• After switch on, PSU fails immediately. (part of circuit diagram displayed)
• Switches to protection mode. (extract of circuit diagram attached)
• Picture with flyback line on one colour.
• Line output stage immediately defective after switch on. (picture attached) (6208IMCNIC tips)
• The grey scale is incorrect.
• Tuning drifts after 20 mins.
• No synchronisation. (with circuit diagram extract) (NORDMENDE - 6208IMCNIC information)
• Occasionally changes channel by itself, channels run through or the function band appears. Occasionally when in standby, the TV switches on all by itself. (part of circuit diagram displayed)
• PSU only works in Burst mode, the red LED does not light up. (extract of circuit diagram attached)
• TL19 in line output stage is defective.
• No function either from control panel nor RC. No OSD.
• Switches to standby.
• Slow start-up.
• Burst of EHT. (with circuit diagram extract) (6208IMCNIC tip from NORDMENDE)
• B/W picture in PAL. (service info for NORDMENDE -6208IMCNIC)
• Does not start up. Standby lit. Slight motor noise in speaker.
• Intermittently blue picture with traces of blue flyback lines.
• Regulation fault of the PSU. Standby LED flashes red every sec.
• No colour. via SCART.
• Maximum luminance.
• No vertical and horizontal amplitude. Picture shifted downwards. (part of circuit diagram displayed)
• Low contrast on TXT and OSGs.
• Channels run through and do not stop.
• Intermittently black band in the middle of the screen then increases in size to fill the whole of the screen. (+ extract of circuit diagram)
• S2000 fails.
• Pincushion distortion.
• Picture rolls. (part of circuit diagram displayed)
• Noise in the HP power supply. The appliance goes to stand-by and starts up again. Dark screen and after 3 minutes the appliance returns to stand-by.
• After changing FBT twice, light varies when you turn focus pot; FBT ok, after a few moments light decreases at switch on, light picture with G2 set to minimum then darkens.
• No picture at switch on. Picture appears when changing channel.
• At start up snowy screen with no reception. When pressing the programme keys the numbers run through continuously. No sound.
• Picture flickers with coloured OSD (eg from a VCR).
• Black lines on the picture. Poor sync.
• Line BU blows at once. (with circuit diagram extract)
• Blackish bar after whites.
• At switch on, the tube flashes on the loudspeaker and stops. Negative picture. (6208IMCNIC tips)
• Does not change channels.
• Power supply fault. Remains in standby. (with circuit diagram extract)
• FBT is started up by a signal but appliance does not start. In standby mode.
• S2055 AF in the line blows after operating for a few hours. (extract of circuit diagram attached) (6208IMCNIC tips)
• No synchronisation. in TXT.
• Very white lines at the top of the screen. (6208IMCNIC tip from NORDMENDE)
• Scanning at bottom of screen.
• Goes to standby at switch-on. Trips slowly if programme button held on. (extract of circuit diagram attached)
• Tripping. after a few minutes (intermittently).
• Us is too high at 121Vpp instead of 52Vpp.
• Mono sound is OK. Stereo sound scratches .
• PSU attempts to start up at intervalls. LED lights.
• No sound. No line transformer and standby LED is on.
• Intermittently stripe in lower picture part.
• Picture is OK although raster has moved up. (picture attached)
• No reception. in UHF.
• Line transistor blows after 10 mins. DL11 98V instead of 200V.
• Switches on, HV appears, then switches to standby.
• Poor sound via loudspeaker, even when adjusting volume at maximum.
• No function, standby point is not visible.
• No direct time insertion. (part of circuit diagram displayed)
• EHT S20000AF blows every three days.
• The lamp is weak.
• Horizontal black bars appear on screen. Parts of TXT picture are missing.
• No power supply on the uP. (6208IMCNIC tip from NORDMENDE)
• Memory loss with Canal Plus decoder.
• At the start of production of the new IKC2 chassis, in TVs not fitted in series with teletext, the following components have not been fitted.
• Vertical fault. Black screen.
• Occasionally there is no light at all.
• Vertical lines are distorted horizontally. E/W equalizer can not be adjusted correctly.
• No picture. via tuner. OK via SCART .
• Shuts down (intermittently). (6208IMCNIC tips)
• Power supply hiccups. (extract of circuit diagram attached)
• No RC. No sound, no channel change after changing IR receiver, with or without RC. Manual controls ok.
• Grey picture with 6 flyback lines without picture content.
• US voltage is 57V. If you unplug pin 3 from the line stage transformer the voltage returns to 113V. Line stage transformer has been changed.
• Picture vibrates in the rythme of sound.
• Set is dead but not tripping.
• Fuse fails.
• Standby LED lights up and TV switches on, then 2 or 3 lines across screen and appliance switches to standby.
• Vertical stage is stuck.
• Vertical jitter.
• Power supply does not go beyond 100V.
• Amplitude varies with the voltages.
• S2000AF in power supply is defective. Functions OK for a week, then S2000AF and primary fuse defective. (with circuit diagram extract)
• FP01 blows.
• Power supply transistor S2000AF blows after operating for one hour. (part of circuit diagram displayed)
• Only noise.
• Synchronisation during PB of the VCR.
• Vertical picture has shifted to top by approx 2cm at switch on. Picture OK after approx 10 mins.
• No start-up from standby with RC. (with circuit diagram extract) (6208IMCNIC tips)
• Vertical lines run over the whole screen.
• No picture scanning.
• With high contrast PSU trips then starts again. Occurs randomly. (picture attached)
• Random loss of station memory when CTV starts up.
• At start up standby light comes on then goes off straight away. (with circuit diagram extract)
• No OSD. (part of circuit diagram displayed)
• Vertical foldover.
• Power supply pulsates every single second. Standby LED flashes.
• Ticking, then PSU switches off.
• Blows intermittently and switches on again. (part of circuit diagram displayed)
• Occasionally loss of station memory. When warm stations run through from 1 to 39 without loss of station memory.
• Power supply BU blown at switch on.
• When 120V at variac, UL1 reaches 280V.
• Hiss in audio. in UHF.
• Dead, no high voltage
• Amplitude and/or alignment vary intermittently.
• Shuts down. after start-up. (part of circuit diagram displayed)
• Picture breaks up and crackles on sound.
• Blue tint in picture intermittently.
• White picture with stripes. Switches off after a short while.
• Dead. No voltage on the secondary. 300V on collector TP29. All the transistors and diodes are ok. Even no standby light.
• Picture bright, dark or faint with flyback lines.
• Stops for 10 secs after 10 mins. (+ extract of circuit diagram)
• Hyperband re-fitting.
• Switches to standby. after start-up.
• Screen is dark. Slight noise from the line output transformer. (6208IMCNIC tip from NORDMENDE)
• 10cm frizzy lines in top part of the picture. (picture attached)
• No horizontal deflection. (extract of circuit diagram attached)
• Appliance in burst mode. No standby light.
• Switches to standby. in PB.
• Smearing in high channels.
• Twinning lines at top. Vertical distorted. Becomes better after warmed up. (6208IMCNIC tip from NORDMENDE)
• At switch on, front LED flashes irregularly or remains fixed. (part of circuit diagram displayed)
• No start up of power supply. No standby light. No noise.
• No functions. Standby LED is not visible.
• No start-up (when cold). (picture attached)
• Short line pulses on the line output collector and then dead. (picture attached)
• No picture or OSD information. RC and front panel do not function. (NORDMENDE - 6208IMCNIC information)
• TL19 fails in line output stage.
• At start up functions normally for 20 to 50 secs then goes into standby prematurely. (+ extract of circuit diagram)
• Memory loss or random deprogramming of uP.
