308356 / OTTOVERSAND [TV]

• Interference on low channels. (extract of circuit diagram attached)
• No colour (after a few minutes). (part of circuit diagram displayed)
• Red picture. Flyback lines. Trips.
• Stuck in standby. (+ extract of circuit diagram)
• Resembles incorrect tuning, or the appliance goes to mute. (with circuit diagram extract)
• Appliance blows circuit protectors PS601 and PS602.
• Starts up, red LED flashes twice then goes dead. (with circuit diagram extract)
• Horizontal line. (with circuit diagram extract)
• Picture and sound is intermittent or negative picture.
• Vertical collapse. (extract of circuit diagram attached)
• Ragged verticals at bottom 2 inches. (extract of circuit diagram attached)
• Service information. Mcb connecting leads. (part of circuit diagram displayed) (OTTOVERSAND - 308356 information)
• Bright screen and retrace lines about 2 inches from top. (picture attached)
• Picture is vertically too small and has rounded corners. (with circuit diagram extract)
• Starts up 4 times, then no function. (picture attached)
• OSD and picture noisy. (picture attached)
• Dead. Standby LED lights, protective circuit starts up.
• When increasing volume of appliance via RC, sound becomes lower by itself after finishing the adjustment, also when lowering volume appliance becomes louder or lower ie. sound varies. (+ extract of circuit diagram)
• Program display appears suddenly. Then RC doesn't function any more. (part of circuit diagram displayed)
• Power supply voltage is too high. Cannot be adjusted with pot. (picture attached)
• Screen remains black or picture is poor.
• Collapsed verticals.
• +B too low, can only be adjusted from 90V to 120V (with circuit diagram extract)
• Hum at switch on. Purity spots.
• White horizontal lines across top of picture.
• Squealing noise at switch on with mains switch. Appliance goes in standby. Power LED flashes. (+ extract of circuit diagram) (OTTOVERSAND - 308356 information)
• PSU transistor and fuse 4A are destroyed after 1-3 mins. (part of circuit diagram displayed) (308356 tip from OTTOVERSAND)
• Blank raster. (with circuit diagram extract)
• Picture and sound are intermittent; channel number still present. (extract of circuit diagram attached)
• Picture and sound disappear intermittently. On-screen display is disturbed. (part of circuit diagram displayed)
• Loud noise intermittently and no picture after start-up. Error appears rarely. (+ extract of circuit diagram)
• No start-up. after warm-up. (OTTOVERSAND - 308356 information)
• After a while skips to another program station at random. (extract of circuit diagram attached)
• Rustle of EHT at switch on then powers down with LED flashing four times. (+ extract of circuit diagram) (OTTOVERSAND - 308356 information)
• Tuner IF fails. Picture is red then black. (part of circuit diagram displayed) (308356 tip from OTTOVERSAND)
• Q602 (2SD1548) blown at start up. (part of circuit diagram displayed)
• Programm jumps from 2 to 32 or from 4 to 36 or from 6 to 38 after some time.
• Vertical foldover at top. (extract of circuit diagram attached) (service info for OTTOVERSAND -308356)
• After working ok for a while, interference on picture and sound. Channel display always shows "00". (extract of circuit diagram attached)
• No switch on from standby. The TV will not come on from standby but the standby LED is lit. 21" and 25" sets only. (with circuit diagram extract)
• Attempts to start up but remains unstable. Clicking noise from chopper. LED switches on at the same rythm.
• Chopper transistor S/C. (with circuit diagram extract)
• Shaking picture. Tearing picture. Distorted picture. (+ extract of circuit diagram)
• +B voltage can not be adjusted. (part of circuit diagram displayed) (308356 tip from OTTOVERSAND)
• No start-up. intermittently. (part of circuit diagram displayed)
• Standby LED flashes slowly. (picture attached)
• Vertical output stage bcomes defective after few weeks. (picture attached)
• Only starts up after several attempts or PSU switches off again.
• How to adjust beat zero.
• Dynamic convergence is out of adjustment.
• Pale or distorted picture or black and white picture. (extract of circuit diagram attached)
• Blocked on one programme place and when switching it always goes back. (extract of circuit diagram attached)
• When connecting TV in cold conditions, picture flickers. Knock sensitive fault. (extract of circuit diagram attached) (308356 tips)
• Mechanical screeching, whistling, chirping from HV unit. (part of circuit diagram displayed)
• No picture. Standby LED does not light.
