SS9000 / PACE [Sat /TV reception module]

• Blank raster, OSD unlocked.
• Flashing standby LED.
• Picture distorted from UHF and SCART, looks like crushed sync.
• After approximately 1 hour the picture is lost with just a snowy raster remaining.
• Blackened fuse (blasted). (PACE - SS9000 information)
• Poor picture through RF and Video scart. TV scart OK.
• One receiver appears to work but whistle from power supply and lots of radiation causing interference to many TV sets in the surrounding area. (SS9000 tip from PACE)
• Fitting instructions TE-4. (SS9000 tips)
• No signal.
• Video-Crypt decoder does not function or is intermittent.
• Board discolouration under R3 (100K/2W).
• MONO sound is missing.
• Picture is missing on Video-Crypt encoded channels usually when warm.
• No audio. No picture.
• Receiver remains in standby until it warms up then displays a sparkly picture or tuning drift.
• Appliance is dead, standby LED pulses on and off.
• On UHF bottom channels diagonal lines are present especially in fringe areas.
• Noise bars.
• Five or six diagonal lines on picture.
• Graphics roll vertically after warm up.
• Off tune. Black distorted decoder messages.
• Intermittent loss of sync.
• No picture, blank raster.
• Dead. Storm damage.
• Will not switch to vertical polarity.
• No RC functions.
• Vertical roll.
• Intermittently "Card invalid" or "Please wait" message appears.
• LEDs flash randomly then switches off.
• New season 11 card gives card invalid message sometimes.
• Decoding does not function on some channels.
• OSD's sync. drifting.
• Dead.
• Sloping lines in the picture with all programmes and on both polarisation levels.
• No messages from video-crypt decoder.
• PSU tripping, LEDs flashing.
• Picture and OSG are missing, Q27 hot, ok via decoder scart.
• In PSU BUT11 (pos.Q1) fails again and again after replacing. Appliance whistles and BUT gets very hot.
• On Video-Crypt encoded channels, dot noise is present.
• Low contrast.
• Decreased 5V.
• Unlock parental lock without using PIN.
• Swirling dashed lines on decoded channels.
• Signal via UHF modulator is missing, via scart socket ok.
• Incorrect frequency in tuning menu.
• Poor picture.
• 6.5 MHz sound (audio sound carrier) is defective.
• Faint decoder graphics.
• Faint, diagonal lines on Video-Crypt channels.
• Horizontal channels are missing.
• Restore factory settings.
• Horizontal lines over picture, ok when warmed up.
• Sound is weak or missing, could be intermittent.
• Not decoding Video-Crypt channels; all lights on front panel possibly lit plus hum on sound.
• Dimly illuminated standby LED.
• Venetian blind effect on picture.
• No sound in mono mode and only weak, hissy sound in the stereo mode.
• Appliance whistles most of the time at switch on and horizontal lines in the picture, only noticeable in cold conditions.
• Some channels are under incorrect channel number or are missing.
• Inadequate picture and tuning drift.
• No picture (intermittently).
• Low contrast. OSG unlocked and rolling.
• Factory reset at power on.
• Video-crypt graphics unlocked or drifting.
• No picture from modulator, ok on scart
• Video-Crypt is not decoding or is slow.
• Low gain.
• Flickering on satellite pictures.
• R5 overheats.
• No function,appliance remains in standby position (LED lights up).
• Ripple on picture.
• Faint humming on audio.
• TV scart out, when muted sound video content decreases and then disappears.
• Snow on screen and hiss on sound.
• LEDs flashing in sequence at switch on.
• General reset.
• "Card invalid" displayed.
• Pulsing standby LED and T2 is whistling.
• Interference on picture.
• Picture flashes at the top.
• Q1 (BUT11) in the PSU fails repeatedly after replacing. Appliance whistles and BUT gets very hot.
• Wavy or cogging effect on picture.
• Sound is missing, just a hiss, ok via scart socket.
• To unlock parental lock without using PIN. (SS9200). (SS9000 tips)
• Picture is dark, without picture- and sound information, only slight, bright picture background can be recognised.
• Tune and store channels without RCU.
• Picture is missing, OSG ok.
• Appliance is dead, faint standby LED.
• Polarity switching does not function.
• Diagonal dots on picture.
• Intermittent decoding or no decoding.
• Low gain or bad picture.
• Horizontal lines across picture, ok via decoder scart.
• Will not decode on internal decoder.
• No functions. No functions can be selected via the RC.
• Background crackling and hissing.
• Fuse blown but not black.
• Set up channels.
• Signal, video and sound are missing, LEDs are lit.
• Intermittent picture jumping when warm.
• Horizontal streaks on picture.
• Whistling in standby.
• Slight horizontal lines across picture.
• Slow switching out of standby, tuning drift.
• Vertical channels are missing.
• Noise in picture.
• Flashing picture.
• Does not power up with dish connected. Power supply previously rebuilt.
• Streaky and patterned picture.
• Loud whistling in standby and unit is dead.
• Appliance is dead, LEDs are not lit, FS1 ok.
• Appliance is dead, standby LED and timer LED light up.
• Pulsing picture and no on-screen graphics.
• Power supply hisses.
• 9V supply to tuner is low.
• Venetian blind effect in the picture (picure is poor with horizontal lines).
• Colour flashing.
• One station of every channel only; channels change but channel number remains the same.
• Waves and horizontal lines on picture, at switch on.
• Stuck in standby.
• More or less significant undulation on the picture when cold.
• No decoder messages and channel identifications roll up the screen.
• No operation with LEDs flashing in sequence.
• No picture except from decoder scart. Sound OK.
• Picture is missing and raster blank on Video-Crypt channel.
• Downloading the memory.
• Total failure of the SMPS.
• Excessive LNB voltages.
• Picture is missing, looks like tuner fault. LNB voltage ok.
• Humming on sound. (SS9000 tip from PACE)
• Picture has lines.
• Dead, standby and stereo lights lit.
• No picture via RF output. Scart output OK.
• Streaks on decoded pictures.
• Blank raster.
• Appliance is dead, remains in standby, LED is lit.
• Power supply whistles in standby.
• Streaky decoded picture.
• Looses stored channels when mains interrupted.