• Defective picture, poor colour and white dot at switch off.
• Blurred picture which occasionally becomes normal again. (service info for NORDMENDE -6208IMCNIC)
• Siren noise in the speaker.
• Goes to SAFETY mode and no scanning possible.
• After being used for 2 to 3 weeks, the 1.6 fuse burns out when the appliance starts up.
• TV does not start up or stops.
• Blows fuses immediately after switching on.
• Impossible to go into standby via the front panel or the RC. Starts up at switch on with the red light lit. (picture attached)
• Line transistor blown after a few hrs.
• Two black bars in TXT.
• Blows on a white picture. Power supply as new.
• Switches to standby. after a few seconds. (with circuit diagram extract)
• No or intermittent start-up. when cold.
• Vertical rainbow zones over the picture right over the width of the screen. Intermittent fault.
• At switch on colour is delayed.
• At switch on, the appliance goes to stand by. After trying to start several times the TP19 and TP29 are damaged.
• Line scan transistor is in S/C.
• No power supply regulation. Standby LED flashes red every single second.
• No picture. Audio OK . (6208IMCNIC NORDMENDE repair tip)
• No picture. via SCART. Audio and HV OK .
• No power supply secondary and no standby.
• Line output S2000 fails after a while.
• Standby LED flashes bright and dark. (NORDMENDE - 6208IMCNIC information)
• Unstable picture.
• No picture. (+ extract of circuit diagram)
• No contrast control.
• Vertical scanning line is at bottom of screen and CTV blows. (service info for NORDMENDE -6208IMCNIC)
• Standby light remains on at switch on. No picture, no sound, no function from RC or control panel. Slight noise from PSU as if TV trying to switch on.
• Instructions for repairing the PSU. (+ extract of circuit diagram)
• Reduced vertical size. (with circuit diagram extract)
• Raster weakened after a few mins and is reduced to a horizontal lines then TV goes into standby. (NORDMENDE - 6208IMCNIC information)
• Stops intermittently. LED remains red. TV does not start up again with the channel button. Necessary to press the standby button then the channel button. (part of circuit diagram displayed) (service info for NORDMENDE -6208IMCNIC)
• The appliance stops after a few minutes then starts up again. (picture attached)
• Power supply S2000 blows approx every 10 hours.
• Colour fault.
• At switch on slight line crackling and no start up. Red LED ok. (with circuit diagram extract)
• TV starts up well but with a lot of noise.
• Switches to standby. when changing channels.
• Loses programmes from memory at irregular intervals. (NORDMENDE - 6208IMCNIC information)
• Excessive brightness. Flyback lines. (part of circuit diagram displayed)
• Reduced horizontal deflection.
• Vertical lines shake. In top third of the screen picture tearing is greater.
• At start up there is a power supply fault. TP29 must be replaced. After this the picture lacks vertical and horizontal amplitude. Reduced picture which has shifted to the bottom of the screen. (part of circuit diagram displayed)
• After 5 mins a noise like rapid crackling occurs at the scanning level. Noise disappears if picture is misframed upwards. (extract of circuit diagram attached) (6208IMCNIC tip from NORDMENDE)
• No audio. when cold.
• No EHT. Black screen.
• Picture is green, red and blue with flyback lines. (6208IMCNIC tip from NORDMENDE)
• Snow in picture.
• Line transformer is often defective. (+ extract of circuit diagram)
• No colour. (picture attached)
• Tripping. Standby LED flashes .
• Channels run through, sound whistles and there are lines if picture present. (6208IMCNIC NORDMENDE repair tip)
• Distortion, white flags on the left side of the picture. Sometimes negative picture. (extract of circuit diagram attached)
• No channels.
• The light comes on. Power supply starts up for 1-4secs then cuts out. (NORDMENDE - 6208IMCNIC information)
• Dark picture. after a while.
• TV functions, thermal tube noise on the screen but no picture. RCU does not work. Dark display, a channel is displayed, programme nos run through and stops on AV. No sound.
• Line transformer starts up then stops.
• Picture position shifts vertically by approx 2cm towards the top of the screen intermittently. Position returns to normal after approx 10 mins.
• Switches to standby (after a while). (+ extract of circuit diagram) (6208IMCNIC tips)
• The picture is displaced towards the top of the screen (approx. 4cm to 10cm).
• TV stops and starts up again immediately. Standby light is on.
• Blue fails - occasionally blue flyback lines visible.
• EHT starts. Line pulse then Stop. (extract of circuit diagram attached) (6208IMCNIC tip from NORDMENDE)
• At start up crackling in the sound and arcing on the picture for a few mins then ok.
• Intermittent fault especially when cold. No vertical stability. No luminance for a few seconds then everything OK. (service info for NORDMENDE -6208IMCNIC)
• No start-up. Poor red LED.
• Shuts down.
• Streaky luminance and flyback lines.
• Fuse and TP29 fail repeatedly.
• HV starts up for 3-5 secs then shuts down. (part of circuit diagram displayed)
• No memory during programming.
• No colour (via SCART).
• Dark screen and the RL11 is open circuit.
• Switches to standby. intermittently. (+ extract of circuit diagram)
• TP29 has a short circuit and FP01 blows after a short time.
• When switched on, line transformer attempts to start up then goes to standby. (extract of circuit diagram attached)
• Does not switch on immediately when pressing switch, only after loudspeakers click 3 times and standby LED reduces brightness 3 times.
• Starts up with difficulty. Line transformer only starts up after several attempts. (6208IMCNIC tips)
• LED is dim or OFF.
• White horizontal line at top of screen. Rest of screen is black.
• Horizontal collapse. (extract of circuit diagram attached)
• Power supply fuse blows at switch on. Everything seems ok.
• US voltage increases, CTV stops.
• Signals reduced to quarter of their size and are distorted on TL19 after 3 secs from start-up. TL19 burns if left under load. (+ extract of circuit diagram)
• No sawtooth signal on raster. Horizontal bar appears at bottom of picture.
• TP29 and TL19 fail after operating for 1 hr. (part of circuit diagram displayed)
• RL27 burnt.
• Picture with red as the predominant colour and flyback line apparent on the screen.
• Under certain conditions (static discharge etc.) may revert to factory set up mode.
• No horizontal deflection. Audio OK .
• No TXT. (part of circuit diagram displayed)
• Sometimes switches off by itself or does not switch on.
• Dark picture. after warm-up. No picture. after a while.
• Dull picture. No contrast control.
• PSU function description.
• Line in centre of picture.
• No start up. LED flashes irregularly, switches intermittently to standby. (service info for NORDMENDE -6208IMCNIC)
• Picture is dark, screen menu ok.
• Picture pulling on bright scenes.
• Switches on. Red LED lights, but turns darker after start-up. No start-up via RC. (picture attached)
• Vertical lines run over the top part of the screen.
• Compressed vertical. Extremely dark picture, more on the right than on the left.
• Line output transistor overheats. (part of circuit diagram displayed)
• No colour (when switching).
• Appliance switches off, when screen changes and starts up right away.
• PSU goes into safety mode.
• Functions for a few secs then goes into standby. Channel change does not occur. (extract of circuit diagram attached)
• Remains blocked on CH15 and PR8 at start up. Occasionally CTV functions normally.
• Black screen. Channel 0 display on video. (NORDMENDE - 6208IMCNIC information)
• Slight reduction of raster amplitude. (6208IMCNIC tips)
• No colour (after a while).
• Dark screen, sound OK. Nothing in scart nor in RGB.
