EURAS System
    EURAS worldwideeuras.com    
EURAS System

DV7036S / OTTOVERSAND [TV]

The EURAS repair tip database for professional technicians and service engineers supplies the following faults for DV7036S / OTTOVERSAND.

List of fault symptoms:
  • S-correction.
  • White screen. OSD OK .
  • Level adjustment audio R231.
  • Horizontale amplitude.
  • Sound level (R231) adjustment.
  • Picture shifted horizontally.
  • Switches to standby. after a while. (DV7036S OTTOVERSAND repair tip)
  • VCO for picture.
  • VCO T20 for picture adjustment. (service info for OTTOVERSAND -DV7036S)
  • Vertical size adjustment. (DV7036S OTTOVERSAND repair tip)
  • No colour.
  • Horizontal lines.
  • Multicoloured snow horizontally in the top third and vertically in the right third. Changes depending on picture content.
  • Shading in picture.
  • Service info: adjustment of the horizontal blanking phase.
  • East/West 1 adjustment. (DV7036S tips)
  • Trouble shooter T201,T200.
  • No synchronisation. Audio OK . (DV7036S tip from OTTOVERSAND)
  • Dead. Standby LED lit .
  • Horizontal phase shift adjustment. (DV7036S OTTOVERSAND repair tip)
  • Service info: E/W- and trapezoid corrections. (DV7036S tip from OTTOVERSAND)
  • No picture, high voltage is present, vertical deflection is present. Cut off voltage is only 1.3V.
  • S2 adjustment 5.74MHz.
  • No picture.
  • Service info: Audio level adjustment R231.
  • Replacement of VCU2136A with VCU2133.
  • G-2 adjustment
  • Colour is not in order. No drive from the digital board.
  • Service info: Adjustment of the vertical size.
  • +B 150V adjustment R716.
  • White screen and normal sound with aerial. Without aerial snow in the picture. (extract of circuit diagram attached)
  • No picture. No sound. Functions only after several restarts.
  • Cut-off blue adjustment.
  • Service info: Adjustment of the red section.
  • Flyback lines. (picture attached)
  • Colour is not in order. No drive from the digital board. (OTTOVERSAND - DV7036S information)
  • Bright picture. Flyback lines.
  • Service info: Adjustment of the green gain.
  • Vertical symmetry adjustment.
  • Horizontal blanking phase shift adjustment. (OTTOVERSAND - DV7036S information)
  • Trapezoid 2 adjustment.
  • Horizontal size adjustment.
  • Adjusting +B.
  • Vertical symmetry.
  • S detector 5.5MHz for sound.
  • Switches to standby. when cold. (extract of circuit diagram attached)
  • Horizontal amplitude adjustment (except 21" model).
  • Service info: adjustment of the red gain.
  • Trap T201 and T200 adjustment.
  • Trap T201 and T200 adjustment. (OTTOVERSAND - DV7036S information)
  • Power supply IC 701.
  • Vertical symmetry adjustment.
  • +B 150V adjustment. (service info for OTTOVERSAND -DV7036S)
  • AFT (T205) coarse adjustment.
  • Line end stage transistor.Q601 (2SD1546) fails.
  • Service info: Adjustment of the chrominance/luminance delay.
  • Service info: East/West 1 adjustment.
  • Picture is bright. TXT bright on bright background. Video signal only dimly distinguishable.
  • Chroma and luminance signal are mixed.
  • Service info: Adjusting the VCO.
  • Stripes in picture. at top. (part of circuit diagram displayed)
  • Service info: Adjustment of the VCO. (service info for OTTOVERSAND -DV7036S)
  • S detector T206 5.5MHz for sound adjustment.
  • Changing the horizontal blanking phase.
  • No yellow in the S-VHS function. (with circuit diagram extract)
  • Vertical size.
  • Coloured lines. at top.
  • No picture (after warm-up).
  • Service info: adjustment of noise suppressors T201, T200.
  • Voltage control oscillator T204 for picture adjustment.
  • Vertical size adjustment - Service mode.
  • No channel change or volume adjustment.
  • Trapezoid 2 adjustment - Except 21" model. (service info for OTTOVERSAND -DV7036S)
  • Service info: E/W- and trapezium corrections. (service info for OTTOVERSAND -DV7036S)
  • Stuck in standby. Power LED lit .
  • Phase shift. Does not go into chroma.
  • Clicking noise.
  • Horizontal amplitude.
  • Service info: Adjustment of the vertical size.
  • Dark blank raster.
  • Whitewash effect. No sync and TXT.
  • Power switch has to be switched 6-10 times when cold until appliance starts.
  • Hum in standby. (OTTOVERSAND - DV7036S information)
  • S detector T206 5.5 MHz for sound adjustment. (DV7036S tips)
  • Voltage control oscillator adjustment.
  • S2 T208 5.74MHz adjustment.