• OSG sways from side to side. (picture attached)
• Error codes. (picture attached)
• Switching transistor and mains fuse fail repeatedly. (part of circuit diagram displayed)
• Switches off by itself. at start-up.
• Faulty OSD. (extract of circuit diagram attached)
• No start-up from standby with RC. (308356 OTTOVERSAND repair tip)
• Black screen and no sound when switching TV on in cold conditions. Standby LED lights up after a short while. TV functions OK. Loud "plof" noise in loudspeakers. (part of circuit diagram displayed)
• Occasionally appliance cannot be switched on from the mains switch. (part of circuit diagram displayed)
• Attempts to start up once, gives three pulses and then goes into safety mode.
• Picture too big. Switches off by itself. (extract of circuit diagram attached)
• No RC functions or OSD. Intermittent colour, then intermittent video. (part of circuit diagram displayed)
• Green purity smear at upper left coin and purple purity smear at upper right corner.
• Pincushion distortion. (+ extract of circuit diagram) (service info for OTTOVERSAND -308356)
• Slow start-up. (+ extract of circuit diagram)
• Switches to protection mode. after start-up.
• Picture height too low and rolled-up from the top.
• Black screen. No RC functions. (picture attached)
• Flyback lines. at top. (+ extract of circuit diagram)
• Picture rolls/goes B/W or line twitching at top of screen.
• Picture foldover at the bottom of the screen. Adjustments work but fault persists, (with circuit diagram extract)
• Frizzy picture width which is not constant. (part of circuit diagram displayed)
• B1 board change. (308356 tips)
• Slow start-up. when cold. (extract of circuit diagram attached) (308356 OTTOVERSAND repair tip)
• Horizontal, black lines in picture depending on for how long the appliance is ON. Usually after a while RC will also no longer function. Sometimes the opposite effect, RC does not work then after a period of time black lines appear. (+ extract of circuit diagram)
• FET chopper transistor BUZ91A fails. (+ extract of circuit diagram)
• Picture is too wide, distorted, goes into safety mode if not adjusted. (with circuit diagram extract)
• Reduced vertical size. Poor vertical linearity. (extract of circuit diagram attached)
• No picture. Audio OK . (part of circuit diagram displayed)
• Power supply starts up and goes then to PROTECT mode. Standby light on. (+ extract of circuit diagram)
• Picture is too wide and fails when warm. (extract of circuit diagram attached)
• Picture disappears intermittently with strong noise from FBT. Screen remains black and impossible to switch over channels. OSD remains stuck.
• At switch on picture takes longer than usual to appear (tube unblocking). (part of circuit diagram displayed)
• PSU transistor fails again after approx 3 mins. (part of circuit diagram displayed)
• No picture. No audio. after a while. (+ extract of circuit diagram) (service info for OTTOVERSAND -308356)
• No picture, no RC reception, LED flashes a few secs.
• Green picture. Black screen. intermittently. Audio and OSD OK .
• Channel drift.
• Vertical foldover at bottom. Reduced vertical size. (+ extract of circuit diagram) (308356 tips)
• PSU ticking. LED flashes 5 times. (part of circuit diagram displayed)
• No or intermittent start-up. Knock sensitive. (part of circuit diagram displayed)
• Flashing picture intermittently. May also have colour dropout. See also bulletin TV00593.
• Intermittent colour and picture flashing. (service info for OTTOVERSAND -308356)
• Vertical deflection fails or only vertical lines are visible. (with circuit diagram extract)
• No vertical deflection. (with circuit diagram extract) (308356 OTTOVERSAND repair tip)
• Dark picture is lower third, upper third folded down. (extract of circuit diagram attached)
• After a flash goes back to channel 0. OSD displays VIDEO 00. (+ extract of circuit diagram)
• Signal loss on all channels with red or blue characters. Bright points on screen as if aerial disconnected. Picture is OK sometimes but with no colour.
• Flashing picture. Applicable to sets which have a new B1 board without a screening can. See also bulletin TV00692. (+ extract of circuit diagram)
• Switches to standby. (part of circuit diagram displayed)
• Teletext ok. Otherwise only a dark picture with digit OSD without sound. (extract of circuit diagram attached)
• Sound crackles with OSD flashing. (+ extract of circuit diagram)
• Crackling audio. when cold. Knock sensitive. (+ extract of circuit diagram)
• Horizontal lines from top to bottom on screen. (extract of circuit diagram attached)
• Crackling noise. Flash-over at switch on.