• Picture only in top part of screen. (extract of circuit diagram attached)
• Too much EHT.
• White screen with no snow. Normal sound. OSD functions. Same fault via scart. OK in RGB. (NORDMENDE - 6208IMCNIC information)
• Adjusting the SECAM (4,25MHz) colour carrier trap: chassis. (6208IMCNIC tip from NORDMENDE)
• Line transformer does not start up. (+ extract of circuit diagram)
• Only the LL' display functions in the Multistandard version.
• One colour missing.
• No light. Poor picture. Occasional horizontal tearing. If G2 is pushed in as far as it will go picture is better. Varies from 100 to 950V, 90 degree model, 114V on DP50.
• Picture modulation in power function.
• US (110V 90º - 143V 110º) goes high after a few mins and TV trips.
• Picture slowly darkens. The cathode voltages are ok.
• Grey screen, no sound, no video in scart output. OSD ok.
• Picture starts off very bright and after few secs goes dark.
• No audio (intermittently).
• No start-up (intermittently). (+ extract of circuit diagram)
• Normal sound, white screen, no picture, flyback lines. Impossible to reduce the brightness.
• Switches to protection mode. after a few seconds.
• HV and U-sys too low.
• Picture is just at the top edge of the CRT if the vertical picture centering regulator is at the end position. The topmost lines are somewhat bent to the right.
• No start up of PSU. Low ticking. (picture attached)
• Fuse cuts out without apparent reason.
• White screen in scart and no sound. Picture ok via tuner. Displays programmes and sound level etc.
• Switches to standby (intermittently). (picture attached)
• Repeated failure of chopper transistor TP29 (BUH515). (with circuit diagram extract)
• Standby LED switched on, becomes green for an instant. No start up. Power supply sends pulses.
• Intermittently picture has no contrast and has a blue tinge. Sound ok.
• In playback, especially with prerecorded cassettes the picture oscillates horizontally or is distorted like a flag in the top part of the screen. (6208IMCNIC tips)
• Sound ok in slow motion. A hum can be heard if you increase the power.
• Black picture like in AV at switch on. OSD and channel display function. In AV picture ok but no reception via the aerial. No snow.
• No raster signal on pin 31 of IV01. (6208IMCNIC tips)
• Snowy picture. No reception in channel search.
• U/Syst voltage is 106V. (picture attached)
• When warm picture foldover towards the bottom and horizontal flyback lines. Noise from the line transformer. (with circuit diagram extract)
• Intermittently trips off for approx 1 sec. (NORDMENDE - 6208IMCNIC information)
• White stripe at the top of the screen. It is 1cm high and not as wide as the screen. No picture. (6208IMCNIC tips)
• Comes on for a short time.
• Dead. (part of circuit diagram displayed) (NORDMENDE - 6208IMCNIC information)
• Intermittently PSU doesn't start up via RC and mains.
• Channel memory loss approx every fortnight. (6208IMCNIC NORDMENDE repair tip)
• White band on top of screen. Only a buzzing noise coming from loudspeaker.
• No start-up from standby. after warm-up. (with circuit diagram extract)
• TV starts up for a few seconds with a jerky noise then stops and so on.
• Shuts down (at start-up). (+ extract of circuit diagram)
• Starts up, works for 30 secs then goes into standby. Starts up again by itself after 2 mins.
• Switches to protection mode (after a while). (extract of circuit diagram attached)
• Does not pick up in UHF or in VHF.
• Only a horizontal line in middle of picture.
• Does not switch on because the protection intervenes. Regular stand-by.
• No voltages on the secondaries and no light.
• No voltage.
• No start-up from PSU.
• Bottom of raster is missing. Deflection incomplete.
• Tripping. (with circuit diagram extract)
• Dark picture. (part of circuit diagram displayed)
• No audio (via SCART). (NORDMENDE - 6208IMCNIC information)
• Switches to standby (at start-up). (with circuit diagram extract)
• No channel storing.
• 4cm vertical scanning for a few secs.
• Horizontal line. at bottom. (6208IMCNIC tips)
• No start up of PSU, sometimes intermittently.
• Power supply starts up 3 times at switch on then switches off. No picture or sound. Red LED is lit.
• No start up except at a certain temperature. Standby ok. (+ extract of circuit diagram)
• No picture, only snow. (+ extract of circuit diagram) (6208IMCNIC tip from NORDMENDE)
• FBT is s/c twice a year. On collector TL19. 1200V instead of 1000V. CL21, CL22, CL24, CL23 replaced but fault persists. US adjusted to 143V. FBT 470034-81 CTV TA6326.
• No stations found in search. Seems to have poor power supply filtering.
• Tripping sound from flyback transformer, sometimes no picture, another time it switches itself OFF.
• 3cm white line at top of picture. No sound and no video, not even in scart. Green LED on.
• Tuning drifts.
• Programme number/AV symbol is permanently displayed.
• Dark screen.
• Picture with predominant yellow/green.
• Fault at top of picture about 4cm after 30 mins.
• Humming on sound and the screen is dark. The appliance goes to stand-by after 2-5 minutes. (6208IMCNIC tips)
• Weak colour. (NORDMENDE - 6208IMCNIC information)
• Adjusting the audio trap: chassis.
• No start-up. Front LED lights up then goes off.
• No TXT (intermittently).
• Power supply crackles once then dead.
• Arcing of line transformer and focus G2. Picture now has a large horizontal foldover from top to bottom of screen. (6208IMCNIC tips)
• PSU does not strat.
• Goes into SAFETY mode and very slight hum in LF.
• Line power transistor S2055AF blows immediately after being replaced. (picture attached)
• Occasionally TV does not start up and remains in standby.
• Intermittently switches off and on when changing channels or when picture has high beam current content. (6208IMCNIC NORDMENDE repair tip)
• Contrast average value is too high. (picture attached)
• No reception. (+ extract of circuit diagram)
• How to remove protection.
• No contrast.
• Horizontal output transistor fails after start-up. (6208IMCNIC NORDMENDE repair tip)
• Line at the bottom of the screen then goes into standby.
• Intermittently blows chopper transistor.
• Black stripes on upper and lower picture edge.
• Luminance streaks and flyback lines.
• Lines appear at top of screen or interference then goes into safety mode. At present it goes into safety mode each time after 2-3 secs. (extract of circuit diagram attached)
• S2000AF blows each time appliance is plugged in. (extract of circuit diagram attached)
• No start up. Standby LED lights up. Cannot be started with the RC. (picture attached)
• Horizontal output stage does not start up. (picture attached)
• Blurred picture, focus pot does not work.
• Crackling in picture and sound, even in VHF.
• Regulator fault. (extract of circuit diagram attached)
• Modification to improve AGC adjustment.
• No voltages at the secondary of LP36. Standby light on.
• When playing back a cassette previously recorded by the same VCR, colours may be lost or blue flash interference due to the PAL pulse of the TV being triggered.
• Dark screen. Stretched vertical lines.
• Programmed on channels but still only snow. Selector does not react on channel inputs.
• Humming in speaker in standby.
• Control board CDI 2000.
• Picture is at the lower picture edge and in time becomes a line. (with circuit diagram extract)
• Teletext clock stops. Each 5cm high part of the picture is missing.
• Picture at the bottom. No contrast.
• Power supply is dead, stand-by mode does not function.
• Line on the screen at the start. (with circuit diagram extract) (6208IMCNIC NORDMENDE repair tip)
• Vertical line. in the centre.
• No voltage on LP36 in secondary side.
• HT whistles for a short time. Standby LED remains lit. Raster is defective. (picture attached)
• Starts up when in standby, sometimes when cold. Standby display normal.