  • Service info: RF adjustment AGC R219.
  • Service info: Adjustment of audio level R231. (service info for OTTOVERSAND -DV7036S)
  • AFT Adjustment - Fine Adjustment.
  • Can be programmed, but only bright picture. Sound available for a short time by synchronisation. Picture available for a short time via scart. TXT OK.
  • Vertical symmetry adjustment - Service mode.
  • Horizontal blanking phase shift adjustment.
  • Cut-off red adjustment.
  • Service info: Adjustment of the VCO.
  • Horizontal blanking phase shift adjustment.
  • Poor picture. Distorted picture. (+ extract of circuit diagram)
  • VCO adjustment.
  • Sound can not be set to Low. If volume is increased sound disappears.
  • Grey picture without signal.
  • Trapezoid 2 adjustment. (service info for OTTOVERSAND -DV7036S)
  • Picture hardly visible, it appears with coloured dots on white screen.
  • Horizontal stripes. at top. (DV7036S OTTOVERSAND repair tip)
  • Green locking point.
  • No sound muting when switching over. No indication on the display eg. volume or Teletext. (part of circuit diagram displayed)
  • Sychronous fault, on the right blanking interval.
  • Service info: adjustment of the vertical phase. (DV7036S OTTOVERSAND repair tip)
  • Service info: Adjustment of trapezium 1.
  • Service info: East/West 1 adjustment.
  • Service info: adjustment of the vertical phase.
  • Fine tuning adjustment. (picture attached)
  • Does not start intermittently, squeaks (hiccups) when starting from standby mode. (extract of circuit diagram attached)
  • Service info: Adjustment of the red gain.
  • Service info: East/West 2 adjustment.
  • No sound. Buzzing.
  • East/West adjustment 2.
  • Cut-off red adjustment.
  • Only bright white picture. Sound, TXT and OSD OK.
  • Parts of text lines disappear when using subtitles.
  • No functions.
  • S-correction adjustment.
  • Vertical size adjustment.
  • Picture has horizontally shifted and has colour error.
  • Audio level adjustment R-331.
  • S-level adjustment.
  • Trouble shooting for T201, T200. (DV7036S tips)
  • Service info: Adjustment of audio level R231.
  • Colour is displaced.
  • Picture colour has shifted 1 cm.
  • PSU pulsates. Stuck in standby. (part of circuit diagram displayed)
  • Service info: RF AGC adjustment R219.
  • VCO adjustment.
  • No picture. via tuner. Audio OK .
  • No start-up from standby. (picture attached)
  • Horizontal blanking phase shift - Service mode. (DV7036S tip from OTTOVERSAND)
  • Service info: adjustment of the horizontal blanking phase.
  • Colour flickers and fades out.
  • Picture geometry changes continuously, no picture content visible, lines visible, no synchronisation, at switch on/off fault symptoms change continuously. (+ extract of circuit diagram)
  • Mostly black screen with intermittent vertical bars. Picture sometimes goes completely blue. Sound is ok intermittently.
  • AFT T205 adjustment.
  • VCO adjustment.
  • Service info: Trapezium 2 adjustment.
  • No audio.
  • No raster. (service info for OTTOVERSAND -DV7036S)
  • Service info: Adjustment of the vertical symmetry.
  • Poor and distorted picture, colour phase is not good. (with circuit diagram extract)
  • No sound, only digital sound is audible.
  • Drive blue.
  • VCO T204 for the picture.
  • Trap adjustment.
  • Occasionally a horizontal line visible for a short time. Then switches immediately to standby.
  • Service info: E/W 2 adjustment.
  • Detector T206 (5.5MHz) for the sound.
  • AFT coarse adjustment.
  • 150V cannot be adjusted.
  • Vertical collapse. (extract of circuit diagram attached)
  • Service info: Adjustment of the red section.
  • Line tearing. in the centre.
  • Service info: Ost/West 2 Adjustment.
  • East/west 1 adjustment (except 21" model).
  • Video signal fault. (DV7036S OTTOVERSAND repair tip)
  • Tripping (intermittently). (+ extract of circuit diagram)
  • AFT T205 adjustment.
  • Lines in picture. at top.
  • Service info: Adjustment of RF AGC R219.
  • No signal. via SCART. (extract of circuit diagram attached)
  • Trap adjustment.
  • Excessive horizontal size.
  • Audio adjustment T208 5.74MHz. (DV7036S tip from OTTOVERSAND)
  • Colour shifted.
  • Incorrect start-up. Screen flickers, cannot be controlled.
  • Line output transistor fails repeatedly.
  • Service info: Adjustment of VCO T204 for the picture.
  • Dark picture at start-up from standby. Picture appears if appliance is switched off via mains.
