7000XT / PACE [Sat /TV reception module]

• Occasionally some channels have a rhombic picture. (with circuit diagram extract) (7000XT tips)
• When in standby terrestrial channels have patterning, ok when switched on. (picture attached)
• Adjusting the programmer mode.
• Appliance switches off after 4-5 seconds, then when switched on takes 4-5 seconds to come on. (with circuit diagram extract)
• Sound is low and distorted. (with circuit diagram extract) (PACE - 7000XT information)
• Sound via RF lead is missing, peri audio ok.
• Standby does not function. (part of circuit diagram displayed)
• Sound is missing, only noise. (+ extract of circuit diagram)
• Dead, remains in standby. (extract of circuit diagram attached) (7000XT tip from PACE)
• Does not store programme memory. (+ extract of circuit diagram) (7000XT PACE repair tip)
• Vertical channels are missing. (+ extract of circuit diagram) (PACE - 7000XT information)
• LNB voltage is missing.
• Appliance does not react to the RCU. Test signal present on the screen but no SAT reception.
• OSG has field bounce. (extract of circuit diagram attached)
• No signals, will not switch to standby.
• Extreme patterning on vertical channels, horizontal channels ok. (+ extract of circuit diagram)
• Video is weak with hum, gets better when MOD2 is adjusted, ok via SCART. (part of circuit diagram displayed)
• Intermittent fault - two white horizontal noise bars.
• Intermittent loss of RCU functions. (extract of circuit diagram attached)
• Sound on encrypted channels are missing, when AV source set to EXT V works ok.
• Will not respond to RCU when first powered up. (with circuit diagram extract)
• Stereo sound is missing, mono 1 ok.
• Severe hum. (with circuit diagram extract)
• Intermittent patterning on some channels. (picture attached)
• Sound hissing and distorted on all audio modes except "Mono 3" and "Mono 5". (+ extract of circuit diagram)
• OSG vertical synchronisation is missing, OSG roll. (extract of circuit diagram attached)
• Polarity switching is missing. (part of circuit diagram displayed)
• 18V LNB supply is rippling. (part of circuit diagram displayed)
• Standby LED not lighting. (part of circuit diagram displayed) (7000XT tips)
• Field flicker.
• Lowered RCU range, about 4-5ft. (extract of circuit diagram attached)
• LNB voltage is low. (with circuit diagram extract)
• Intermittently video is missing.
• Vision-on-sound buzz. (with circuit diagram extract)
• No OSD. (part of circuit diagram displayed)
• Dead, intermittently switches to and from standby, resembles tripping.
• No satellite signals, no response to RCU commands. (picture attached)
• Intermittent hum bars on vertical channel.
• No terrestrial TV signals. (satellite ok).
• Set-up bars distort with vertical lines with hum on picture. (part of circuit diagram displayed)
• Intermittently no response to commands from RCU. (picture attached)
• Vertical polarisation is missing. (with circuit diagram extract)
• In some modes, the sound is distorted. (part of circuit diagram displayed)
• Locked out, on and stereo LEDs are lit. (part of circuit diagram displayed)
• Stereo does not function on one channel. (with circuit diagram extract)
• 'Store' function inoperative.
• Video is lost intermittently.
• Vertical striations on picture. (+ extract of circuit diagram)
• Lowered RCU range, about 3-4ft. (+ extract of circuit diagram)
• Dead, locked up, STEREO OK and LEDs are lit. (with circuit diagram extract) (service info for PACE -7000XT)
• Intermittently sound is distorted. (part of circuit diagram displayed)
• 66kHz sine wave on 12V LNB HT rail, symptoms occur at random. (with circuit diagram extract)
• Dead until relay given a sharp tap, then all functions are ok unless the mains are disconnected. (part of circuit diagram displayed)
• Dead. (extract of circuit diagram attached)
• Sound is poor with motor boating effect. (part of circuit diagram displayed)
• Sound via RF modulator is missing. (picture attached)
• Intermittently OSG loses vertical synchronisation, scrambled channels ok. (part of circuit diagram displayed)
• Bars in picture. (7000XT tips)
• Signal is lost intermittently or tuning locks out. (service info for PACE -7000XT)
• Muted sound, mute is not displayed. (part of circuit diagram displayed)
• RCU output pulses are missing. (picture attached)
• No sound, only off tune buzz. (extract of circuit diagram attached)
• Tuning drifts. (with circuit diagram extract)
• Not responding to remote control. (+ extract of circuit diagram)
• Intermittent moving hum bar. (extract of circuit diagram attached)
• Poor audio. (with circuit diagram extract)
• RCU does not function, display is missing but lock and stereo LEDs are lit. (part of circuit diagram displayed)
• No RC functions.
• Hum bar on picture (worse on horizontal channels. (+ extract of circuit diagram)
• Occasional lock-out of functions at mains power-up or when switching on from standby, (especially when pace 109516 Micro has been fitted. (7000XT tips)
• No sound, just hiss. (+ extract of circuit diagram)