29DF45EB / SABA [TV (Standard)]

• No start-up. Red LED blinks.
• Destroy of DP110. (+ extract of circuit diagram)
• No vertical deflection. Horizontal line. (SABA - 29DF45EB information)
• Vertical fault.
• Appliance starts up but switches off immediately. LEDs are blinking, first twice, then 5 times. This happens 3 times. Appliance cannot be operated anymore.
• Switch on with Pr+ button on front panel, PSU squeal and goes to standby. LED does not flash. (part of circuit diagram displayed) (29DF45EB SABA repair tip)
• Green and red lines in picture, green picture when warm.
• Shuts down. after start-up.
• No functions. (picture attached)
• Shuts down at start-up. No EHT or flashing LEDs.
• Noise when picture is very bright.
• LED flashes red, jumps then to green/red. Geometry OK.
• Switches to standby. intermittently.
• EHT comes up then trips. LED flashes once, then five times. (part of circuit diagram displayed)
• No tele dialog display via control panel or RC
• Stretched picture. Pincushion distortion.
• No start-up. LED is red. Switches shortly on green and then back. Intermittently LED flashes.
• Switches to protection mode. after start-up. (29DF45EB tips)
• Dark picture. Audio and OSD OK .
• No synchronisation. (picture attached)
• No start-up from standby.
• Error codes.
• Poor start up. LED flashes 3 times and 9 times.
• Channel 05 which has been selected appears in position 09.
• Poor start up, LED lights up yellow after switch on.
• Bars in picture. at top. (extract of circuit diagram attached)
• Vertical line. (+ extract of circuit diagram)
• No N/S correction
• Vertical line. in the centre.
• Switches to protection mode. after start-up. Shuts down. after a while. (extract of circuit diagram attached)
• Switches to standby. after warm-up.
• Switched on with RC, LED flashes 2 times, after a short brake flashes 5 times, then goes to standby. (with circuit diagram extract)
• Starts, LED orange, then green. No RC and control panel function. No picture, no sound.
• Slow start-up.
• Picture too big. Picture shifted to the right. (with circuit diagram extract)
• Flyback lines. No audio. (part of circuit diagram displayed)
• Standby LED does not light.
• Buzzing by brighter picture content. (extract of circuit diagram attached)
• Normal TV images are totally disrupted with overshoots and very unstable horizontal synchronisation. Picture is OK via AV on external monitor. OSDs are OK.
• Bars in picture.
• Goes to protection, displays code 27 and occasionally displays code 25 when started up.
• No start-up. Standby LED flashes .
• Picture is stretched towards the top and foldover.
• No start-up. LED blinks .
• Distorted picture. via tuner. No TXT.
• TV starts up normally but after a while goes straight into INSTALLATION mode as if it has a blank EEPROM. (with circuit diagram extract) (29DF45EB tips)
• Picture width changes when adjusting contrast (beam current dependent).
• Intermittently picture runs through, vertical sync jitters and two programs are skipped when changing programs
• Replacing board PD/DVD 20000.
• No vertical synchronisation. after warm-up.
• Switches off by itself. after a few minutes. (extract of circuit diagram attached)
• Switches off by itself. after a few seconds. (extract of circuit diagram attached)
• Does not switch on. Fault 25.
• 2 green and 2 red flyback lines at upper picture edge. (part of circuit diagram displayed)
• Picture takes too long to appear, PSU starts up but picture tube remains blanked. LED initially red then, after approx. 30-40 secs, green LED blinks 5 times (three times), after that picture is OK.
• Slow start-up (after warm-up).
• Three start up attempts, then LED flashes.
• Dead. Error message: once long, twice short. (picture attached)
• Severe hum or rattling from the PSU.
• Switches to protection mode. after a few minutes. (with circuit diagram extract) (SABA - 29DF45EB information)
• Voltage on terminals on capacitor CP110 is sometimes higher than its insulation voltage. (picture attached)
• Switch off after a while, with LED flashing 3 times, then 5 times. (extract of circuit diagram attached)
• Starts up erratically. LED becomes orange then green and orange again.
• LED flashes long-on / short-off.
• Shadows on text and menu, and streaking.
• Video output stage IC (TEA5101A) on CRT board is defective.
• Dead. (+ extract of circuit diagram) (29DF45EB SABA repair tip)
• One line out of two duplicated in mode 4/3. (extract of circuit diagram attached)
• Light vertical band in middle of screen. (extract of circuit diagram attached)
• Intermittently dead. (service info for SABA -29DF45EB)
• Error codes. (picture attached)
• Picture is full of snow (white points) after operation while. Becomes worse with operation.
• Trips after a few mins. Error code 25 and 27 is displayed alternatively. Narrow and jittering picture intermittently in 4:3 mode. (SABA - 29DF45EB information)
• Enter service mode.
• Switches to protection mode. (with circuit diagram extract)
• Can not be switched on from standby via RC and front control after a short while. Via AV input OK. (service info for SABA -29DF45EB)
• LED only flashes.
• Different error codes appear.
• No LED display.
• Slight ghosting to the left. (with circuit diagram extract)
• No switch-on. LED blinks 4 times (6 times).
• Picture gets dark, OSD and audio OK.
• Switches off after a short time.
• Flyback lines. (+ extract of circuit diagram)
• Reduced horizontal size. after a while.
• Picture rotates, especially in TXT. (29DF45EB tip from SABA)
• No start up or picture takes time to appear.
• Switches to protective switching after 30 min. Picture width twitches 30 min. after switching off protective switching.