• At switch on, control panel LED remains red and flickers faintly.
• No function from RC, ok from front panel. RC receiver ok. (+ extract of circuit diagram)
• The display is incorrect.
• No reception. OK via SCART .
• East/West amplitude changes with the beam current.
• Dark picture. Audio OK .
• The picture is smaller and at the bottom of the screen.
• Red LED is lit. Slight hum from the speaker. (extract of circuit diagram attached)
• Cut off lines visible after some time.
• Does not start from Standby or switches off.
• Starts up three times then goes into safety mode. (part of circuit diagram displayed)
• Distorted picture. Lines in picture.
• Picture is narrower. When making adjustments, the picture is wavy at the sides.
• Starts up then switches off. Remains in standby when cold.
• No colour during Canal Plus. (6208IMCNIC NORDMENDE repair tip)
• Dark screen with short bright flashes.
• At switch-on, vertical centering of picture offset by 2 cm towards the top of screen.
• White line, slightly tilted at the bottom of the screen.
• No picture on upper half of the screen. Small part of picture in lower half of the screen. Just a small stripe in lower screen. Appliance switches to protection mode.
• After a short time the US voltage increases so that the TV cuts out.
• EHT arcing noise.
• Vertical sync bar in the middle of the screen. (picture attached) (service info for NORDMENDE -6208IMCNIC)
• After a few mins switches to standby. After some time can be switched on again from RC. (+ extract of circuit diagram)
• Oblique lines towards the top of the screen and there may be a demagnetization fault and the demagnetization coil is ok. The PTC has already been changed.
• Stuck in standby. Hum in audio. (part of circuit diagram displayed)
• Beat at startup.
• Only snow. Appliance can be controlled with RC.
• Sound but no picture. White screen with flyback line. (6208IMCNIC tip from NORDMENDE)
• Switches off immediately without becoming bright. (picture attached)
• Standby LED flickers and PSU does not start up correctly.
• Transistor TP29 (S2000AF) fails repeatedly. (part of circuit diagram displayed)
• Intermittent goes into standby when changing channel, also sound goes up and down intermittently. (picture attached) (6208IMCNIC tip from NORDMENDE)
• The appliance goes to secondary safety mode. (with circuit diagram extract)
• In VHF range (channel 5-12) white flecks and grey haze in the picture.
• Random coloured flash.
• There is little light.
• Adjusting the SECAM identification: chassis.
• Dead. Intermittently OK from cold.
• White setting: picture tube board.
• Four vertical bands on top of screen.
• Switches off and on again at random.
• Small screen, only inner side lights up.
• Blue flash in Secam.
• TV only starts up very rarely, when it does start up, RL26 smokes, the deflectors heat up and smoke, distorted picture and the colours fade.
• No picture, light line under the picture tube. (picture attached)
• No picture. Loss of one or more colours.
• Channels scroll. Functions if control panel plate on front panel is disconnected.
• Starts up, but after 10 minutes picture is snowy and tuner sensibility decreases.
• Vertical line wavering at left hand side. (picture attached)
• AV switching threshold for camcorders.
• TV01 and TV02 are in safety mode.
• Varying light intensity of standby LED. No start up but intermittent low hum.
• No picture. No sound. Insufficient width. Picture has a 5cm band at top of screen.
• Grey screen. No audio. OK via SCART .
• Erratic start-up. No or intermittent start-up. (+ extract of circuit diagram)
• Stuck in PAL.
• Goes into safety mode. Then switches on again for 4 seconds.
• Occasionally the TV pulsates at start up.
• At switch on the light comes on. CTV starts up then cuts out,no light, crackling noise at the level of the power supply transformer. (part of circuit diagram displayed)
• 1 flyback transformer pulse then standby. If the picture appears, one time out of five there is crackling in the transformer then standby.
• Fuse blows at switch on. (extract of circuit diagram attached)
• Picture and sound hang up.
• After some time, picture cuts out then returns immediately, standby light weakens but stays on, then CTV has a frizzy picture.
• Remains in standby. Occasionally starts then goes into standby after 5 mins.
• Only a horizontal line at top of picture. (with circuit diagram extract)
• Picture twitches intermittently in width and height, chriping or noise can be heard in SM transformer.
• Volume varies (intermittently).
• After clicking and tripping a few times, power supply remains blocked in standby at switch on.
• Dead. Power LED lit . (extract of circuit diagram attached)
• Power supply voltage: 15V: 8V; 140: 80V. The same with the line transformer disconnected.
• TV switches off when changing channel and with great variations in the beam current.
• Line transformer blows a few secs later after appliance is started up, line transformer has been changed but fault persists. Output voltage 8.2V instead of 15V on the power supply secondary with the line transformer removed.
• After a few minutes the screen goes black and motor boating occurs.
• No volume control via RC.
• Horizontal white line. at bottom.
• No start up. Faint whistling on loudspeaker.
• High contrast.
• Primary power supply fails under load.
• Functions for a few secs then goes into safety mode. Functions without the raster deflector.
• No picture. OSD OK .
• Picture jumps then stabilises in black and white always on the same channel out of all the channels available.
• No functions. Standby LED lit .
• Very dark and unstable picture at start-up but becomes normal again after quarter of an hour.
• White line. at top.
• Starts up then stops immediately afterwards when ON/OFF switch pressed. (with circuit diagram extract)
• S2000 blown.
• Weak contrast.
• Vertical compression and very dark picture, more on the right than on the left.
• No function. Reset does not react.
• Picture instability depending on sound.
• With S2000 when warm, PSU cuts out, starts again, cuts out etc. (extract of circuit diagram attached)
• Hum on sound and dark screen. Goes into standby.
• Chroma fault. Intermittent coloured interference lines.
• Replacement kit of thyristor ESM740/G1/G2.
• Starts up then cuts out, starts up again every 10 secs and so on.
• No start-up. intermittently. PSU pulsates.
• No horizontal deflection. Protective circuit trips. Standby light flashes. (part of circuit diagram displayed)
• The screen insertions are unsynchronised, if no aerial signal is present.
• Crackling effect on video and echo.
• Unstable frame linearity.
• Replacing the TL19.
• No NS correction.
• Picture is somewhat noisy.
• Fails. (with circuit diagram extract)
• Protection mode activated.
• No startup. Alarm noise from loudspeakers.
• Grey scale incorrect. Yellow-green picture. High voltage on the blue cathode (170V). Voltage on the red cathode, as well as on the green, is normal (135V).
• Picture with black bands and sound whistling/tuner drift. (extract of circuit diagram attached)
• Picture is slightly displaced towards bottom of screen. (service info for NORDMENDE -6208IMCNIC)
• TL19 (S2000 AF) is S/C after switch on.
• No -1V at base of TP29.
• Switches off by itself. after a few minutes.
• White screen. Sparks between pins 6/7.
• Power supply pulsates after a frame fault.
• Picture has vertically shifted with approx. 2cm towards top after start-up. Picture ok after approx. 10 mins.
• CTV remains in standby. HT at 127V, 15V at 9V, 28 at 20. (NORDMENDE - 6208IMCNIC information)
• TT switches on automatically.
• PSU chirps if appliance is switched on via power switch. After approx 5 secs everything is off.
• Goes into protective switching. (+ extract of circuit diagram)
• Crackling noise from power supply then dead.
• Excessive horizontal size. (part of circuit diagram displayed)
• Occasionally horizontal tearing and horizontal stripes. Same faults via aerial and in scart.
• TV01 blows after operating for 30 mins. (NORDMENDE - 6208IMCNIC information)
• No colour, only on French channel "La 3".