  • Dark picture. Poor picture. Retrace lines.
  • Hum in standby. (OTTOVERSAND - DV7036S information)
  • Green LED lights up briefly at start up, then LED goes off and PSU pulsates.
  • No E/W correction.
  • No sound. The end stage makes a noise. (picture attached)
  • Service info: Adjustment of detector T206 5.5MHz for the sound.
  • Test line in top third of picture.
  • Service info: Adjustment of the green gain.
  • Adjusting the detector for the sound.
  • S2 adjustment T208 5.74MHz.
  • No start-up.
  • Speakers click. Worse when warm. (DV7036S tips)
  • Does not start or starts with incorrect values for vertical and horizontal deflection. (DV7036S tip from OTTOVERSAND)
  • Service info: AFT adjustment T205.
  • No start-up. Standby and power LED simultaneously lit.
  • Red gain.
  • No vertical deflection.
  • Luminance and colour have shifted with respect to each other. (with circuit diagram extract)
  • Service info: East/West- and trapezium corrections.
  • East/West 2 adjustment.
  • G2 adjustment.
  • Drive red adjustment.
  • Service info: Adjustment of audio T208 5.74MHz.
  • Chroma luma distortion delay.
  • Service info: Adjustment of the horizontal blanking phase.
  • Service info: +B adjustment 150V R716.
  • +B 150V (R716) adjustment.
  • Squealing from PSU.
  • Blue gain.
  • Blue drive adjustment.
  • AFT fine adjustment.
  • No picture and no sound. If appliance is switched off and on again, it functions faultlessly.
  • Cut-off blue adjustment.
  • No OSD. No TXT. (service info for OTTOVERSAND -DV7036S)
  • AFT T205 adjustment.
  • Fault via the S-VHS socket. (with circuit diagram extract)
  • Replacement of the Digital-Board.
  • Only digital noise. Volume cannot be controlled.
  • Vertical size.
  • White splutters in the picture. (+ extract of circuit diagram)
  • S-correction adjustment - Service mode.
  • Disable the protective circuit.
  • No picture and sound. Power LED green, then red again.
  • How to activate SERVICE menu.
  • Reduced vertical size.
  • Tuning menú does not appear. No TXT. No OSD.
  • White picture or no raster.
  • Adjusting the VCO for the picture.
  • Hum in standby.
  • Tripping. (extract of circuit diagram attached)
  • Chroma-luma delay adjustment.
  • Switches to standby. after a few seconds.
  • E/W fault.
  • Vertical fails (line) when changing channels or with especially large jumps in brightness. (service info for OTTOVERSAND -DV7036S)
  • Enter service mode.
  • Detector T206 5.5 MHz for the sound.
  • Horizontal size adjustment.
  • Vertical symmetry.
  • Service info: Adjustment +B 150V R716. (service info for OTTOVERSAND -DV7036S)
  • Service info: Adjustment of AFT T205.
  • Adjusting the sound (5,74MHz).
  • Green gain.
  • Service info: adjustment of the S correction.
  • Service info: adjustment of noise suppressors T201, T200. (DV7036S tips)
  • Poor linearity. (DV7036S OTTOVERSAND repair tip)
  • Cut-off blue.
  • VCO T204 for the picture. f
  • VCO adjustment.
  • Red locking point. (service info for OTTOVERSAND -DV7036S)
  • Cut-off green adjustment.
  • G2 adjustment.
  • Line end stage does not run
  • Changing the horizontal blanking phase.
  • Coloured flyback lines at top.
  • Service info: Adjustment of the blue gain.
  • Service info: Audio adjustment T208 5.74MHz.
  • Service info: Adjustment of the red gain.
  • Service info: Adjustment of the vertical symmetry.
  • Sound is too loud with min. volume.
  • S detector T206 5.5MHz for sound.
  • S-level adjustment R231.
  • Horizontal phase shift adjustment.
  • S correction.
  • Vertical wavy lines at the top edge when cold (station logo is severely distorted). Picture (nearly) normal after a short time.
  • Trapezoid 1 adjustment.
  • Black and white picture is displaced towards the colour approx 5cm to the right.
  • Red poor when warm.
  • Green drive adjustment.
  • Drive red.
  • Venetian blind effect, picture is hardly recognisable. Sound OK. Error occurs either via aerial and via scart.
  • Line on left edge of picture.
  • Volume can not be turned down to 0. Cracks at switchover.
  • Intermittently spots in picture or picture too wide.
  • No picture. No synchronisation. (picture attached)
  • Weak contrast.
  • Service info: Adjustment of the chrominance/luminance delay.
  • Cut-off green.
  • Switches to protection mode.
  • East/West 1 adjustment
  • AFT adjustment - Coarse Adjustment.
  • Vertical phase adjustment.
