F21182 / SABA [TV (Standard)]

• No line drive. (SABA - F21182 information)
• No picture after a few seconds.
• Difference in audio output level between AV inputs and a TV programme (RF). (F21182 tip from SABA)
• No MONO audio. STEREO OK .
• Channel remains the same after switch over or no reception even though channel is adjusted correctly.
• Looses channels, after a while.
• No picture. No audio. LED blinks .
• No audio.
• Pulsating picture. (F21182 tip from SABA)
• Cycles on/off. after warm-up.
• 5 key keyboard does not function correctly. LED blinks and volume at maximum.
• No start-up from standby with RC.
• Arcing in picture edges.
• No horizontal synchronisation (intermittently). No colour (intermittently).
• No horizontal synchronisation. when changing channels (after warm-up).
• Line output transistor TLO35 shorts at turn-on.
• No picture. after warm-up.
• Switches off after a few seconds.
• Dead. LED flickers .
• Remains in standby after a storm.
• Switches to protection mode. at start-up.
• Loud noises from speaker. Red LED blinks.
• Shuts down.
• Snow in picture. after a while.
• Picture is missing or noisy in HF. No audio. Everything is OK via scart.
• Negative picture.
• Interference in picture. Horizontal stripes. (F21182 tips)
• AFC lock is not synchronised on channels when warm.
• No start-up. Green LED flickers.
• No synchronisation. after warm-up (intermittently).
• LED blinks at switch-on.
• No picture. via SCART. Audio OK .
• Does not tune any channel. (F21182 SABA repair tip)
• Flickering colours.
• No synchronisation. via SCART.
• Vertical bars on screen. Distorted menus.
• No channels. intermittently.
• Blue P in picture.
• Characters appear or channels switch over randomly.
• Horizontal lines.
• No synchronisation. after warm-up.
• Menus are displayed untimely and with random changes. LED blinks. RC adjustment faulty or absent.
• Goes to standby when switched to AV.
• Picture disappears when warm. Picture sync fault, particularly when changing channels. Sound OK.
• No audio. intermittently. Picture OK .
• Enable Hotel mode.
• Switches to standby. (F21182 tip from SABA)
• Automatic tuning runs through without stopping. Line foldover when channel is tuned manually via frequency input.
• No start-up. Standby OK. Standby LED switches off when appliance is turned-on, does not blink.
• Disable child lock.
• No synch after warming up, picture runs through or screen is grey and display = signal=O via scart and tuner.
• No functions. No LED lit.
• No synchronisation.
• Dark screen. No brightness.
• Deflection fault. (SABA - F21182 information)
• Shuts down. after start-up.
• Horizontal lines rolling from top to bottom.
• Poor picture.
• No station found during tuning search. Picture ok during AV. Sound is missing.
• No audio. after a few minutes. No picture. via tuner. OK via SCART .
• No horizontal or vertical synchronization when warm.
• Identical picture on all channels even when changing the frequencies.
• Stuck in standby.
• Stretched picture.
• No picture.
• Shuts down sporadically, mostly during automatic station search, rarely during play.
• Failure of sync. pulses at channel switch-over when appliance is warm. Briefly ok after changing standard.
• Horizontal white lines in upper part of screen.
• No picture. at start-up. No audio (at start-up). Fault occurs intermittently. . (F21182 SABA repair tip)
• Volume level limitation procedure.
• Popping noise from loudspeakers when switching off TV via On/Off switch.
• No RC functions.
• No tuner reception. Picture runs through horizontally, line folds over. (service info for SABA -F21182)
• Switches to protection mode. after start-up.
• No picture. Audio OK .
• Enter service mode.
• No standby output when switching on a peripheric connected to the socket.
• No red.
• Distorted audio.
• Shuts down. after a few seconds.
• Sound disappears when switching over from STEREO to mono. Sound is present if appliance is switched on again. (service info for SABA -F21182)
• No tuning.
• Lines in picture.
• Line amplitude control range improvement.
• No horizontal synchronisation.
• No colour. after a while. No horizontal synchronisation.
• No audio. after warm-up.
• Briefly light, then switches into protection. (SABA - F21182 information)
• No colour.
