KV32WS3D / OTTOVERSAND [TV]

• Starts up, HV builds up which can be heard then switches off after approx 3 secs. No LED display. (+ extract of circuit diagram)
• Dead.
• Bright, white picture with flyback lines, switches off after 10 sec.
• "PROTECT SP" displayed.
• E/W fault. intermittently. Vertical fault. intermittently. Switches off by itself.
• Enter service mode.
• No picture, only AV OSD. (service info for OTTOVERSAND -KV32WS3D)
• OSD appears in picture for 2 secs as soon as picture appears after switch on then switches to protection mode.
• After setting volume to max, sound drops out, then cannot switch TV back on or it starts up but, if put into standby, does not switch on and, in this case, no front LED.
• Green picture. Flyback lines.
• No RC functions. (KV32WS3D OTTOVERSAND repair tip)
• How to enter service menu to adjust geometry.
• No picture or picture is dark. No sound. Different geometry faults.
• Slight hum from speakers.
• Blinking STEREO/NICAM LEDs in standby mode.
• No start-up.
• PSU starts and switches off immediately. No LED display.
• Picture disappears when vertical deflection fails, appliance cannot be switched on then. Protective switching responds at every start up.
• Shuts down. after start-up.
• Picture is black. Menu, OSD, text and sound OK. Channel B LED blinks 5 times.
• Red picture. Picture too small.
• Switches to protection mode. (part of circuit diagram displayed)
• LED A blinks once, then LED B blinks 4 times. Cycles.
• No OSD. Switches off by itself. after a while. (picture attached)
• Reduced vertical and horizontal size. Excessive red.
• Black lines at the bottom of the picture, increase with time.
• Appliance starts up, but no LED, no vertical deflection audible and switches off after approx. 10 secs.
• No function after being switched off and immediately switched on again. Applies to switch off/on with mains switch and from standby.
• Horizontal lines in zoom mode.
• No colour in main picture. PIP OK.
• Audio fades. after a few seconds. Picture OK . (service info for OTTOVERSAND -KV32WS3D)
• No sound on some programs or sound appears later. (service info for OTTOVERSAND -KV32WS3D)
• Very dark picture. No sound. Geometry faults.
• No RC functions.
• No audio. No picture.
• Stripes and other interference in picture when switching to channels in band III. OK after 6 secs. (extract of circuit diagram attached)
• Intermittentlly no function at switch on. No display (LEDs dark). If mains plug is removed and plugged in again, PSU starts up intermittently.
• Red picture with flashes. Intermittent standby. Intermittent start-up.
• No picture ,OSD and Text available. LED blinks 4 times. (service info for OTTOVERSAND -KV32WS3D)
• Switches to standby after a few secs. LED A blinks once, then LED B blinks 4 times and cycle repeats itself.
• RC unit.
• CRT socket.
• Picture appears slowly. Audio OK . (KV32WS3D OTTOVERSAND repair tip)
• Picture too dark and/or various irregularities in geometry, brightness and volume. Also incorrect PB from the menu or spontaneous menu action. (extract of circuit diagram attached)
• A & B LEDs flashing in standby causing appliance to switch on intermittently from standby.
• Colour and AFC fault when cold at switch over.
• Dark picture for half an hour, then picture with poor contrast.
• Low contrast. after a while. Flyback lines.
• Poor picture. Low audio.
• No picture.
• No function. Squeaking sound from power supply.
• Red, green or blue picture with flyback lines. (picture attached)
• Switches to protection mode. after a few seconds.
• No audio. Poor geometry.
• Voltages are too low. (OTTOVERSAND - KV32WS3D information)
• Horizontal line.
• No colour.
• Poor audio. on the left.
• Raster ringing and H-linearity. (with circuit diagram extract)
• TXT menu corrupted. A number of characters is repeated. (extract of circuit diagram attached) (OTTOVERSAND - KV32WS3D information)
• Geometry has shifted or appliance does not switch on.
• Noisy picture, picture and picture is OK in VHF. (KV32WS3D tip from OTTOVERSAND)
• Q601, Q602, Q615 fail repeatedly at switch on.
• RC unit.
• No or intermittent start-up. Switches off by itself. after a while. (extract of circuit diagram attached)
• No picture. intermittently.
• Vertical streaks.
• No HV. after a few seconds.
• No picture. after start-up. Audio OK .
• No Dynamic Noise Reduction setting with software version AE306.
• Poor picture. OSD and TXT OK . (part of circuit diagram displayed)
• Flyback lines.
• RC unit. (KV32WS3D tips)
• Test lines in upper picture half can be seen, vertical deflection distorted at upper picture edge.
• Intermittently dead.
• Comes on for a short time.
• Switches off by itself. after a few minutes.
• Error codes.
• Audio plop when switching preset channels. (extract of circuit diagram attached)
• Low noise in sound.
• Picture switches randomly from large to small format at irregular time intervals.