• Red flyback lines. (extract of circuit diagram attached)
• Purple stain on top right-hand side corner.
• OSD moves and flashes. Volume level changes spontaneously. (with circuit diagram extract)
• Flickering picture. (extract of circuit diagram attached)
• Erratic start-up. Standby LED flashes . (extract of circuit diagram attached)
• Dark screen. Audio OK . (+ extract of circuit diagram)
• Starts up on channel 59. It is possible to set standard and channels but appliance switches back to channel 59 as soon as memory key is pressed. LEDs A and STEREO are lit. (OTTOVERSAND - 308356 information)
• Varicap voltage drift.
• Service information. Original tuner (SUF944PLL) is replaced by tuner U944C. Only for UK models. (picture attached)
• No reception (intermittently). (extract of circuit diagram attached)
• 12V missing on IC608. (extract of circuit diagram attached)
• Retrace lines. after warm-up. (part of circuit diagram displayed)
• No colour (intermittently). (with circuit diagram extract)
• No picture after 5 mins. It bounces twice, then screen becomes dark. Program display is 00. If program is selected again, picture reappears. (picture attached)
• Switches automatically to another channel after approx. 5 min. Preferentially to channel-S2 (112.25 MHz). Intermittently tuner switches to another frequency also. (part of circuit diagram displayed)
• No or intermittent start-up. (with circuit diagram extract)
• Picture is poor with flyback lines and pulsing brightness. (part of circuit diagram displayed) (308356 OTTOVERSAND repair tip)
• No audio. Picture OK . (308356 tip from OTTOVERSAND)
• OK at switch on, then after few secs, sound becomes loud, picture flickers, field cramping, picture loss then reappears expanding away with loss of field scanning, then goes dead. (picture attached)
• Poor colour reproduction. Brightness adjustment doesn't function. (+ extract of circuit diagram)
• Picture is red. If colour contrast is reduced, picture is black-white.
• Horizontal white line. (+ extract of circuit diagram)
• Picture runs through. (+ extract of circuit diagram)
• No picture. Sound only via AV. Brightness, colour, control OK. (+ extract of circuit diagram)
• Picture appears and disappears with horizontal sync tearing. (picture attached) (service info for OTTOVERSAND -308356)
• Switches on. Signs on the screen, green bar and sound dropout. (extract of circuit diagram attached)
• Switches immediately to program 0 at switch on. Impossible to change. (extract of circuit diagram attached)
• Hiccups 4 times and then fails (in cold condition). (part of circuit diagram displayed)
• Picture only appears approx 2 mins after switch on. Audio OK. (picture attached)
• Switches on twice for a short time switches off.
• Volume varies. (+ extract of circuit diagram)
• Distorted audio. The speaker cabinet vibrates.
• Lines in picture. (extract of circuit diagram attached)
• Horizontal bars when switching channels. Switches off intermittently. Fault may not appear for a long time. (with circuit diagram extract)
• No picture. Text has one colour missing. (picture attached) (308356 tips)
• No degaussing.
• CATV interference. (part of circuit diagram displayed)
• No start-up. when cold. LED blinks . (with circuit diagram extract)
• Picture appears slowly. when cold. No audio. intermittently. (extract of circuit diagram attached)
• Starts 4 times and then turns OFF. (picture attached)
• Diminishing power supply. (with circuit diagram extract)
• No RC functions. intermittently.
• Picture collapses. Sound is cracking. LEDs light up and go out. OSD flickers. (part of circuit diagram displayed)
• PSU pulsates. (+ extract of circuit diagram)
• Reduced vertical and horizontal size. Low audio. (part of circuit diagram displayed)
• OSD shifts after approx 10 mins then no picture and no sound. (with circuit diagram extract)
• OSD flickers. Intermittently buzzing sound. (extract of circuit diagram attached)
• No colour. via SCART. (picture attached)
• Dim picture. Excessive brightness. (+ extract of circuit diagram)
• Switches to standby (intermittently). (with circuit diagram extract)
• Cramped at centre, stretched at top and fold over at bottom. (picture attached)
• Starts up at switch on, red LED flickers then appliance goes dead. (with circuit diagram extract) (308356 tip from OTTOVERSAND)
• No RC functions. Hum in audio. (part of circuit diagram displayed) (OTTOVERSAND - 308356 information)
• Degaussing does not work on the sides of the picture.
