558064 / OTTOVERSAND [TV]

• Geometry has shifted or appliance does not switch on.
• Voltages are too low.
• Bright, white picture with flyback lines, switches off after 10 sec.
• No RC functions.
• No or intermittent start-up. Switches off by itself. after a while. (picture attached)
• No sound on some programs or sound appears later.
• No Dynamic Noise Reduction setting with software version AE306.
• Poor audio. on the left.
• Intermittently dead.
• PSU starts and switches off immediately. No LED display. (558064 OTTOVERSAND repair tip)
• Picture too dark and/or various irregularities in geometry, brightness and volume. Also incorrect PB from the menu or spontaneous menu action. (with circuit diagram extract)
• No audio. No picture.
• No HV. after a few seconds.
• E/W fault. intermittently. Vertical fault. intermittently. Switches off by itself.
• Red picture. Picture too small.
• Low contrast. after a while. Flyback lines.
• Comes on for a short time.
• Dead.
• Intermittentlly no function at switch on. No display (LEDs dark). If mains plug is removed and plugged in again, PSU starts up intermittently.
• Slight hum from speakers. (OTTOVERSAND - 558064 information)
• Poor picture. OSD and TXT OK . (picture attached)
• TXT menu corrupted. A number of characters is repeated. (with circuit diagram extract)
• Audio plop when switching preset channels. (picture attached)
• No picture. after start-up. Audio OK .
• RC unit.
• No function. Squeaking sound from power supply.
• Switches to protection mode. (picture attached)
• Shuts down. after start-up.
• Poor picture. Low audio.
• Picture is black. Menu, OSD, text and sound OK. Channel B LED blinks 5 times.
• No picture. intermittently.
• After setting volume to max, sound drops out, then cannot switch TV back on or it starts up but, if put into standby, does not switch on and, in this case, no front LED. (558064 OTTOVERSAND repair tip)
• No picture, only AV OSD.
• Very dark picture. No sound. Geometry faults.
• RC unit.
• Test lines in upper picture half can be seen, vertical deflection distorted at upper picture edge.
• Switches to standby after a few secs. LED A blinks once, then LED B blinks 4 times and cycle repeats itself.
• Black lines at the bottom of the picture, increase with time. (558064 tips)
• No colour. (OTTOVERSAND - 558064 information)
• Vertical streaks.
• RC unit.
• Raster ringing and H-linearity. (picture attached)
• Picture switches randomly from large to small format at irregular time intervals. (558064 tips)
• A & B LEDs flashing in standby causing appliance to switch on intermittently from standby.
• Appliance starts up, but no LED, no vertical deflection audible and switches off after approx. 10 secs.
• Noisy picture, picture and picture is OK in VHF.
• No function after being switched off and immediately switched on again. Applies to switch off/on with mains switch and from standby.
• LED A blinks once, then LED B blinks 4 times. Cycles.
• Picture disappears when vertical deflection fails, appliance cannot be switched on then. Protective switching responds at every start up.
• Green picture. Flyback lines.
• Red, green or blue picture with flyback lines. (part of circuit diagram displayed)
• Dark picture for half an hour, then picture with poor contrast.
• OSD appears in picture for 2 secs as soon as picture appears after switch on then switches to protection mode.
• No colour in main picture. PIP OK.
• Starts up, HV builds up which can be heard then switches off after approx 3 secs. No LED display. (extract of circuit diagram attached)
• No picture ,OSD and Text available. LED blinks 4 times.
• No audio. Poor geometry.
• Audio fades. after a few seconds. Picture OK . (558064 tips)
• "PROTECT SP" displayed.
• Stripes and other interference in picture when switching to channels in band III. OK after 6 secs. (+ extract of circuit diagram)
• Flyback lines. (558064 OTTOVERSAND repair tip)
• How to enter service menu to adjust geometry.
• Horizontal line.
• Switches to protection mode. after a few seconds.
• No start-up.
• No RC functions.
• Colour and AFC fault when cold at switch over.
• No picture. (558064 tip from OTTOVERSAND)
• Red picture with flashes. Intermittent standby. Intermittent start-up.
• Error codes.
• No picture or picture is dark. No sound. Different geometry faults.
• Horizontal lines in zoom mode.
• Q601, Q602, Q615 fail repeatedly at switch on. (558064 OTTOVERSAND repair tip)
• Picture appears slowly. Audio OK .
• No OSD. Switches off by itself. after a while. (+ extract of circuit diagram)
• Low noise in sound.
• CRT socket. (service info for OTTOVERSAND -558064)
• Reduced vertical and horizontal size. Excessive red.
• Switches off by itself. after a few minutes. (service info for OTTOVERSAND -558064)
• Enter service mode.
• Blinking STEREO/NICAM LEDs in standby mode.