• Small flyback line at top of screen on left side.
• Switches off immediately if vertical plug is pulled out. (+ extract of circuit diagram)
• Appliance switches off and switches on again, changes channel and there are great variations in the beam current.
• Picture shifted vertically.
• No HF reception. Snow on picture.
• No reception. EHT flashovers.
• Power supply pumps every single second.
• CTV blown, if connector BF01 remains connected. Vertical scanning line is at bottom of screen.
• Horizontal bars on picture during operation. This is accompanied by an audible signal distorting the sound.
• Switching off fault of the spot.
• FP01 and TP29 blow at Power On. (picture attached)
• Dark picture. No audio. OSD OK .
• Arcing in picture. at top.
• Distorted picture. No adjustment possible .
• Black screen. via RF output. OK via SCART .
• Power supply starts up for a few secs then collapses while pumping on standby light. (6208IMCNIC NORDMENDE repair tip)
• No channel reception after changing tuner and IF.
• Sporadically loses station memory. Analog values available, all program sites are on CH02.
• Switches off intermittently (often at programme switch).
• TV starts up for a few secs and leaves a motor noise in the speaker. By disconnecting DL13, the appliance starts up again.
• PSU pulsates every second and the standby light flashes.
• S2055 blows.
• In breakdown mode with 2.2K, pin 20 and 32 have been removed, EHT but 300V pulsates instead of 600 or 700V. 100V at the start of video but everything collapses if you refit DL13.
• Vertical foldover at top. Dark picture. (part of circuit diagram displayed)
• No horizontal synchronisation.
• Faint picture because CRT was defective.
• Only a horizontal line at bottom of picture.
• Attempts to start, then suddenly stops.
• PSU pulsates. Standby LED flashes . (with circuit diagram extract)
• No picture content. Picture becomes increasingly bright with flyback lines. Switches to safety mode.
• Poor sound quality (mono appliances).
• Field centering off-set by 2cm toward top of screen when first switched on. (part of circuit diagram displayed)
• No audio. via tuner. No picture. via tuner. OK via SCART .
• Does not start up. Ok if power supply is 110V. Normal scanning.
• Buzzing and chirping, then switches to standby.
• PSU switches off after start-up.
• No bottom of raster. Incomplete deflection.
• No TV picture and humming from loud-speaker.
• OSD appears on its own. Switches from stereo to mono a number of times.
• No picture (intermittently). AV OK .
• When set to standard adjustments the contrast value is too high.
• Appliance switches off if slightly shaking chassis and then starts up immediately. Occasionally drifts off tune (only snow on screen).
• Blows intermittently. (6208IMCNIC tips)
• PSU doesn't start up intermittently.
• At switch on everything seems to be starting up well, EHT is established then 3 secs after the line oscillation is interrupted. 7V is now 13V and stays there. TV is apparently in stand by. (part of circuit diagram displayed)
• Dark picture (after a while).
• PSU does not start up correctly. Standby LED flickers
• No vertical deflection. (picture attached)
• Distorted audio. intermittently.
• Goes into standby after a few secs. Appliance and EHT start up well at switch on.
• Does not switch to standby.
• No functions. IR01 does not accept reset.
• No sound and no video not even in scart. 3cm white line at top of picture. Green LED on.
• Power supply pumps. Standby LED flashes.
• Remains in standby. Hum in loudspeakers. (picture attached)
• When warm picture and sound increase then switches into standby. (extract of circuit diagram attached)
• Power supply chopper blows.
• Occasionally loud crackling from the housing.
• Poor start up of PSU. Occasionally starts up but sometimes does not, especially when warming up. (with circuit diagram extract)
• PSU does not always start after switch on via front control or RC.
• All the secondary voltages are low.
• Reduced horizontal size.
• Trips erratically. (6208IMCNIC NORDMENDE repair tip)
• No raster deflection. No picture, only vague light in background. Looks like coloured spot at bottom of picture.
• Slight raster distortion at top or bottom of screen, depending on defective diode.
• After an extended operating time TP01 (BUT12A) fails. (part of circuit diagram displayed)
• Wavy picture.
• Picture goes into PAL occasionally but the sound remains normal. Picture returns to normal after a few secs.
• Chopper goes short circuit; after replacement appliance functions correctly for approx 1 minute.
• Vertical deflection has collapsed to a bright line in the middle of the screen. (6208IMCNIC tip from NORDMENDE)
• Chroma fault occurs although the tuning discriminators and the grey scale function correctly.
• Line-BU TL19 (S2000AF) fails immmediately after start-up.
• Production mode.
• No picture. Excessive brightness. Retrace lines.
• E/W correction IC (TDA4950) blown each time.
• TP29 is destroyed after 30 minutes.
• Occasional memory fault when appliance is stopped by the general switch. When switched on again, appliance is deprogrammed. (part of circuit diagram displayed)
• No videotext mode.
• Switches off by itself. when changing channels. (picture attached)
• After switch on, vertical centering is shifted intermittently upwards approx. 2 cm; it goes to normal position after approx. 10 minutes.
• No PAL colour, either via aerial or via scart.
• PSU starts for a few secs then collapses while pumping on the standby point.
• No colour from aerial or scart. IC TA8559CN has been replaced. Wave peaks at MP output are correct. (NORDMENDE - 6208IMCNIC information)
• PSU only works in standby; no switch on. (extract of circuit diagram attached)
• When the focus pot is varied the brightness varies after a few minutes, the picture turns dark.
• No more line scanning possible. RL25 cuts out.
• Distorted picture (line amplitude, linearity).
• Starts up in standby, perhaps when cold. Standby display ok.
• IR01 loses memory without any apparent reason.
• No tuning, maximum tuning voltage. (6208IMCNIC tip from NORDMENDE)
• Blue picture. Blue streaking.
• TV does not start up. TV01 not in safety mode.
• No start-up. Red LED blinks. (with circuit diagram extract)
• Poor audio (via SCART).
• Starts nomally but if appliance stops after heating up for some time, TV flashes and may take a long time to start up again. (+ extract of circuit diagram)
• Colour saturation. (NORDMENDE - 6208IMCNIC information)
• Picture runs through, impossible to stabilise.
• Line frequency drifts slightly.
• Adjusting the UG2 screen grid voltage: chassis.
• Switches to protection mode. at start-up.
• Loud noise when switching on TV via mains. Can be intermittent.
• Intermittently switches off. Tapping effects. (6208IMCNIC tip from NORDMENDE)
• No signal. (6208IMCNIC tip from NORDMENDE)
• The power supply pulsates at start-up.
• No OSD via RC or front controls. Screen is lit, snow present. No sound or picture. (with circuit diagram extract)
• No power supply regulation.
• Goes into safety mode for no apparent reason, after operating for 30 mins. Starts up again from the switch. (service info for NORDMENDE -6208IMCNIC)
• The picture disappears, drifts then reappears for a few fractions of a second and then drifts again. A whistling noise can be heard when the picture reappears.
• Remains in "burst" mode with a hum noise in LF.
• No E/W correction. when cold.
• Intermittently shuts down briefly (sometimes after two hours).
• To improve operation of mute circuit.
• Functions very well via the scart socket. No UHF VHF reception. Display on the screen is correct, white screen. (extract of circuit diagram attached)
• Little or no light.
• At start up, starts up then stops. Standby light remains lit.
• Line output transformer arcing. (6208IMCNIC tips)
• Unstable vertical scanning with foldover in the picture. (with circuit diagram extract)
• Goes into safety mode after operating for a few mins or hours. Necessary to wait 2 mins to start again with the RC. (extract of circuit diagram attached)
• No picture. via SCART. Audio OK .