• PSU pumps three times at switch on. Standby LED switches off.
• Occasionally picture and sound disappear (go out of tune), mainly a short time after switch on, if appliance is cold.
• 137V voltage collapses at switch on. (picture attached)
• No tuning.
• Yellow, approx 5mm vertical line through the picture. (with circuit diagram extract)
• No picture. No sound. No keyboard and RC functions. LED blinks every 5 seconds.
• Text picture geometry distorted.
• Trips 3 times then enters safety mode. (+ extract of circuit diagram)
• Grey screen. Retrace lines. after a few seconds. (+ extract of circuit diagram)
• Black screen. intermittently. (part of circuit diagram displayed)
• Poor vertical linearity (stretched at the top, collapsed at the bottom). (picture attached)
• Frame output chip blown repeatedly. (part of circuit diagram displayed) (service info for OTTOVERSAND -308356)
• Channel OSG sway intermittently from side to side then set powers down. (part of circuit diagram displayed) (OTTOVERSAND - 308356 information)
• Pumps, starts after several attempts. Picture and sound OK.
• On screen display is constantly mixed up. Flickering picture and plopping sounds. (picture attached)
• Flickering picture. No picture. intermittently. (part of circuit diagram displayed)
• Spot on right of picture.
• After start-up protective circuit switches on, after several start ups appliance functions. (part of circuit diagram displayed)
• Dead. (picture attached)
• Picture flickers and breaks down (wobbles).
• Colour disappears after switching to a different channel. (picture attached)
• Appliance must be switched on for 10 minutes before picture appears. (extract of circuit diagram attached) (308356 tips)
• Dead. No standby. Switches 3x quietly. (+ extract of circuit diagram)
• Width is reduced and verticals bent. (part of circuit diagram displayed)
• Dark picture with red stripes. Picture is OK after approx 5 mins, but red is missing.
• Picture fails. (part of circuit diagram displayed)
• Intermittent loss of colour or colours getting brighter and more saturated as set warms up. (+ extract of circuit diagram)
• Pulsating picture.
• It may happen that during a Mono broadcasting, the stereo LED switches on. At this time, a strong audio noise may be heard.
• Vertical lines are bent inwards in the corners of the picture. (+ extract of circuit diagram)
• No picture (intermittently).
• White horizontal lines in picture. Broad lines when cold. Thin lines when warm, or no lines. (with circuit diagram extract)
• OSG jitters, audio crackles and loss of colour.
• Vertical amplitude too low . Bad vertical linearity. Dark picture at bottom. (picture attached)
• Retrace lines. (extract of circuit diagram attached)
• No channel storing. (extract of circuit diagram attached)
• Flashing horizontal black lines. Occasionally appliance may function OK. (with circuit diagram extract)
• Stuck in standby. Comes on when powered ON/OFF a few times but with no picture for approx. one min; followed with flyback lines as set warms up. (extract of circuit diagram attached)
• Vertical line. (with circuit diagram extract)
• Q602 defective. (+ extract of circuit diagram)
• No switch on from standby. Power supply shuts down. (with circuit diagram extract)
• Channels drift and go back to 00. (+ extract of circuit diagram)
• Starts up with a plopping noise from loudspeakers. Bright horizontal stripes in tuner picture in the first minutes of operation. Intermittently picture and sound OK after half an hour. (picture attached)
• Varicap adjustment (tuning) shifts intermittently. (308356 OTTOVERSAND repair tip)
• Picture disappears after short operation. OSD oscillates. (part of circuit diagram displayed)
• Reduced picture size. Horizontal line. (part of circuit diagram displayed)
• Channel memory loss at switch off. No volume control. Remains on original adjustment. Program OK. Channel tuning OK. (part of circuit diagram displayed)
• The screen is black or very dark. (picture attached)
• Pincushion distortion. on sides. Excessive horizontal size. (picture attached) (308356 tips)
• No start-up. (part of circuit diagram displayed)
• Sound goes to maximum when adjusted. (picture attached) (OTTOVERSAND - 308356 information)
• Picture and sound drop intermittently out. Only green programme display in picture. (picture attached)
• Intermittently top of screen rolls, loses colour, picture pulses or twitches.
