1415T / PROLINE [TV]

• Can be switched on via RC after being turned off via RC. Restart only via mains switch.
• Focus problems. No synchronisation. Tripping. (+ extract of circuit diagram)
• Piercing hiss from appliance in operation.
• Switches to standby.
• Excessive blue. (with circuit diagram extract)
• Watery line from top to bottom; approx. 5cm in from left hand side. (1415T tips)
• Sound remains at 0. Volume cursor is displayed but does not move. (picture attached) (service info for PROLINE -1415T)
• Dead. (extract of circuit diagram attached)
• Excessive horizontal size.
• Enable child lock. (service info for PROLINE -1415T)
• Excessive vertical size.
• DP27 blows repeatedly. (picture attached) (service info for PROLINE -1415T)
• Noise from speakers and from the headphones. (with circuit diagram extract)
• Switches to standby then starts up again randomly. After 1 restart out of 3 the picture is snowy and the message "OFF" appears at the level of the channel number.
• No picture. after a few seconds. Dark screen.
• No picture; screen comes on faintly. Sound ok. (1415T tips)
• Volume blocked to minimum.
• Slow to power up. Intermittently remains in standby for one minute.
• Slow start-up. (extract of circuit diagram attached)
• Extremely low tuner gain. (1415T tip from PROLINE)
• Does not switch to standby. (with circuit diagram extract)
• Dark picture. OSD OK . (extract of circuit diagram attached)
• Tripping. LED lights red for 4 secs then green for 4 secs. (part of circuit diagram displayed)
• Tripping. (part of circuit diagram displayed) (1415T tip from PROLINE)
• Stuck in Euro standard. Cannot switch to service mode.
• Horizontal flag effect with poor contrast and brightness. (extract of circuit diagram attached)
• Switches to standby. after a few seconds.
• Blank raster. Coloured lines.
• No operation. (picture attached)
• No reception. in UHF. (extract of circuit diagram attached)
• Method to improve reliability of TL02.
• Activating the install menu.
• Switches on then goes into standby every 6 seconds. (picture attached)
• Enter service mode. (+ extract of circuit diagram)
• PSU works in BURST mode with 1/4 of power.
• Red LED flickering.
• Blue, red and green flashes. (with circuit diagram extract)
• PSU squealing in Standby.
• Dry noise when changing channel. (+ extract of circuit diagram)
• LED alternates red and green every six secs. (part of circuit diagram displayed)
• Procedure to improve 5V power supply on the TXT module. (part of circuit diagram displayed)
• Horizontal collapse. (extract of circuit diagram attached)
• To run PSU on 60W lamp. (extract of circuit diagram attached)
• Dark screen. No audio. OSD OK. OK via SCART.
• Sudden channel switch-over.
• Display "PIN ----".
• No picture.
• Switches to protection mode. at start-up.
• How to enter sub menus.
• Switches to standby. intermittently.
• Stretched vertical size at top. (service info for PROLINE -1415T)
• Standby light flashing.
• No sound. Picture OK.
• No picture. Audio OK .
• Tripping. LED blinking red and green. (extract of circuit diagram attached)
• Noise from loud-speakers during standby. (extract of circuit diagram attached)
• Retrace lines. No audio.
• Disable child lock.
• Small picture. Top half to one side.
• Switches on by itself.
• Displays signal 0.
• Flyback lines. at top.
• Enable Hotel mode.
• Changing the memory circuit IR02.
• Dead. LED blinks .
• Switches to protection mode. after start-up.
• Vertical line. (part of circuit diagram displayed)
• Dark picture. Audio OK . (1415T PROLINE repair tip)
• Thermal noise in the speakers. (+ extract of circuit diagram)
• No CRT heaters. (service info for PROLINE -1415T)
• No start-up. LED blinks . (part of circuit diagram displayed)
• Intermittently attempts to start up but reverts to standby. Picture out of focus and incorrect scan.
• Shuts down. (extract of circuit diagram attached)
• Cycles on/off. (+ extract of circuit diagram)
• Picture shifted to the left. Stretched picture.
• Stretched picture.
• White dots on red or black colour. (part of circuit diagram displayed)
• No RC functions..'PI' is permanently displayed on the left of screen.
• Goes into SAFETY mode anytime after the first 20 secs to 20 minutes. Channel memory loss. (with circuit diagram extract) (PROLINE - 1415T information)
• Blue line in left side of picture.
• Front controls are stuck. RC does not work. Volume control bar always displayed and set to minimum.
• Diode bridge DP01 destroyed. (+ extract of circuit diagram)
• LED lights up green shortly, then red, blinks twice short, 4 times long, constantly repeating.
• Exiting the production mode.
• Horizontal noise stripes white or black in upper and lower part of screen. Black stripe in the middle of screen. Fault appears and disappears when heating
• Picture flickers with coloured OSD (eg from a VCR). (extract of circuit diagram attached)
• Power supply whistling. Red LED lights up for a sec then switches off.
• Relay trips. (picture attached)
• Menu and programs jump.
• Switches to standby 5 to 6 secs, then LED green 5 to 6 secs and becomes red again. Sizzling from flyback transformer.
• No audio.
• No tuning. (with circuit diagram extract)
• BURST mode is activated at 240V. Contrast and brightness are weak. (picture attached)
• Switches to standby (after start-up). (part of circuit diagram displayed)
• Black screen with 4 to 5 flyback lines at the top of screen after 5 to 10 minutes. (+ extract of circuit diagram)
• LED flashes red, it changes to green after several secs. and then switches back immediately to standby.
• Low brightness. Low contrast. (picture attached)
• Weak audio. Distorted audio.
• No sound. Volume is at minimum and it is impossible to adjust it via RC.
• No start-up.
• How to convert to UK standard 6MHz sound.
• Stuck in standby. (extract of circuit diagram attached)