• Blows at switch on. (extract of circuit diagram attached)
• PSU fails immediately after start-up.
• Switches to protection mode. when cold.
• Impossible to change standard, remains in SECAM. Picture inverted in PAL.
• Stuck in standby. Red LED dim. Possibly intermittent. (extract of circuit diagram attached)
• Switches to standby (after a few seconds). (extract of circuit diagram attached)
• No start up. No display. No standby LED light. (+ extract of circuit diagram)
• TV starts up for a few secs with a jerky noise then stops and continues like this.
• Snow in picture. in UHF.
• No line drive.
• Curtain effect. (NORDMENDE - 6208IMCNIC information)
• The appliance has a dark picture.
• Picture and sound distorted. Hum in PSU.
• Sound has increased to maximum, after a moment, neither RC nor manual commands work.
• Trips. (+ extract of circuit diagram)
• Line stage does not start up. (picture attached)
• Sound and picture cut out for a second then return to normal. (extract of circuit diagram attached)
• Audible start up when cold. Switches off after 1 sec. After switching on again, only standby LED is lit. No other functions. Raster is defective (part of circuit diagram displayed)
• Vertical lines are distorted horizontally. E/W equalisation can not be adjusted correctly.
• PSU does not always start after switch on with the control panel or the RCU. (part of circuit diagram displayed)
• No brightness, only colours. Only one colour in TXT (mostly green). Loss of certain colours.
• Rainbow effect on top of screen. (service info for NORDMENDE -6208IMCNIC)
• High contrast. Strong colours.
• Picture shows green, red and blue lines and the raster rattles audibly.
• Vertical lines are jagged.
• Poor start up performance of the power supply.
• No functions. (extract of circuit diagram attached)
• Does not come on from standby, red standby light comes on. TV01 and TV02 in the protective circuit respond.
• When switching off the appliance in standby and with the mains switch there is a loud crackling in the speaker. (+ extract of circuit diagram)
• HT starts up for 2 secs then TV goes into standby.
• After changing FBT which sparks, the very high tension is ok. No light on the screen even when forcing G2 44469905.
• Occasionally small horizontal black line at the top of the screen and line transformer whistles slightly.
• Screen blank. Dark picture.
• Picture is displaced from frame towards top part of screen (approx 4cm).
• Adjusting the bell filter: chassis.
• White picture and flyback line. New FBT. S2055AF replaced by S2000AF which heats up and blows after a min. (service info for NORDMENDE -6208IMCNIC)
• Tripping (intermittently).
• Wavy lines.
• Commands performed with a delay.
• No audio. No picture. Squealing from PSU. (part of circuit diagram displayed)
• Dark stripes in picture by bright picture content. Volume display jumps. Beam spot at switch off. (6208IMCNIC NORDMENDE repair tip)
• At bottom of picture superimposition of a band similar to that of the sound level and to a yellow rectangle.
• Remains in standby or goes to standby intermittently. (NORDMENDE - 6208IMCNIC information)
• By pressing the buttons PROG + and - on the front panel the channel nos run through continuously. When disconnecting the control panel, difficulties in programming a channel. (+ extract of circuit diagram)
• White stripe on the left side of screen. (6208IMCNIC tips)
• To improve IF response.
• No picture. No sound. Switches off after 3 secs, remains in standby and has an afterglow fleck. (picture attached)
• Zigzag pattern across whole screen.
• The power supply starts up jerkily but occasionally does not start up at all. (picture attached)
• Repeated failure of HOT.
• No start up. Standby light comes on.
• Ignition on the EHT (flame). (part of circuit diagram displayed) (6208IMCNIC tip from NORDMENDE)
• No start up. No standby. (extract of circuit diagram attached) (service info for NORDMENDE -6208IMCNIC)
• Collapses at switch on. Functions normally when first switched on
• No red (intermittently).
• Picture and sound disappear after a few days or even after 5-6 hours operation. Standby stays on. Switching off and on help for a while.
• Cuts out and then starts up from time to time after working for several hours.
• Blank screen.
• At switch on starts up with severe noise in loudspeaker then stops and remains in standby.
• HT fails immediately after starting up. PSU switches to standby.
• Standby LED is still lit up. Horizontal white stripe. (extract of circuit diagram attached) (service info for NORDMENDE -6208IMCNIC)
• Intermittent switches to standby during programme or scene change. (extract of circuit diagram attached)
• Standby LED flashes up at second intervals. Only functions at a reduced mains voltage. (picture attached)
• No functions. via tuner. OK via SCART .
• Switches to standby. after a few minutes. Switches on by itself. after a while. (picture attached)
• Stuck in standby. LED lit. .
• Volume of basic adjustment is too loud.
• Safety mode comes into play.
• Noise on loud speaker and the screen is black. The appliance goes to stand by after a few minutes.
• TL19 (S2000AF) fails repeatedly.
• Poor framing.
• Picture shrinks and a white band appears at bottom of screen after a short period of time. (6208IMCNIC tip from NORDMENDE)
• Line transformer starts up three times then nothing. LED stays red.
• Stuck in standby. (+ extract of circuit diagram)
• Protective circuit starts up. Pulsates.
• No 15V.
• Device shuts down when zapping.
• After appliance has been moved, strange colours. Red has become blue and screen is affected by a mauve halo.
• Faint sound although correct.
• EHT whistles.
• Starts up in standby. Standby display ok.
• Picture has increased at the top and reduced at the bottom of screen.
• Use of the lithium battery.
• At switch on PSU goes defective.
• No sound or picture. Slow beat of the power supply each second. The light flashes. (picture attached)
• Line does not oscillate.
• Trapezium distortion on top in picture, no functions.
• Three white lines at the top of the picture, nothing else. (with circuit diagram extract)
• Occasional crackling effect on the video signal.
• Adjusting the peak white: chassis.
• No start-up (after warm-up).
• Black screen, alarm noise and orange LED.
• Slight raster scanning in the middle of the screen.
• The picture blows.
• One start-up attempt with HV,then switches to standby.
• No picture, only snow. in PIP.
• Switches on, line transformer comes on then goes into standby immediately.
• Siren noise in speaker.
• Bright picture. Flyback lines.
• S2055 defective after switch-on.
• Power supply pulsates intermittently when cold or warm.
• Line BU clicks.
• Goes into standby after reducing the frame to a horizontal line after a few mins. (6208IMCNIC NORDMENDE repair tip)
• Switches to standby (after start-up). (+ extract of circuit diagram)
• Poor switch off of picture tube. (NORDMENDE - 6208IMCNIC information)
• Coloured tinge in picture.
• Intermittently increases and decreases in size both width and height.
• Cuts out intermittently. Light becoming white before turning red. No start up with RC. (+ extract of circuit diagram)
• No power supply. No standby on front panel. (part of circuit diagram displayed) (6208IMCNIC NORDMENDE repair tip)
• Impossible to display the PAL SECAM standards. (picture attached)
• Setting the main voltage (Usyst. 110V): Chassis. (+ extract of circuit diagram)
• Volume becomes louder after few mins, cannot be adjusted. (NORDMENDE - 6208IMCNIC information)
• Occasionally wide interference lines (similar to a defective HF-cable) appear on the screen. Picture is ok via Scart.
• PSU pulsates. (+ extract of circuit diagram)
• Switches to protection mode (after a few seconds).
• Noise in speaker power supply. Goes to standby, starts up again and after 3 minutes goes to standby.