• How to switch off protective circuit. (part of circuit diagram displayed)
• Ghosting effect. (with circuit diagram extract)
• No picture. Appliance trips and displays error code 35.
• Unable to set 16:9 format, reverts into 4:3.
• TL19 (S20AF) is destroyed immediately after switch on
• Vertical fault. Switches to standby. (extract of circuit diagram attached)
• Horizontal jitter. Switches to standby.
• Switches off after warming up, then starts briefly and switches immediately to standby. (29DF45EB SABA repair tip)
• No audio via internal speakers. Audio present via headphones and phono.
• Starts up when it is switched to standby. (with circuit diagram extract)
• Delay at switch-on. LED blinks quickly.
• E/W protective switching responds wihtout a reason.
• Starts up badly. Standby LED flickers dimly when cold.
• Switches to standby. after start-up. (part of circuit diagram displayed)
• No switch on in protective circuit mode. LED ok.
• Sound/ picture only appear after a long time. Flashes orange/green.
• E/W fault.
• Ringing in picture. (picture attached)
• Activating the install menu.
• Starts up three times then switches off.
• Heat sensitive. (29DF45EB SABA repair tip)
• No sound from the subwoofer. Medium loudspeaker functions well.
• Approx. 5cm wide black bar at lower picture edge. (29DF45EB tips)
• Vertical IC fails after start-up. (with circuit diagram extract)
• Standby LED flashing once every second.
• No start-up, reverts to standby. LED flashes 3X4 times. (with circuit diagram extract)
• Picture becomes darker, colours become garish and flicker a lot.
• Vertical jitter and line foldover. (29DF45EB tips)
• Shuts down. LED blinks . (part of circuit diagram displayed)
• Control blocks after some operation. When fault occurs RED/YELLOW LED flashes 8 times. (part of circuit diagram displayed)
• Lamp test. (29DF45EB tip from SABA)
• Picture takes more and more time to appear when cold. (part of circuit diagram displayed)
• No start up. Orange LED blinks 3 times then code 27 is displayed.
• Shuts down (intermittently).
• Switches to standby after 30-40 mins . Can be restarted with mains switch. (part of circuit diagram displayed)
• Switches to protection mode. at start-up.
• Shuts down. intermittently. LED blinks .
• 4:3/16:9 change-over does not function. (part of circuit diagram displayed) (service info for SABA -29DF45EB)
• No start up. LED flashes once briefly and then for longer every 2 secs.
• Random change of format 16/9. (extract of circuit diagram attached)
• No RC functions. No front panel function.
• PSU does not start up or starts only for a short time and then switches off.
• Switches off after CRT heats up. (picture attached)
• Enable child lock.
• No start-up. No display.
• Error code 27, 45, 47 or 27, 45, 46 after approx.10 min.
• TL010 becomes too hot and fails sporadically.
• Stuck in standby. Error codes 1 and then 5.
• Red LED flashes. Starts after three start attempts. (with circuit diagram extract)
• Shuts down. (picture attached) (29DF45EB SABA repair tip)
• Switches off by itself.
• Horizontal linearity fault. (part of circuit diagram displayed)
• No start-up. (+ extract of circuit diagram)
• No E/W correction.
• Dark picture.
• Uncontrollable programme and volume change
• LED flashes red (approx. 20 times), then lights up constantly.
• Horizontal sync drops out. Picture is reduced with approx. 5cm on the top. No horizontal sync after approx. 30mins.
• No reaction after line transformer flash over. (extract of circuit diagram attached) (29DF45EB SABA repair tip)
• Appliance starts up only after approx. 3 mins, LED blinks, then relay drops out.
• Colour streaks at points where yellow becomes blue or black bars especially on the pattern generators. (part of circuit diagram displayed)
• Switches on for a short time, enters safety mode, then goes to standby. (part of circuit diagram displayed)
• Linearity fault. Picture amplitude too large and E/W distortion cannot be adjusted
• No functions. Red LED blinks.
• Squeal from the PSU after switch on, switches off, LED flashes red.
• Faint vertical lines
• Displays ''P'' on screen.
• Error code 25.
• After 3 attempts of start up, LED blinks 3 and 5 times, 4 times in total.
• Dark picture. after start-up. Reduced horizontal size. No synchronisation. Black screen. after a while. Audio OK .
• Switches sometimes only after 1-2 min. to "ON" from standby. (29DF45EB SABA repair tip)
• Coloured lines. Slow start-up. intermittently. (+ extract of circuit diagram)
• Stuck in standby. (with circuit diagram extract) (29DF45EB SABA repair tip)
• Poor start up when cold. Code 26 and 37 in the error memory.
• TL100 gets too hot.
• Coloured vertical band only on 3/4 of screen in Secam. Picture OK in DVD, PAL or RGB. (29DF45EB SABA repair tip)
• Moire with antenna. (part of circuit diagram displayed)
• Appliance switches on and off after a few mins. (SABA - 29DF45EB information)
• Flashover at high voltage transformer. (part of circuit diagram displayed)
• Vertical foldover at bottom. (+ extract of circuit diagram)
• LED blinks yellow/green at switch on. Picture appears only after approx 30-40 secs. (with circuit diagram extract)
• Red LED flashes once long and four times briefly after switch on.
• Line output transformer fails. (+ extract of circuit diagram)
• Error code 25 after 10 min.
• Exiting the production mode.
• Three faint dark lines on right side of picture via AV input without a signal.
• No picture. (picture attached)
• No start-up. LED flickers .
• Poor PSU start up. (picture attached)
• Switches to standby after 10-15 minutes and shows error code 46.
• RF noise and no picture.