TX32PK25P / PANASONIC [TV 16:9 from 82 (76)cm picture]

• Noise (crackle) in sound with some cable networks.
• No vertical deflection. Switches to standby.
• White screen. Raster OK . Shuts down.
• Picture fails when cold.
• Line output stage driver Q551 fails.
• Intermittent corner distortion, knocksensitive to digibox.
• Blue or red or green fails after a while. (TX32PK25P tips)
• 10cm black stripe in the middle of screen. Frizzy picture.
• Q503 failure.
• No picture. after a while. No OSD.
• Tuner cannot be synchronized.
• Colour cast.
• Pincushion distortion. Shuts down. after a few seconds.
• Reduced vertical size (after a few minutes).
• Dark screen.
• Brightness varies.
• No start-up. Relay trips.
• Poor picture. Colour fault.
• Self check.
• PSU pulsates.
• Starts up on programm 0 and then only test picture visible.
• No reception on band 1 and 3.
• Picture slightly blue and blue flyback lines.
• Line output transistor fails repeatedly.
• Intermittently no picture. Feature module is knocksensitive.
• Dark picture.
• An approx 10cm wide white vertical stripe at left picture edge. (PANASONIC - TX32PK25P information)
• No red. One colour missing. intermittently.
• Switches to protection mode. after a few seconds.
• Buzzing from PSU.
• Switches to standby (intermittently). LED blinks .
• Excessive vertical size.
• Picture is very bright, OSD as well. No flyback lines visible, brightness can not be adjusted.
• Bright picture. Excessive blue.
• Dark picture, strange colours, incorrect OSD colours.
• Switches to standby.
• Does not switch on. After 3 attempts TV switches back to standby.
• Mains relais dropout. Appliance remains in standby position. (TX32PK25P tip from PANASONIC)
• Noisy sound in STEREO. Unstable STEREO signal.
• Picture is divided with blanking interval in the middle, line tearing, picture temporary black.
• Only UHF channels, band I and III cannot be selected via C and do not appear during ATP search.
• No start-up. intermittently.
• Dead (intermittently).
• Flashing picture.
• Shuts down. intermittently.
• Picture is shifted to the bottom, distorted linearity, 100HZ module intermittently knock-sensitive.
• No vertical synchronisation. via AV.
• Attempts to start up. Relay clicks. LED lights only in standby.
• Switches to standby, switches on again by itself, runs for some time and switches off again.
• E/W fault. Excessive horizontal size.
• No audio. No picture.
• Severe streaking.
• Switches to standby (intermittently).
• "AV" is constantly displayed on upper left side of picture. (TX32PK25P tip from PANASONIC)
• Convergence error.
• Enter service mode.
• Switches to standby. after a few seconds.
• Slow start-up. Switches off by itself. intermittently.
• Picture drops out, dark, possibly knock sensitive in digi module area. (service info for PANASONIC -TX32PK25P)
• Text and OSD red with streaking.
• Picture appears for approx. 2 sec after switch on, then switches to standby and remains there. Can be switched on again from standby, then same procedure.
• 4ch wide green line from the top to the bottom on the left half of the picture. Colour appears fully turned up, picture comes and goes (black) every second
• Red picture. Dark picture. intermittently.
• No or intermittent start-up.
• Picture too narrow, changes when using volume plus and minus.
• Picture rolls and black and white via AV2. Ok via AV1
• Switches off after approx. 15-30 min. and when the picture is bright (relay clicks 1-2 times) and switches on again. Procedure repeats itself, not knocksensitive. (TX32PK25P PANASONIC repair tip)
• Screeching noise from speakers. No volume control.
• Switches to standby. after warm-up.
• Green shadows in picture.
• Switches to standby (after start-up).
• Switches to standby, LED is on and pulsates a little, switches on by itself. Fault occurs after varying operating times
• Program display on screen.
• Intermittently no switch on. Relay switches several times before the appliance starts up. May be heatsensitive.
• No synchronisation, after a few minutes. Blows line output transistor Q551 (2SC5144).
• No picture. intermittently.
• Moiré in picture only in RGB (AV1).
• No picture. after a while. Audio OK .
• Audio distortion. Picture indentation on corners.
• Black screen. intermittently. Audio OK .
• No picture during operation via AV, AV1, AV2 or front AV. Picture OK via RF.