• Shuts down after 10 mins. Power LED remains lit. (extract of circuit diagram attached)
• North/South correction cannot be adjusted correctly. (with circuit diagram extract)
• Bright part approx 5cm high in the bottom quarter of the screen. The rest of the screen is dark. (+ extract of circuit diagram) (6208IMCNIC NORDMENDE repair tip)
• Switches to protection mode. intermittently. (NORDMENDE - 6208IMCNIC information)
• Low contrast. (6208IMCNIC tips)
• No switch on. Crackles faintly, no LED lit.
• No start up. PSU does not oscillate.
• Passes all channels without stopping.
• When switched on, the standby light lights up but the power supply is tripping. (picture attached)
• CTV in standby one hour. After CTV does not start up from remote control or front panel. TV stops with the switch. Waits 30 mins. Starts to work again with switch. Functions ok with the remote control and front panel. (+ extract of circuit diagram)
• Switches off when changing picture and channel and then starts again. (part of circuit diagram displayed)
• Snow on the screen.
• Appliance hums and does not start up. (part of circuit diagram displayed)
• Mini raster scanning.
• Channel programming and saving in SECAM mode.
• At switch on there is a noise and light goes out. (part of circuit diagram displayed)
• Vertical line approx 1/3 from left of picture. Hardly visible, but annoying.
• Picture width and height twitches intermittently, thereby noise or chirping can be heard in SM transformer.
• At switch on the vertical centering is off by 2cm at the top.
• BU transistor TP29 blows again.
• After operating for some time the channels begin to run through. Nothing occurs when the circuits are cooled down.
• Over-accentuated fizzling sounds.
• No HV. (part of circuit diagram displayed)
• Following a fault on the line there is no colour. Composite video is ok on 53 of IV01 but there is no RGB on 41, 42 and 43.
• Dim picture.
• The TV starts up. A white line appears at the top of the screen. System tension: voltage is approximately 58V, and the other voltages are low.
• FP01 blows at switch on.
• Slow start-up (when cold). (+ extract of circuit diagram)
• Functions for 5 mins then all the channel numbers begin to run through constantly while each time the picture comes up again and RCU does not function.
• No frame sync in PB of recent rented cassettes.
• Crackling in the speaker at start up and at switch off including standby. Slight noise in the speaker in standby. Occasionally trips at start up.
• Moire effect picture according to sound frequencies, on some frequencies the picture is ok for a fraction of a second. Melf RP54 is not present on the CTV chassis.
• Starts up one time out of ten then functions ok with a nominal voltage. The rest of the time it collapses. Start up and operation ok with the variac.
• Does not start up. Remains in AV. When in standby, whistling from speaker. (part of circuit diagram displayed)
• Flag effect when playing back with a VPH6400 Thomson VCR. Ok via scart.
• Regular ondulations on the vertical lines of a test picture. (picture attached)
• The tinge varies.
• TL19 in the line output stage is defective. (part of circuit diagram displayed)
• Line transistor S2000AF heats up then fails. E-W geometry ok.
• Plastic effect. Does not decode Channel +.
• Occasionally after switch on vertical centering is shifted up approx 2cm. Goes into normal position after approx 10 mins. (with circuit diagram extract)
• Switches off after approx 3 secs. PSU switches on with brief chirping noise and then switches off.
• Noise bar. at bottom.
• Thermal R349 O/C every 3 or 4 months. (picture attached)
• No picture, no sound, standby display dot and horizontal bars over the screen light up in display. Can only be switched on with RC.
• No voltage at secondary.
• No switch on at start up. Standby light is off. At stop light comes on weakly then goes off.
• Switches off by itself. at start-up (when cold).
• Switches off when switching channels. Only switches on again after RC switches to standby. Occasionally functions OK all evening but sometimes switches off when channel is initially changed. (picture attached)
• Black, horizontal lines in picture. (with circuit diagram extract)
• White line. in the centre.
• The power supply blows.
• TL19 becomes hot and fails after approx 15 secs.
• Interference bands at the bottom of the screen.
• Low brightness.
• Vertical bars. on the left.
• Does not start up from standby, cracking is audible and appliance switches OFF, standby LED switches off.
• No sound with a Nintendo game. Game functions on another TV. (part of circuit diagram displayed)
• No functions. after warm-up.
• Resistor RT04 on the picture tube base blows repeatedly. (+ extract of circuit diagram)
• White line. at bottom.
• No line oscillation. (part of circuit diagram displayed)
• Adjusting the PAL amplitude: chassis. (service info for NORDMENDE -6208IMCNIC)
• Incorrect speed of power supply. (extract of circuit diagram attached)
• Only noise on screen, screen menu cannot be superimposed. Appliance does not react to the RCU or to control panel commands.
• Tube tries to switch on then switches off. (+ extract of circuit diagram)
• BU 508A in the power supply gets too hot and goes defective after approx 5 minutes. (picture attached)
• Tuned to channels but only snow. Selector does not respond to channel input. (part of circuit diagram displayed) (6208IMCNIC tip from NORDMENDE)
• The PSU runs continuously.
• Stuck in standby. LED is red . (part of circuit diagram displayed)
• Distorted audio. Distorted picture. (6208IMCNIC tips)
• The appliance switches on at random when the remote control is used.
• Dark screen. Blue 1cm band at the top of the screen. No access to functions of: volume, channel, standby (no sound or picture). (part of circuit diagram displayed) (NORDMENDE - 6208IMCNIC information)
• Poor scan.
• Excessive vertical size.
• PSU starts up. Whistling from speakers. (6208IMCNIC tip from NORDMENDE)
• White field with flyback lines.
• When pressing the switch the standby light comes on a little then goes off. (extract of circuit diagram attached) (6208IMCNIC tip from NORDMENDE)
• Dark screen except for a 3cm high white streak towards the top of the screen. (extract of circuit diagram attached) (service info for NORDMENDE -6208IMCNIC)
• No OSD display. Sound cuts out at channel switch-over. Sound OK at start up. When channels are changed using TV front control keys, channels roll over even when key released. (6208IMCNIC NORDMENDE repair tip)
• Horizontal line on a third of the picture towards the top. (extract of circuit diagram attached)
• Distorted picture.
• Picture is displaced towards bottom of screen (approx. 5cm to 15cm).
• TP29 fails after switch on.
• Poor picture after 15 mins from start-up. Audio OK. (extract of circuit diagram attached)
• The channel nos run through, no sound or picture but it works in video.
• Diode goes green and then switches off. CTV does not start. (+ extract of circuit diagram)
• Can not be switched on from standby via RC.
• Screen lit up. No sound or picture. Thermal noise in the sound and snow. No function via RC or control panel (part of circuit diagram displayed) (6208IMCNIC tips)
• Starts up then goes into protection mode. Standby light on. Sound OK but no picture. Bluish screen with shadows.
• Switches off by itself. intermittently. Standby LED lit .
• No colour (intermittently). (part of circuit diagram displayed)
• No luminance, white is black.
• Shut down protective circuit.
• Occasionally no scanning is possible.
• Vertical collapse. (+ extract of circuit diagram)
• Tripping. after a few hours. (with circuit diagram extract)
• Poor E/W correction. Adjustment of the amplitude is ok. (with circuit diagram extract)
• Appliance works only in Burst mode. Red LED flashes.
• Vertical line. (part of circuit diagram displayed)
• Pumps.
• EHT collapses.
• No sound or picture. Standby light switches on and goes off in a regular rhythm. (extract of circuit diagram attached)
• TP29 blows occasionally at start up or after operating for some time.
• No start-up. LED blinks .