• Loss of picture. Picture shows flashes.
• Switches after switch on immediately to channel site 33. If set is switched on with button 1 on RC, it switches to channel 33.
• Horizontally distorted picture. Rattle. (picture attached)
• Picture sometimes becomes slanted with underlining. (+ extract of circuit diagram)
• No start-up. LED blinks . (with circuit diagram extract) (308356 tips)
• No start-up from standby. (picture attached)
• Strong noises from demagnetizing coil after plug has been pulled out. (part of circuit diagram displayed)
• No picture. No audio. intermittently. OSD OK .
• Lines approx 5cm at the top. (picture attached)
• Intermittent picture size. (+ extract of circuit diagram)
• No picture. when changing channels (intermittently). (with circuit diagram extract) (service info for OTTOVERSAND -308356)
• Intermittent symptoms - picture rolls, goes black and white with pulsing, or line twitching occurs at the top of the picture.
• Excessive brightness with retrace lines even when brightness is on minimum. (part of circuit diagram displayed)
• Tries to start up. Standby LED flashes three or four times then goes out. After insisting a few times, it eventually starts up. (extract of circuit diagram attached)
• Only a green streak in the middle of screen. OSD appears on this streak.
• HT too high at 175V. (picture attached)
• Warped picture after some time. (extract of circuit diagram attached)
• Intermittently stops. (extract of circuit diagram attached)
• White or RGB stripes on the upper part of picture. (+ extract of circuit diagram)
• Occasionally varicap tuning shifts. Black picture, no sound, hum. (OTTOVERSAND - 308356 information)
• Intermittently microprocessor locks up with parental lock displayed. No signals. (picture attached)
• Ticks 3 times, then no function. (extract of circuit diagram attached)
• Sound only briefly present, then only mute.
• Picture width twitching. Poor E/W. (with circuit diagram extract)
• Veil and picture oscillation. (picture attached)
• No synchronisation. (with circuit diagram extract)
• Loudspeaker crackle at switch on, no picture content.
• Q602 (2SD1548) blows at start up and fuse blows. (picture attached)
• Volume uncontrollable. (+ extract of circuit diagram) (service info for OTTOVERSAND -308356)
• Picture green, with green lines. (picture attached)
• Flyback lines. Dark picture. after a while. (part of circuit diagram displayed)
• No power up. Standby LED flashing with 12 secs intervals. (part of circuit diagram displayed)
• Intermittent colour (after warm-up).
• Switches to standby (after start-up). (+ extract of circuit diagram) (OTTOVERSAND - 308356 information)
• Severe hum in standby on left channel. OK in standard mode. (part of circuit diagram displayed)
• No picture. (with circuit diagram extract)
• No HV. (+ extract of circuit diagram)
• Excessive horizontal size. E/W fault. (extract of circuit diagram attached) (308356 OTTOVERSAND repair tip)
• Vertical jitter. LED blinks . Trips. (extract of circuit diagram attached)
• Insufficient height and cramping at centre of screen. (part of circuit diagram displayed) (OTTOVERSAND - 308356 information)
• Black and white picture with strobe effect. (part of circuit diagram displayed)
• OSG are black and should be green.
• Pulsates 4 times on start up from mains and then switches off. No standby display. (+ extract of circuit diagram)
• The white balance varies when changing the colour intensity. (with circuit diagram extract)
• Intermittently switch to PR00. (extract of circuit diagram attached)
• Vague horizontal bars and picture takes a long time to appear. Noise in the start up speaker. (+ extract of circuit diagram)
• No start-up. when cold. (extract of circuit diagram attached)
• No functions. (extract of circuit diagram attached)
• Rhythmical ticking after start-up. (extract of circuit diagram attached)
• No power supply. Rattle for a few seconds. (+ extract of circuit diagram)
• Intermittently picture collapses and blanks out.
• No picture at switch on. No OSD display. Sound present. Picture appears after 1 to 2 min. Time difference for when picture appears do not decrease significantly after switching off and on again. (picture attached)
• Black screen. Audio OK . (extract of circuit diagram attached) (service info for OTTOVERSAND -308356)
• It is constantly on program site 2. Analog values can be adjusted but bounce back immediately to the initial value (part of circuit diagram displayed)
• Pulsates four times at switch on and then switches to standby.