  • No audio muting at switch over. No indication in the display eg. volume or Teletext. (picture attached)
  • Cut-off red adjustment.
  • In stand by low twittering/noise can be heard on the right channel. Occasionally appliance does not start up from stand by.
  • Dark picture.
  • Service info: Adjustment of the horizontal amplitude. (DV7036S tips)
  • Adjusting the horizontal amplitude
  • No channels. only snow.
  • Poor picture (green and bright). (picture attached) (DV7036S tips)
  • Colour is displaced. No memory. (service info for OTTOVERSAND -DV7036S)
  • Horizontal phase shift adjustment - Service mode.
  • Drive green adjustment. (OTTOVERSAND - DV7036S information)
  • Intermittently fails.
  • Service info: Adjustment of the S correction. (OTTOVERSAND - DV7036S information)
  • Service info: Adjustment of trapezium 1.
  • Chroma/luma delay adjustment.
  • Dim picture.
  • Drive red adjustment. (DV7036S tip from OTTOVERSAND)
  • Dead. (extract of circuit diagram attached)
  • No colour coverage.
  • HF AGC R219.
  • VCO adjustment - Service mode.
  • G2 adjustment.
  • No picture and no sound. The PSU does not start up. (with circuit diagram extract)
  • Horizontal phase shift adjustment.
  • Line tearing. at top.
  • Cut-off green adjustment.
  • No picture only bright even white screen. Teletext and sound ok.
  • Chroma luminance distortion delay.
  • TV switches to teletext when switched on and after awhile jumps back to regular picture. TXT is fine.
  • Service info: Trapezium 2 adjustment.
  • Sound level adjustment.
  • Setting fault-clearer. (with circuit diagram extract)
  • Horizontal size adjustment.
  • Service info: Adjustment of the blue gain.
  • Service info: Adjustment of chrominance/luminance delay.
  • Service info: Adjustment of +B 150V R716.
  • Service info: Adjustment of the green gain.
  • Flyback lines. at top. (with circuit diagram extract)
  • Level adjustment of the sound.
  • AFT (T205) fine adjustment.
  • Service info: Adjustment of the blue gain.
  • SERVICE mode adjustment. (picture attached)
  • VCO adjustment.
  • Service info: E/W 1 adjustment.
  • Adjustment +B 150 V R716.
  • RF AGC R219 adjustment.
  • Horizontal size adjustment.
  • Chroma-luma delay adjustment.
  • +B adjustment.
  • VCO adjustment for picture.
  • G2 adjustment.
  • Does not switch to standby. intermittently.
  • Service info: G2 adjustment. (OTTOVERSAND - DV7036S information)
  • Occasionally remains on standby. No switch on with RC. Appliance operates after mains plug has been pulled out for a short time. (part of circuit diagram displayed)
  • Service info: G2 adjustment.
  • No sound. 1 channel makes loud noise, also in low volume. No stereo indication. Sound present on scart.
  • AFT adjustment T205. (OTTOVERSAND - DV7036S information)
  • No sound. No picture. Standby ok.
  • When aerial connected appliance is locked onto one channel, manual and RCU controls do not function (RCU ok if aerial partially removed).
  • East/West 1 adjustment.
  • Speakers click.
  • No picture. when cold. Vertical fault. after warm-up.
  • Appliance has no proper colour; looks like a demagnetising fault.
  • Q701 fails again.
  • Does not switch on. PSU works in Burst mode.
  • +B 150V adjustment.
  • No picture. No sound. Operating LED switches at start up, but stays red, not green.
  • Arcing.
  • Service info: Adjustment of audio T208 5.74MHz.
  • Trapezoid 1 adjustment (except 21" model).
  • Shuts down. intermittently. (service info for OTTOVERSAND -DV7036S)
  • East/west 2 adjustment (except 21" model)
  • Horizontal blanking phase shift adjustment.
  • Service info: Adjustment of the S correction.
  • Drive blue adjustment.
  • Service info: Adjustment of the blue section.
  • Service info: adjustment of the vertical size.
  • G2 adjustment. (OTTOVERSAND - DV7036S information)
  • RF AGC R219.
  • One colour missing.
  • No audio. No picture. (with circuit diagram extract)
  • RF AGC adjustment.
  • Brightness increases and the picture becomes hazy. (picture attached)
  • Service info: Trapezium adjustment 1. (DV7036S tips)
  • RF AGC adjustment. (OTTOVERSAND - DV7036S information)
  • Bright white picture, very faint and speckled in appearance. Only red and blue flecks in test picture.
  • Black screen. Horizontal line.
  • Slow start-up. when cold.
  • Trapezoid picture. at top.
  • One channel crackles softly (fine in mute and without antenna). Very audible in minimum volume.
