TOP17 / PEACOCK [17" monitors]

• No picture. Green LED.
• E/W fault.
• Horizontal shift cannot be adjusted correctly.
• Abnormal horizontal width. (TOP17 tips)
• Picture too small.
• No display.
• Bright picture with flyback lines. (PEACOCK - TOP17 information)
• No function, slight ticking noise.
• Digital control failure.
• Vertical, dark line on the left picture edge.
• E/W equalisation.
• No vertical deflection. on upper half screen.
• Picture width twitch after warming up.
• Loud clicking.
• Blanking abnormally.
• Intermittently dark picture.
• No function. PSU clicks. (TOP17 PEACOCK repair tip)
• No start-up.
• "S" appears at switch on from powersave.
• No function. No LED. PSU pulsates. (service info for PEACOCK -TOP17)
• No picture. Orange LED is flashing. (TOP17 PEACOCK repair tip)
• B+ 14V adjustment.
• ABL adjustment.
• Dynamic focus is faulty.
• Picture too narrow.
• Line tearing and horizontal phase shift.
• End man fails when switching to standby (normal mode ok).
• Frame is over stretched.
• Streaking in left picture side. (TOP17 PEACOCK repair tip)
• Trapezoid adjustment.
• OSD has different size and different position in varying resolutions.
• Lines flicker on the picture.
• Function of the TRIAC Q907 In the PSU (appliance also runs without).
• Yellow LED.
• Loose contact in the area of the mains switch. (TOP17 PEACOCK repair tip)
• xray-protection activated but no fault present.
• Too bright with flyback lines. Beam spot when switched off. (PEACOCK - TOP17 information)
• No or poor synchronisation.
• When controlling V-pos. only V-size changes.
• Picture too far to the left, H-pos.
• Abnormal blanking
• Jitters and runs through.
• HV adjustment.
• White balance adjustment.
• Only 50% picture width.
• Picture failure, RGB collapses.
• Picture flickers in Dos mode. All other modes ok.
• High voltage fails 1-2 times a day.
• Mode 7 check - 80KHz. (service info for PEACOCK -TOP17)
• No green.
• No picture. No signal" message appears on screen.
• EHT adjustment.
• E/W fault, picture too narrow, picture width control incorrect.
• No picture. LED flashes green.
• Fcc information.
• No sync. and erratic bars at 800x600 and higher.
• Appliance does not always switch on.
• PSU ticks. Dead. (TOP17 tip from PEACOCK)
• Flickers in horizontal amplitude.
• No OSD, geometry is incorrect.
• PSU ticks.
• Raster white balance adjustment.
• Bias voltage for Q403 is too positive. Should be -0.9V is -0.12V. Q403 goes dead after some time.
• Abnormal OSD
• Blue picture with flyback lines when picture is dark or has low contrast.
• Line linearity fault. Picture is very elongated eastwards. (TOP17 tip from PEACOCK)
• Ticks.
• Intermittent line tearing, picture flickers, Picture width reduces.
• No video and power LED.
• Monitor doesn't function without memory and with empty storage. After start up, "No signal" appears on display and display of horizontal and vertical frequency disappears. Display disappears and screen remains dark.
• Horizontal phase adjustment.
• Blue flickers.
• No picture after some time. LED remains grenn.
• Picture drop out OSD ist selected after some time.
• Abnormal sync.
• Colour tinge.
• Power saving functions.
• No raster.
• Only horizontal line in top of the screen.
• East/West amplitude and trapezium cannot be adjusted. Picture width is OK.
• Convergency adjustment.
• No memory.
• No function, green LED.
• No function, yellow LED.
• No synchronisation.
• Ticking from the PSU.
• Colours blooming. (TOP17 tips)
• Black screen.
• Digital control failure.
• Picture green after a while and with flyback lines.
• Picture jitter. Smell.
• G2 voltage is missing.
• No function. (service info for PEACOCK -TOP17)
• Tripping slowly.
• High voltage starts off briefly, then appliance dies.
• Yellow tint.
• Wavy vertical lines at top of the screen at 1024x768.
• OSD failure.
• Dead. LED does not light.
• PSU pulsates. (TOP17 PEACOCK repair tip)
• Picture is distorted. Impossible to call OSD.
• Not picture. Loud click.
• No contrast control.
• Specifications.
• Occasionally bright picture with flyback lines. Knockresistive.
• Picture content is negative.
• Horizontal line, no vertical deflection.
• No function.
• No function, monitor is ticking slightly.
• Reduced horizontal size. (service info for PEACOCK -TOP17)
• Q403 is dead.
• Picture becomes darker till nothing can be seen.
• Won't start up intermittently, or switches off by itself.
• PSU does not start or starts only occasionally.
• Picture content is missing, flyback and spot of light.
• Horizontal width can not be adjusted.
• PSU chirps.
• Line tearing and horizontal phse shift. (TOP17 tip from PEACOCK)
• No picture.
• Horizontal phase shift after appliance has been on for a while.
• Incorrect OSD control.
• No blue.
• Clicking.
• Line tearing, slight pumping. (TOP17 tips)
• Picture runs through vertically.
• Horizontal pos. too far to the left, can be controlled, intermittent line tearing.
• Heat builds up at R499. Q428 and Q429 (rotation) go dead.
• Trps with LED. S/C on 76V line. Kein Blau.
• No degaussing.
• Flyback transformer operating voltage is too low (approx. 7V).
• No function. LED orange.
• Vertical shadow at left hand picture edge. Black picture on OSD.
• Vertical foldover at the top.
• No functions.
• Focus adjustment.
• Switches off from Standby.
• Vertical centre adjustment.
• C491 is incorrect in the circuit diagram.
• Picture too wide and E/W fault.
• Occasionally poor start up or clicks. LED flashes.
• Pincushion adjustment. (service info for PEACOCK -TOP17)
• Vertical-pos. faulty, not enough picture control.
• FCC-ID Info.
• Picture or colour missing
• Dynamic focus check.
• Vertical black line 2cm from left side of picture. Left side of screen to the middle is darker than the right side.
• One horizontal line on screen. (TOP17 PEACOCK repair tip)
• PSU does not work. (TOP17 tip from PEACOCK)
• No build up from 800/600. Picture is too dark.
• Switches into standby mode. Processor without vertical sync. (PEACOCK - TOP17 information)
• Vertical size adjustment.
• Horizontal size adjustment.
• Standard- and user defined graphic modes.
• Picture too narrow and background too bright.
• Vertical, flickering shadow in the left part of the picture.
• Picture is too dark and too narrow. Noises in the appliance.
• Extreme flickering in the picture width after a while and line tearing.
• No picture, slight ticking noise.
• No red.
• Faulty picture width and E/W control.
• East/West and trapezium cannot be adjusted.
• Too small and too tall.
• No EHT
• Vertical foldover on top.
• G1 shakes or appliance blanks. (TOP17 PEACOCK repair tip)
• Red picture with flyback lines. (TOP17 tips)
• No vertical scan or vertical size can not be adjusted. (service info for PEACOCK -TOP17)
• Dead.
• No function. LED flashes faintly.
• Picture is too wide. No East-West correction.
• Brightness adjustment.
• Vertical line tearing. (TOP17 tips)
• PSU doesn't function.
• No parallelogram control.
• Line output transistor fails directly after switch on.
• Rotation adjustment.
• No picture width control, E/W is defective.