• Bright bar at top of screen. (picture attached)
• No switch on and red light on. 140V present. No input signal on line transistor base. (picture attached)
• No driver transistor Q805 command. (with circuit diagram extract)
• Picture compressed in the centre. Black band at the bottom of the screen. (part of circuit diagram displayed)
• Screen doesn't light up. HF noise from loudspeakers. (with circuit diagram extract)
• Picture size incorrect. Change in size of raster. (extract of circuit diagram attached)
• Low contrast comes up after while. Flyback lines. (part of circuit diagram displayed)
• Purity errors and E/W distortion.
• No audio. OK via SCART . No picture.
• Distorted picture and vertical sync when switching on
• No functions. Starts up, then beeps 3 times and shutsdown. (picture attached)
• PSU IC and PSU transistor defective. (+ extract of circuit diagram)
• No function with the RCU. IR receiver functions. IR data reach the microprocessor. RCU functions with another CTV. (+ extract of circuit diagram)
• After a while starts switching between the channel where it was at that moment and channel 00. After restart remains on channel 00. (+ extract of circuit diagram)
• Fine stripes in upper quarter of picture. (part of circuit diagram displayed)
• Poor picture with red line. (service info for OTTOVERSAND -308356)
• Jumps from program site 2 to 00, jumps to and fro, then stays on program 00. (picture attached)
• No RC functions. (part of circuit diagram displayed)
• Switch has to be pressed several times to start the appliance. Sound fault. (extract of circuit diagram attached)
• Intermittent HV flashover at the CRT neck.
• Switches to video input if a VCR is connected via scart and VCR is switched to standby. (picture attached)
• Noise in picture. at high volume.
• Line output stage defective. (part of circuit diagram displayed) (308356 OTTOVERSAND repair tip)
• Attempts to start up three times, then switches to protection mode.
• Poor colour. One colour missing. Low brightness. (with circuit diagram extract)
• If a program is selected,appliance switches to and fro between selected program and 00, sometimes several times per sec. Picture temporarily OK. (extract of circuit diagram attached)
• Vertical line. in the centre. (part of circuit diagram displayed)
• No audio. (picture attached)
• No raster. (part of circuit diagram displayed)
• A space between the tube and the cabinet may be visible.
• Tripping. (with circuit diagram extract)
• No OSD. No reception. Black screen. Standby LED flickers every 20 seconds. (with circuit diagram extract)
• No audio (after a few minutes). (+ extract of circuit diagram)
• Dark picture with on-screen display, no sound. Videotext is OK. (+ extract of circuit diagram)
• Tuner adjustment is off tune. Fine tuning does not store information.
• OSD flickers constantly. Intermittently goes into standby. (with circuit diagram extract)
• No operation (intermittently). (picture attached) (308356 OTTOVERSAND repair tip)
• Distorted picture. Interference in picture. (extract of circuit diagram attached)
• OSD flickers, picture disappears after a while. (+ extract of circuit diagram)
• OSD fades away. (+ extract of circuit diagram)
• Picture has green line going down. (with circuit diagram extract)
• No raster. Audio OK . (with circuit diagram extract)
• IC8170 blows at switch on. (+ extract of circuit diagram)
• Picture distorted and reduced. Picture becomes longer when hot. (+ extract of circuit diagram)
• Poor linearity. at top. (extract of circuit diagram attached) (308356 tip from OTTOVERSAND)
• Procedure to initialise Eprom after replacement.
• Black horizontal lines in the middle of the picture (possibly at the bottom as well). (picture attached)
• Poor picture. Flyback lines. (part of circuit diagram displayed)
• Channel number flickers between two numbers. (extract of circuit diagram attached)
• Intermittently PSU does not start up. (picture attached)
• Power supply chopper transistor 2SD1548 S/C. (part of circuit diagram displayed) (service info for OTTOVERSAND -308356)
• Power supply goes on and switches then on and off rhythmically. Several white streaks on screen for a short while. (picture attached)
• Program number OSD is permanently displayed. (picture attached) (308356 tip from OTTOVERSAND)
• Strong colours. (+ extract of circuit diagram)
• Standby LED blinks intermittently after switch on. (part of circuit diagram displayed)
• Vertical lines are ragged. (+ extract of circuit diagram)
• Vertical streaks. at top. (picture attached)
• OSD bounces intermittently from left to right. If it bounces too intense, brief loud sound interference appears and program switches over or switch on problems occur. (picture attached)
• Dead (intermittently). (+ extract of circuit diagram)
• Flickering colours. Knock sensitive.