  • Shuts down. after start-up.
  • VCO T204 for picture. (OTTOVERSAND - DV7036S information)
  • Trapezoid 1 adjustment.
  • Low audio.
  • Power supply hiccups. Does not leave standby.
  • Vertical size adjustment.
  • Trapezoid 1 adjustment.
  • Appliance has Teletext faults when receiving via a satellite system. (with circuit diagram extract)
  • When switching to teletext the picture becomes completely black.
  • Service info: Adjustment of the green section.
  • S-level adjustment R-231.
  • East/West 2 adjustment.
  • Service info: Adjustment of the horizontal amplitude.
  • Service info: G2 adjustment.
  • Instructions on how to activate SERVICE mode.
  • Audio adjustment T208 5.74 MHz.
  • S-correction adjustment.
  • Fault in the power supply: transistor Q701 is defective again immediately after switch on. (picture attached)
  • Q701 S/C.
  • Service info: Adjustment of the vertical phase. (DV7036S tip from OTTOVERSAND)
  • Poor start-up (needs approx 3-4 attempts).
  • Chroma-luma delay adjustment. (OTTOVERSAND - DV7036S information)
  • Dead. Clicks 10 times, short pause, then clicks again without interruption. (service info for OTTOVERSAND -DV7036S)
  • Switches regularly over to stereo and afterwards back to mono.
  • Blue locking point.
  • Vertical lines. Vertical foldover at top and bottom.
  • Adjusting the HF automatic gain control.
  • Cut-off green adjustment.
  • Drive green.
  • Blank raster. (DV7036S OTTOVERSAND repair tip)
  • Grey picture, diagonal stripes and torn edges. (+ extract of circuit diagram)
  • Trapezoid 2 adjustment.
  • Switches off by itself. in standby.
  • Only the standby-led burns. No start up, also no reaction with the remote.
  • Red blocking point.
  • Drive blue adjustment.
  • Horizontal line.
  • Picture shifted horizontally. Colour fault.
  • S-correction adjustment.
  • Vertical symmetry adjustment.
  • AFT adjust T205.
  • Vertical symmetry adjustment.
  • Sound is very loud in minimum position and disappears after cursor is past middle adjustment. Between minimum and middle position, sound increase in volume.
  • Grey and white picture. No sync or TXT activity.
  • Excessive horizontal size. Pincushion distortion.
  • S2 5.74MHz adjustment.
  • Cut-off blue adjustment.
  • Certain stations cannot be reprogrammed.
  • Service info: Adjustment of the vertical symmetry.
  • RF AGC R219 adjustment.
  • Switches to standby. after start-up.
  • S detector 5.5MHz for sound adjustment.
  • Horizontal phase shift adjustment.
  • No red.
  • Drive green adjustment.
  • No program switch over or volume change from front control. Only programmed stations can be selected from front control.
  • No start-up (intermittently).
  • No audio. (service info for OTTOVERSAND -DV7036S)
  • Cut-off red.
  • Adjusting +B 150V R716.
  • No sound. Sound OK via SCART connection. (+ extract of circuit diagram)
  • Dead. after start-up. Standby LED lit .
  • Service info: adjustment of the blue section.
  • Service info: Adjustment of the blue section. (DV7036S OTTOVERSAND repair tip)
  • Adjusting the horizontal amplitude.
  • Ticking noise.
  • Service info: AFT adjustment T205. (OTTOVERSAND - DV7036S information)
  • Picture is too bright. G2 cannot be adjusted.
  • Red drive adjustment. (OTTOVERSAND - DV7036S information)
  • S2 adjustment T208 5.74MHz.
  • Poor or no start-up. Red LED lights, green LED lights up and then goes out. After 10-20 start-up attempts, switches on with E/W-error and functions for 10 mins. Mains transformer buzzes.
  • Stuck in standby. intermittently. LED blinks orange . (DV7036S tips)
  • Service info: VCO adjustment T204 for the picture.
  • Unadjustable sound and stays on max. If the level indicator line at the bottom of the picture is at the half-way point, the sound disappears right up to the end.
  • Service info: Adjustment of detector T206 5.5MHz for the sound.
  • Lines at top of picture. Light or blue picture or no sync or sound too quiet and control cannot be adjusted to quiet after switch on
  • Horizontal amplitude adjustment - Service mode.
  • RF AGC R219 adjustment.
  • Slow start-up. (DV7036S tip from OTTOVERSAND)
  • S-Correction adjustment. (service info for OTTOVERSAND -DV7036S)
  • Service info: Adjustments of the red section.
  • Service info: Adjustment of the horizontal amplitude.
  • Does not detune stations.
  • White screen. Audio and OSD OK .

