MSS1034G / PACE [Satellite reception system]

• Tripping. (picture attached)
• PSU doesn't start up. Ticking is audible.
• Low contrast. No decoder message. (part of circuit diagram displayed)
• Power supply whistles with bad lines across screen.
• Faint and distorted sound from both channels; fluorescent display flickers in time to the sound. (with circuit diagram extract)
• Whining sound. (MSS1034G tips)
• Weak, rolling picture. (extract of circuit diagram attached)
• Dead. Noise from PSU.
• Square pattern of white dots in columns and rows.
• UHF output stuck around channel 21 and does not tune.
• Dead. No display. (MSS1034G tip from PACE)
• Dead or clicking.
• Dead, just row of zeros. (+ extract of circuit diagram)
• Weak, crackling sound. (part of circuit diagram displayed)
• Distorted audio on centre channel with front and rear scratching sound. (part of circuit diagram displayed)
• Intermittently changes channels or volume.
• Horizontal lines (intermittently).
• Evenly spaced dots on picture.
• Colour is overcontrolled, hardly any brightness.
• Dead. after start-up.
• No decoder and channel idents jumps or jitters. (picture attached)
• Intermittently no picture from TV scart socket. (+ extract of circuit diagram)
• No decoder messages. (with circuit diagram extract)
• Changes channels by itself every 20-30 secs.
• No or weak VCR output. (+ extract of circuit diagram)
• VTR recording failure, lines image flicker9ing, sound volume oscillates during PB of video tape. (with circuit diagram extract) (MSS1034G PACE repair tip)
• Servicing receiver.
• Blank screen.
• No front panel display. (extract of circuit diagram attached)
• Vertical black bar moving continuously from right to left.
• Screen displays "motor overload" when positioner used. Receiver functions OK. (with circuit diagram extract)
• Intermittently dead.
• Dead. Ticking noise. (+ extract of circuit diagram) (service info for PACE -MSS1034G)
• No or distorted audio from RF or scart. (part of circuit diagram displayed)
• No or dim display.
• No satellite pictures. (service info for PACE -MSS1034G)
• No operation.
• Dark picture. Audio OK .
• Blue screen. "No signal" message. (part of circuit diagram displayed)
• Vertical white lines on decoded channels.
• PSU ticking. (MSS1034G tips)
• Faulty front panel display. (PACE - MSS1034G information)
• Picture slips sideways when receiver warm. (extract of circuit diagram attached)
• Horizontal streaky picture on whole screen.
• No or weak picture from RF and TV scarts. (extract of circuit diagram attached)
• Muting does not function in timer mode from surround sound speakers.
• Restore factory settings.
• Display slow to appear. (with circuit diagram extract)
• OSD rolling to left side.
• No picture from RF OUT. Picture from SCART OK
• Remains in standby with zeros in display.
• Switches to standby. after warm-up.
• Power supply upgrade.
• Sound distortion at decoder operation on scart socket AV1 and AV2, especially hearable as cracks and crackles via the connected speakers. (extract of circuit diagram attached)
• P flashes below decoder messages on screen.
• No on screen graphins. No decoding. (with circuit diagram extract)
• Whistling from PSU.
• Lines in picture. (MSS1034G PACE repair tip)
• Does not decode most encrypted sky channels.
• Power supply whistles and no decoder messages. (service info for PACE -MSS1034G)
• Dark picture.
• PSU squealing or hissing.
• Poor horizontal synchronisation.
• No surround sound menus.
• "No signal" in display after 30 mins from cold. No decoder messages. (with circuit diagram extract)
• Blue picture.
• Blue screen.
• Fluorescent display shadows. (extract of circuit diagram attached)
• Dots in picture.
• "LNB SHORT" message on screen.
• No sound, picture OK but with high pitch whistle. (extract of circuit diagram attached)
• No OSD.
• SMPS FET S/C.
• No colour.
• Patterning on terrestrial TV.
• No sound on modulator or TV scart, normal sound on VCR scart.
• Unreliable switching between H and V, especially if higher lead lengths. (+ extract of circuit diagram)
• Low contrast. No decoder messages or intermittent decoding. (extract of circuit diagram attached)
• Clock is faulty.
• No function, twittering noise can be heard from the PSU.
• No decoder messages. On screen channel names float horizontally on screen.
• Picture drifts sideways then goes to black and white.
• Poor contrast with dark picture and decoder inoperative. May have rolling picture. (MSS1034G tips)
• No audio. (part of circuit diagram displayed)
• Will not decode Video-Crypt transmissions; no OSD. (part of circuit diagram displayed)
• Not decoding when warm, no decoder messages. (extract of circuit diagram attached)
• No audio via modulator. (extract of circuit diagram attached)
• Blank raster (intermittently).
• Loss of sync on vertical channels. (with circuit diagram extract)
• Only receives vertical channels. (with circuit diagram extract) (MSS1034G tip from PACE)
• PSU whistling or hissing. (with circuit diagram extract)
• Interference lines on picture. Audio possibly affected. (extract of circuit diagram attached)
• Display is dim and sometimes completely fades away.
• No sound or poor sound on modulator and TV scart, normal sound on VCR scart. (with circuit diagram extract)
• Diagonal, dashed lines swirling across picture. (with circuit diagram extract)
• Rolling interference lines in picture.
• Narrow rolling lines in image, rolling slightly bevelled, intensity depends on programS. Also light 25Hz flickering in the whole image.
• "Card invalid" message appears on screen.
• Decoder message is lost after 5-10 mins. (+ extract of circuit diagram)
• Does not REC picture from VCR SCART.