• Pulsating picture. Distorted picture.
• Drops out intermittently and switches to another channel and sound crackles. (with circuit diagram extract)
• Switches to next odd number when selecting preset even number (2,4,6, etc.) (without using RC). (extract of circuit diagram attached)
• Only channels 59 and AV present; audio is set to maximum. (extract of circuit diagram attached)
• Cramping at bottom of screen, width reduction and loss of audio. (picture attached)
• Stations drift off tune or search does not stop. (picture attached)
• HV crackles shortly after switch on, then no function. (with circuit diagram extract)
• No TXT. (extract of circuit diagram attached) (308356 tip from OTTOVERSAND)
• Poor linearity or geometry. Frame linearity fault. Usually only occurs in sets which are more than two years old. (+ extract of circuit diagram)
• Switches to program site 00 after operating for a while.
• PSU fails. (part of circuit diagram displayed) (308356 tips)
• Cycles on/off. (with circuit diagram extract)
• Brief start up of power supply. Standby LED then flashes 4 times. (+ extract of circuit diagram) (308356 OTTOVERSAND repair tip)
• Shuts down. (extract of circuit diagram attached)
• Picture on left side is concaved. (+ extract of circuit diagram)
• Pulsates four times then switches off. (OTTOVERSAND - 308356 information)
• Black screen. No display. (+ extract of circuit diagram)
• Pulsates 4 times, then no function.
• No picture. No OSD. (part of circuit diagram displayed)
• Starts up three times then switches off. (part of circuit diagram displayed)
• No start-up. after lightning strike. (picture attached)
• No subtitles with the "Subtitles for the hard of hearing" decoder. (extract of circuit diagram attached)
• At switch on pulsates 3 times. (+ extract of circuit diagram)
• PSU switches 4 times, then no function.
• Sound level decreases. OSD shows decrease.
• OSD flickers. Speakers whistle. (with circuit diagram extract)
• Sporadic interference from loudspeaker.
• Power problem intermittently. At switch on the red power supply lamp may light up but the power supply may sometimes trip as in overcurrent detection. (part of circuit diagram displayed)
• TXT doesn't function. Greenish background.
• Picture appears slowly. (+ extract of circuit diagram)
• Wrong colours which are displaced half inch to the right. (with circuit diagram extract)
• Stuck in Canal Plus. (with circuit diagram extract)
• Distorted frame. (with circuit diagram extract)
• Low audio (on the right). (picture attached)
• Pincushion distortion. at bottom.
• Switches to protection mode. (part of circuit diagram displayed)
• OSD channel insertion remains permanently in the picture. Can be switched off with the RC. (with circuit diagram extract)
• Deflection fault, distortion and picture oscillation at bottom of screen. (extract of circuit diagram attached)
• Blurry picture. (part of circuit diagram displayed) (service info for OTTOVERSAND -308356)
• Channels change at random.
• Slight top foldover plus 6 faint flyback lines (2 red, 2 green, 2 blue). (+ extract of circuit diagram)
• Doesn't start up with mains switch when cold. Standby LED flashes 4 times. (part of circuit diagram displayed)
• Black hum bar type effect for first few secs after channel change. (picture attached)
• Shuts down (intermittently). (part of circuit diagram displayed)
• No vertical synchronisation on bright picture content via scart.
• Contrast too low in certain mode. A dark picture is displayed in the rgb mode. (part of circuit diagram displayed)
• Power supply hiccups. (part of circuit diagram displayed)
• Does not switch to standby correctly, it can be started again only by control on appliance. (extract of circuit diagram attached)
• Cannot go to standby even after a few attempts to switch ON. (part of circuit diagram displayed) (308356 OTTOVERSAND repair tip)
• Horizontal lines. (+ extract of circuit diagram)
• Horizontal lines across screen. Humming. (part of circuit diagram displayed)
• No picture or sound after a while. OSD shows video output. (extract of circuit diagram attached)