KV25E1D / OTTOVERSAND [TV]

• Shuts down. after start-up.
• Appliance starts up, but no LED, no vertical deflection audible and switches off after approx. 10 secs.
• Bright, white picture with flyback lines, switches off after 10 sec. (OTTOVERSAND - KV25E1D information)
• No picture.
• Switches off by itself. after a few minutes.
• No sound on some programs or sound appears later.
• Slight hum from speakers.
• Green picture. Flyback lines.
• Audio plop when switching preset channels. (+ extract of circuit diagram)
• Noisy picture, picture and picture is OK in VHF.
• Red, green or blue picture with flyback lines. (part of circuit diagram displayed)
• Picture switches randomly from large to small format at irregular time intervals.
• Audio fades. after a few seconds. Picture OK .
• Blinking STEREO/NICAM LEDs in standby mode.
• No audio. No picture.
• Picture appears slowly. Audio OK .
• Colour and AFC fault when cold at switch over.
• Black lines at the bottom of the picture, increase with time.
• Test lines in upper picture half can be seen, vertical deflection distorted at upper picture edge.
• Low noise in sound.
• No function. Squeaking sound from power supply.
• No picture ,OSD and Text available. LED blinks 4 times.
• No picture. after start-up. Audio OK .
• No HV. after a few seconds.
• Very dark picture. No sound. Geometry faults.
• Dark picture for half an hour, then picture with poor contrast.
• Switches to standby after a few secs. LED A blinks once, then LED B blinks 4 times and cycle repeats itself.
• Geometry has shifted or appliance does not switch on.
• No or intermittent start-up. Switches off by itself. after a while. (picture attached)
• No picture, only AV OSD. (KV25E1D tips)
• "PROTECT SP" displayed.
• RC unit.
• Intermittently dead.
• No RC functions. (service info for OTTOVERSAND -KV25E1D)
• Picture is black. Menu, OSD, text and sound OK. Channel B LED blinks 5 times.
• Vertical streaks.
• Dead.
• No OSD. Switches off by itself. after a while. (with circuit diagram extract)
• How to enter service menu to adjust geometry.
• RC unit.
• OSD appears in picture for 2 secs as soon as picture appears after switch on then switches to protection mode.
• Poor picture. Low audio.
• A & B LEDs flashing in standby causing appliance to switch on intermittently from standby.
• Comes on for a short time.
• Picture disappears when vertical deflection fails, appliance cannot be switched on then. Protective switching responds at every start up.
• Switches to protection mode. (part of circuit diagram displayed)
• Red picture. Picture too small.
• Reduced vertical and horizontal size. Excessive red.
• Switches to protection mode. after a few seconds.
• Intermittentlly no function at switch on. No display (LEDs dark). If mains plug is removed and plugged in again, PSU starts up intermittently.
• Picture too dark and/or various irregularities in geometry, brightness and volume. Also incorrect PB from the menu or spontaneous menu action. (with circuit diagram extract)
• Poor audio. on the left.
• E/W fault. intermittently. Vertical fault. intermittently. Switches off by itself.
• No colour.
• No function after being switched off and immediately switched on again. Applies to switch off/on with mains switch and from standby.
• Error codes.
• Poor picture. OSD and TXT OK . (with circuit diagram extract)
• Horizontal line.
• No colour in main picture. PIP OK.
• RC unit.
• No picture or picture is dark. No sound. Different geometry faults.
• Q601, Q602, Q615 fail repeatedly at switch on.
• Voltages are too low.
• No picture. intermittently.
• LED A blinks once, then LED B blinks 4 times. Cycles.
• No audio. Poor geometry.
• No Dynamic Noise Reduction setting with software version AE306.
• Flyback lines.
• No RC functions.
• No start-up.
• CRT socket.
• TXT menu corrupted. A number of characters is repeated. (with circuit diagram extract)
• Low contrast. after a while. Flyback lines.
• Stripes and other interference in picture when switching to channels in band III. OK after 6 secs. (+ extract of circuit diagram)
• Starts up, HV builds up which can be heard then switches off after approx 3 secs. No LED display. (+ extract of circuit diagram)
• Horizontal lines in zoom mode.
• PSU starts and switches off immediately. No LED display.
• Raster ringing and H-linearity. (picture attached)
• After setting volume to max, sound drops out, then cannot switch TV back on or it starts up but, if put into standby, does not switch on and, in this case, no front LED.
• Enter service mode.
• Red picture with flashes. Intermittent standby. Intermittent start-up.