If OTTOVERSAND DV7036S fails, this information will help you. Here you can only see the symptom list, to access remedies, you must register.

With help of this list a solution is found often when OTTOVERSAND DV7036S fails.


Additionally to repairtips or service information DV7036S is linked to 137 components (IC's and/or transformers) in the Tectra database, through which you can identify electrical compatibilities (crossreferences) in appliances.


Chassis information is available (which chassis is built in into DV7036S ).

EURAS system also knows 147 appliances having the same chassis as DV7036S and can easily list them.

In the repair discussion pinboard for DV7036S there are 10 replies to questions asked about 4 different repair problems.
With access to EURAS you can all read them or enter your own questions and get help for DV7036S from EURAS technicians or other users.

Do you want to see this remedies/cures for repairtips?   Register here for the EURAS System
Please note: access to the EURAS System can be granted only to professional household electronics repair shops/technicians/TV/Video which are authorized for service by a manufacturer, or can prove to be professionally certified to do repairs on electronic appliances. You will be asked for a statement and information accordingly during registration.

If you do not qualify as stated above and you have an appliance that needs technical service, we do recommend you to contact the manufacturer (for example through his website) or go to a professional household/TV/Video electronics repair shop close to you.

Already registered? open DV7036S OTTOVERSAND in EURAS

All details on the EURAS System: English | Deutsch | Français | Italiano | Español | Magyarul | Português | Polski | Română | Greek |


Back to EURAS Homepage >> All manufacturers >> OTTOVERSAND tech tips  











Last updated: 05. Nov 2009 14:27:33 MET, doccode ISO9002AS168EKA200805C [cachelite] EURASMOP

Responsible for the content: EURAS International GmbH, Eime, Germany.
All brand- or productnames are copyrighted by the respective manufacturer of the appliance and are only being used for identification purposes.