6408IMC 991661A / NORDMENDE [TV]

• There is constantly a red "P" present on the screen.
• Intermittently image rolling, vertical sync jitter and if program switch intermitently two programs are overjumped. (part of circuit diagram displayed)
• No E/W correction. No E/W phase and amplitude control.
• No tele dialog display with front control or RC. (with circuit diagram extract)
• Adjusting the deflection- and geometry values.
• After turning on TL19 (S20AF) is destroyed immediately. (+ extract of circuit diagram)
• No N/S correction.
• No tele dialog display via control panel or RC.
• No sound. Via scart socket sound OK. Then it can be adjusted properly. (part of circuit diagram displayed)
• Video output stage IC (TEA5101A) on CRT board is defective. (with circuit diagram extract)
• TL19 (S20AF) fails immediately after replacement. (6408IMC tip from NORDMENDE)
• Dead.
• Intermittent change-over between STEREO and mono on channel 22 (ZDF) during STEREO reception.
• Part no. info: PSU repair kit.
• When switching back goes into standby and a chirping noise from loudspeakers. (part of circuit diagram displayed)
• No E/W equalisation.
• Bright horizontal line in image centre and no vertical deflection. (with circuit diagram extract)
• Vertical lines. (6408IMC tip from NORDMENDE)
• Linearity fault. Too high image amplitude. E/W distortion cannot be adjusted. (picture attached)
• Three faint dark lines on right side of picture via AV input without a signal. (extract of circuit diagram attached)
• No Tele-Dialog OSD via RC and user control.
• Adjusting the screen grid voltage: Chassis.
• Oversized OSD or OSD has shifted to the right.
• Intense side noises from flyback transformer and appliance switches to standby.
• Grey adjustment: CRT board.
• Reliability of TP29.
• HF noise and no image. (part of circuit diagram displayed)
• Linearity fault. Too high image amplitude. E/W equalisation not adjustable. (part of circuit diagram displayed)
• TL19 (S20AF) is destroyed immediately after switch on
• Adjusting the PAL amplitude: chassis.
• No switch on. Standby LED on and standby power supply ok. (picture attached)
• No switch on. Appliance in safety mode. Standby dot flashes. (extract of circuit diagram attached)
• Setting the Secam identification: chassis.
• Bright, horizontal line in the middle and no vertical deflection
• No start-up from standby. LED remains lit approx 3-4 seconds, then goes dark.
• Appliance cannot be turned on, not even from standby. (part of circuit diagram displayed)
• Intermittently image rolling, vertical sync jitter and if program switch intermitently two programes are overjumped. (picture attached)
• Picture is stretched towards the top and foldover. (+ extract of circuit diagram)
• Menu for volume appears automatically and can not be adjusted.
• Bright, horizontal stripe in picture centre. No vertical deflection.
• Adjusting the SECAM (4.25MHz) colour carrier trap: Chassis.
• Slightly visible vertical stripes in picture.
• Intermittently picture runs through, vertical sync jitters and two programs are intermittently skipped when changing programs
• Display too big and shifted to the right. (+ extract of circuit diagram)
• Distorted and low sound shortly after start-up, then ok.
• Linearity fault. Too high image amplitude. East /west equalitsation not adjustable. (picture attached)
• Intermittently picture runs through. Vertical synchronisation jitters. Intermittently jumps over two channels by program switch-over.
• Adjusting the R-Y demodualtor: chassis.
• Horizontal output stage transistor is defective.
• No E/W equalisation. E/W phase and amplitude control no response. (+ extract of circuit diagram)
• Imtermitent image rinning through, vertical sync jitters and if program switch intermitenlty two programs are overjumped. (part of circuit diagram displayed)
• No E/W distortion. E/W phase and amplitude control do not react
• Bars in picture. (picture attached)
• After turning on TL19 (S20AF) is immediately destroyed. (with circuit diagram extract)
• Picture too bright and green.
• Line tearing for a few minutes after start-up, then horizontal stripes on picture.
• Poorly visible vertical lines in image. (picture attached)
• Linearity fault. Picture amplitude too large and E/W distortion cannot be adjusted
• Too big and display shifted to the right. (with circuit diagram extract)
• Main voltage (U SYST.) (6408IMC tips)
• Too big display and display shifted to the right. (picture attached)
• Setting the bell filter: chassis.
• No tele-dialog display with front control or remote control. (+ extract of circuit diagram)
• Intermittently picture runs through. Vertical synchronisation jitters. Intermittently two programs are jumped over during program switch-over.
• Reliability of TL19. (NORDMENDE - 6408IMC information)
• No switch on in protective circuit mode. Standby power supply and LED ok. (picture attached)
• Switches off after 5 sec, no picture.
• Poorly visible lines in image. (+ extract of circuit diagram)
• Adjusting the NTSC (3.58MHz) colour carrier trap: Chassis.
• No E/W equalisation. E/W phase and amplitude controls do not respond. (+ extract of circuit diagram) (NORDMENDE - 6408IMC information)
• Starts up, HV is present for a few secs, then appliance switches off and PSU switches to protective circuit
• Sound rustles in STEREO. (6408IMC tips)
• Sound fault. Fault disappears nearly when switching to mono.
• RF noise. No picture.
• Noise on audio at low volume.
• Adjusting the peak white: chassis.
• No switch on. Appliance in safety mode. Standby dot lit. (picture attached)
• Picture width changes when adjusting contrast (beam current dependent). (with circuit diagram extract)
• No E/W distortion. E/W phase and amplitude controls do not respond. (with circuit diagram extract)
• No tuning. (service info for NORDMENDE -6408IMC)
• No north-south correction. (part of circuit diagram displayed)
• Setting the audio trap.
• RF noise and no picture
• Picture is too bright and too green.
• No switch on. Appliance in safety mode. Standby dot lit. Standby power supply ok. (+ extract of circuit diagram)
• White adjustment: picture tube board.
• Linearity error. Too high picture amplitude. No E/W correction.
• Picture too big. Picture shifted to the right.