• Trapezoid picture.
• Switches to standby. after start-up.
• No picture. via AV (after warm-up).
• No start-up.
• Line BU blows immediately after inserting the antenna plug in tuner or even without touching it, but in this case it takes more time. (F21182 tips)
• No HV. (F21182 tip from SABA)
• Blank screen. Intermittent audio. No channel storing.
• No channel tuning. Picture ok with AV input but no sound.
• Factory pincode.
• Menu display appears suddenly et changes randomly. LED blinks. Fault can be adjusted with difficulty or not at all with RC.
• Diode DP028 S/C after start-up.
• Slow start-up. No RC functions. No audio. via AV.
• Relay pulsates. LED flickers slowly.
• Horizontal deflection unit doesn't switch off in standby. Dark picture and whistling sound.
• Hue and brightness oscillate intermittently.
• Low PSU voltages. PSU chirps.
• No picture and sound in HF. Channels run through continuously. Shows "SIGNAL= 0" and screen is blue. Picture and sound are OK via scart.
• No or poor synchronisation (intermittently).
• Excessive vertical and horizontal size.
• Horizontal output transistor fails repeatedly.
• If appliance is switched on with mains switch, voltage flashovers are briefly visible in CRT neck.
• No channels.
• P on display on bottom left side.
• Switches to protection mode. intermittently.
• Audio problem.
• Excessive horizontal size.
• Volume varies in NICAM. No audio in Mono and AV.
• How to clear off band with keys (client code).
• Different menus displayed randomly.
• PSU pulsates.
• Picture missing or drops out at start up.
• Vertical jitter. after warm-up.
• Mains fuse and mains output stage transistor are defective.
• Black band on the right. (SABA - F21182 information)
• No audio.
• Switches to AV, after a while. Black and white rolling bars.
• Switches off by itself.
• Tripping.
• No synchronisation. after a few hours.
• No horizontal synchronisation. intermittently.
• Scart contacts incorrect.
• Lines in picture. intermittently.
• Does not receive all channels. No horizontal synchronisation after a few secs.
• No green.
• Shuts down (after start-up). Raster OK .
• Dead. after lightning strike.
• No picture. Noise at secondary PSU.
• Loud whistling of line output transformer, which disappears when warm.
• Switches to protection mode. (service info for SABA -F21182)
• No power.
• No synchronisation. via AV (after warm-up).
• Red vertical bars on screen and menus distorted.
• Various problems when warm.
• Dead.
• Fails after PSU repair, after a few weeks.
• No start-up. intermittently. Arcing in picture.
• All voltages are reduced by half. (F21182 tips)
• Red colour fades when warm.
• Shuts down. intermittently. (service info for SABA -F21182)
• No start-up. Power LED lit .
• Line output transistor breaks down immediately at switch on.
• How to change language.
• No sound via scart. No reception in HF (sound and picture missing). Fault is intermittent.
• No synchronisation. intermittently.
• Spontaneous menu display and channel switch-over.
• Sound vibrations from subwoofer.
• Shuts down. after a few minutes.
• E/W fault.
• Sound is missing via antenna and SCART. Snow on screen. Picture is OK via SCART. Slight pincushion distorsion.
• Stuck in standaby. LED reacts when pressing PROGRAM (+).
• Intermittent colour after warming up, line folds over and then "No signal".
• Picture divided horizontally into two parts. Upper half is picture content, lower half is black.
• Shuts down. after start-up.
• No colour. only on certain channels. Searches for channels continuously. intermittently.
• No horizontal synchronisation. No vertical synchronisation. TXT OK .
• Picture freezes. intermittently.
• Excessive horizontal size. after start-up. (SABA - F21182 information)
• Pincushion distortion.
• Transistor S2055 is S/C.
• No audio, mostly after a while. Picture may fail after 1 min.
• No start-up. Standby LED is lit when switched on from main switch. LED blinks 7 times when P+ pressed.
• LED flickers continually at switch on.
• No start-up. Standby LED does not light.
• Excessive horizontal size. only on certain channels. (SABA - F21182 information)
• No functions. LED flashes once in a sec.
• No horizontal synchronisation. OSD OK .