• Collector of the line line output transistor disconnects when soldered. (+ extract of circuit diagram)
• Standby light switches off. (picture attached)
• Adjusting the R-Y demodulator: chassis.
• Excessive green.
• No picture. at bottom.
• No start up of line transformer.
• Dead. LED briefly flickers twice.
• No scanning.
• PSU fails immediately after switch on.
• No sound and no picture. Appliance remains in stand by.
• Menu display is in a wrong language.
• When cold picture is very white with flyback lines and hum in sound.
• On the CRT board TT33 is S/C for the second time in a month.
• Secondary voltages are low.
• Only a palm high picture at bottom of screen.
• Dark picture. Can only be slightly adjusted.
• The appliance fails, no picture, no sound, base raster or horizontal lines.
• No line output funtion. OK at switch on.
• To improve alignment.
• Pulsates if TV is started up after being put into standby.
• Red picture. Flyback lines.
• All secondary power supply voltages are doubled. (6208IMCNIC NORDMENDE repair tip)
• Attempts to start then smoke appears.
• Shuts down. at start-up.
• Shuts down. intermittently. (part of circuit diagram displayed)
• No start up. No U1 47V, U2 5V voltages. (service info for NORDMENDE -6208IMCNIC)
• New transformer, TV starts up and the US voltage increases to 122V instead of 140.
• Horizontal transistor fails every few days.
• No start-up. (+ extract of circuit diagram)
• White screen with flyback line or no brightness. (6208IMCNIC tip from NORDMENDE)
• Trips. after a few minutes.
• Tripping. Red standby LED dimming on and off. (picture attached)
• No start-up. LED is red .
• No start-up from standby. (with circuit diagram extract)
• Goes into safety mode when first switch on. (6208IMCNIC tip from NORDMENDE)
• At start up line transformer powers up then appliance goes into standby.
• Grey adjustment: picture tube board.
• Switches to protection mode (after start-up). (extract of circuit diagram attached) (6208IMCNIC NORDMENDE repair tip)
• At start up standby point lights up and hum. (part of circuit diagram displayed)
• Picture for 30 secs then white screen.
• Blows fuses.
• Vertical picture position shifts intermittently upwards approx 2 cm after switch on. It is OK after approx 10 mins.
• Green picture. No contrast. (extract of circuit diagram attached) (6208IMCNIC tip from NORDMENDE)
• Poor audio.
• Red raster. Horizontal lines. (6208IMCNIC tips)
• No manual or RCU command. Blocked on one channel, OSD apparent, sound present. (+ extract of circuit diagram)
• E/W correction cannot be changed.
• Trapezoid picture.
• Chroma decoding.
• Arcing with sparks and cracking sounds.
• Occasionally fails for a short time (Occasionally does not function for days). (part of circuit diagram displayed)
• Vertical lines. (+ extract of circuit diagram)
• Power supply pumps when cold, red light flashes.
• Value of capacitor position CP11 (power supply). (+ extract of circuit diagram)
• No brightness and incorrect OSD. OSD background is bright red. (extract of circuit diagram attached)
• Distorted picture. Strong streaking.
• Standby light lights up for 2 seconds then goes off. Appliance does not start up.
• Switches on but no user controls from front control panel nor from RC. Does not even switch to FF.
• Pale grey screen with fine horizontal line and hum at start up of the line transformer. (part of circuit diagram displayed)
• OSD fades on all the colours.
• Adjusting the NTSC(3,58MHz) colour carrier trap: chassis.
• Noise bar. after a few minutes.
• Starts for one sec and goes into standby with a hum in the loudspeaker.
• Power supply transistor TP20 blows and so does the mains fuse FP01 after operating for a few mins.
• Transistor TP 29 short circuits after working for some time.
• Black and white picture. No RGB on 41, 42, 43 of IV01. 200V on DL11 is correct.
• Coil LG08 (situated in the corner near the EHT) burns. (extract of circuit diagram attached)
• Switches to standby (after start-up). No RC functions. (extract of circuit diagram attached)
• Vertical foldover at bottom.
• White screen with a line in diagonal. Audio OK. (service info for NORDMENDE -6208IMCNIC)
• Saving new basic adjustments such as brightness.
• Occasionally static discharge.
• Position of RA13 and RA15.
• Picture jitters. in TXT. (with circuit diagram extract)
• No start up of line transformer and LED pulsates slightly.
• Modification of connector on TXT IKC2-VT4P.
• No picture, only three lines two thirds of the way down the screen. Goes into SAFETY mode after 1 min. (with circuit diagram extract)
• Line BU blows when switching on CTV.
• HT oscillates and appliance stops.
• Power supply starts up and switches to stand-by after a couple of seconds. (picture attached)
• Faulty OSD.
• Secondary protective circuit TV01 and TV02 disconnects intermittently. (6208IMCNIC tip from NORDMENDE)
• Power supply goes to standby and standby light is lit up.
• PSU does not always start up (start up difficulties). (part of circuit diagram displayed)
• Starts up at switch on with the red light lit. Impossible to go into standby via the control panel or RC. (+ extract of circuit diagram)
• Occasionally sound and video drift on channel 64. Operation is good on the other channels.
• Only spot, no OSD and no channels.
• Switchover to another program site is not carried out.
• Fuse (1.6A) blows intermittently. (+ extract of circuit diagram)
• High voltage transistor fails repeatedly.
• Incorrect oscillations on line BU (S2055).
• Blue tinge in picture in SECAM, ok in PAL. Black and white picture ok.
• In stand-by the light does not light up and the TV does not come on again.
• After switch on power supply pulsates three times.
• Vertical stability fault. (extract of circuit diagram attached)
• Standby light on, no start up of power supply.
• Switches on but switches off after a few mins. Intermittently switches off immediately.
• White dotted lines appear on left of picture in VHF/Band I reception.
• Fluctuations of the picture according to the video content.
• Repeated failure of BU508DF in power supply.
• Dead (intermittently).
• Picture is displaced slightly towards top of screen.
• Switches to protection mode. after start-up.
• No 30V on pin 5 of tuner in PAL SECAM. (part of circuit diagram displayed) (NORDMENDE - 6208IMCNIC information)
• DL13 is S/C.
• Starts up but stops 2 secs later.
• Does not find channels or finds one channel tuned incorrectly.
• Incorrect picture height. Black 5cm bar at bottom, black 2cm bar at top of picture.
• Chroma lacks green.
• Excessive horizontal size. at top. Reduced horizontal size. at bottom.
• Difficulty switching on at a high temperature (40°C). You can no longer switch on the appliance with the RC. (with circuit diagram extract)
• Horizontal size varies. depending on picture content.
• White screen. Flyback lines.
• Low supply voltages.
• TDA8178 heats up too much and blows.
• Appliance shuts down, then restarts. (extract of circuit diagram attached) (service info for NORDMENDE -6208IMCNIC)
• At switch on, standby light flashes once and cuts out.
• White picture, flyback line and too bright.
• Tripping. Power LED lit . (part of circuit diagram displayed)
• White screen, no picture. Sound ok on all channels. Same via scart.
• Blank raster.
• E/W correction can only be poorly adjusted. (part of circuit diagram displayed)
• Vertical amplitude is too low.
• No function. Initially LED indication OK.
• Power supply stops.
• White screen. Audio OK .
• Sound distorted, especially by stereo.
• Does not stay on AV, switches sporadically back to HF programme site.
• Flickering at switch on. (part of circuit diagram displayed)
• Works for 10 secs then goes into standby. TV ok after switching off then on again.
• No red.
• Fuse FP2 (630mA) blows.