FF367 / SABA [TV (Standard)]

• No sound or vision. (extract of circuit diagram attached)
• Primary power supply fails under load. (part of circuit diagram displayed)
• Poor grey scale. Dominates in black and white. (extract of circuit diagram attached)
• No standard switching. Blocked on PAL. (+ extract of circuit diagram)
• Line at the bottom, no picture. Rattling. (with circuit diagram extract)
• Field collapse across centre of screen. Hum bar may drift down screen about 1 hour before field collapses. (FF367 tip from SABA)
• PSU starts up 1 time out of 10. At switch off, green dot lights up and then goes out.
• Dead (intermittently). (extract of circuit diagram attached)
• Random clicks with Nicam sound.
• Various breakdowns due to U1=7V.
• Black screen. All the voltages are correct. The sound, line transformer and the G2 are ok but the screen remains black.
• No sound, picture is ok.
• No picture, picture appears after each channel change then disappears a few seconds later. Sound ok. (extract of circuit diagram attached)
• No raster deflection. No picture, only vague light in background. Looks like coloured spot at bottom of picture. No start up.
• No display on screen. Black line which moves around instead. TXT is not synchronised. When changing channel a black band appears at the top of the screen displaying V1 then disappears. (extract of circuit diagram attached)
• Intermittent switch between programme 1 and AUX.
• Service info: Contrast- and beam current adjustment after replacing chroma video module.
• Bottom of picture stretches intermittently. E/W effect.
• Intermittent colour.
• Shuts down.
• Dead. LED blinks .
• PSU trips 3 times then shuts down. (with circuit diagram extract)
• Maladjusted convergence on the top quarter of the picture.
• Negative picture, striped and running through in UHF. OK in VHF.
• Dark screen with some RGB lines at the bottom of the screen and whistling near the FBT. Capacitor 1000/40V has been changed but fault persists. FBT has been changed but dark screen with hum then goes into safety mode.
• Stops at random, standby LED off. Start up again possible by ON/OFF switch. (extract of circuit diagram attached) (service info for SABA -FF367)
• Automatically comes out of TXT mode leaving a dull, uncontrasted picture. (extract of circuit diagram attached)
• Spare part no. info: Power supply repair kit.
• Red picture (after a while).
• When switching on with RCU, appliance does not react unless you are approx 1m away from it.
• No off-air luma. TXT OK.
• No OSG, (on screen graphics). Although no OSG, picture functions can still be altered.
• Intermittent crackling in the picture (horizontal black lines).
• Failure to change channels, no memory of channel data.
• Picture white out. (service info for SABA -FF367)
• Screen is very snowy.
• Switches to standby (after a few seconds). (picture attached) (service info for SABA -FF367)
• NS pincushion distortion. More at the bottom than at the top.
• Dark picture and no picture content, no display, only standby dot. (picture attached)
• Video disappears and comes back after a few seconds. Sound present. (FF367 SABA repair tip)
• The picture goes wrong all the time in the vertical direction. A black band appears at the bottom. The capacitors at the level of the raster IC are ok. Solder joints have been redone.
• Uncontrollable brightness with flyback lines. (SABA - FF367 information)
• Switches off then starts up again, mostly when cold. When TV works, sound mute and background noise, but sound reappears at channel switch over.
• No red in graphics display. (extract of circuit diagram attached)
• Moire effect and no sound for a few moments. (extract of circuit diagram attached)
• Intermittent sound from right-hand speaker.
• Unable to tune in fully.
• The appliance switches off automatically and loses its station memory.
• Cables to be connected on the vertical deflector.
• Horizontal lines.
• Vertical deflection. Rotating lines in the lower third of the picture.
• Set blocks (operation via RC or via user control only possible, after the set has been switched off and on again by mains switch.
• Appliance switches over between VHF and UHF, instead only noise in the picture.
• Occasionally memorized data of control unit processor is lost at switch on or switch off with mains switch.
• No tape-end shut off, changing IT20 and IR01 does not cure the problem, no reception on all channels only white shimmer.
• Non-linear. Cramped at top. (part of circuit diagram displayed)
• After changing transformer LP03 burns. TL31 disconnected, 7V on DP37 and 145V on DP41 OK. BU508AT5 has been replaced by BU508A but fault still persists.
• No sound or picture. Teletext functions. Static discharge. New appliance.
• No functions. Standby LED lit . (picture attached)
• No FS tuning. (part of circuit diagram displayed)
• Blank screen. Rolling lines around top. (picture attached)
• Intermittent tripping, display ok. Possible start up again via On/Off switch.
• Volume changes by itself or distorted sound.
• After operating for a few minutes, channels 59 and 62 disappear: picture is replaced by snow.
• No video signal. Sound and TXT display OK.
• Scanning on the screen is visible on a part of the screen. The programme number display is correct. (extract of circuit diagram attached)
• No picture. via tuner.
• Part number info: power supply repair
• No RC functions. (+ extract of circuit diagram)
• Appliance has no HF reception. Snowy picture. (extract of circuit diagram attached)
• ICC7 chassis. N/S correction does not function properly. Initially no function. (service info for SABA -FF367)
• No vertical deflection. Burning smell. (+ extract of circuit diagram)
• Rolling colours and white lines. (FF367 SABA repair tip)
• When appliance is switched on by the mains switch, the TV starts up for a moment, then goes into standby. Does not start up from the RCU.
• Picture is very dark. Picture is visible only by the predominant areas of red and blue. (FF367 SABA repair tip)
• Loss of memory when you switch off the TV and in standby you need to be 5cm from the TV to start it up again despite the TV operating well. Battery is ok.
• Spare part no. info: power supply repair kit.
• Intermittently switches off ten consecutive times or just once. Mostly switches on again automatically. No LEDs lit when switching off.
• Intermittent loud "thump" from speaker.
• No picture just scanning lines. Incorrect frame speed. (extract of circuit diagram attached)
• RC part number.
• Low FM audio, high background noise. (service info for SABA -FF367)
• Line output transistor fails repeatedly. at start-up.
• Wavy picture on right side. Switches off after 5 to 10 mins. (with circuit diagram extract)
• HT value.
• No picture only on 3 channels (eg. nothing on 1, 3 and 6 but picture on 2 and 5) after warming up for 10 mins. This problem disturbs other TVs plugged into the same aerial. (extract of circuit diagram attached)
• Crackling, occasionally squealing after operating for approximately 20 mins.
• Sound pulses.
• The video fails with the decoder syster. No problem with the old decoder. (service info for SABA -FF367)
• No PLL locking when the appliance is switched on. The power supply from TDA6316A is 4.4V instead of 5.1V. (part of circuit diagram displayed)
• No sound, no picture. Weak brightness. Flyback lines if G2 pushed. No functions from TV front panel.
• No stereo reception on channel 60.
• Trips then shuts down.
• Blank raster, sound + EHT OK, no r.g.b. Out of IV21 (HA11498). (part of circuit diagram displayed)
• No picture (intermittently). (with circuit diagram extract)
• How to set up SERVICE mode when appliance remains in low range.
• No STEREO reception on channel 60.
• No channel storing.
• 1Khz tone breaking onto NICAM sound. OK in mono mode. (FF367 SABA repair tip)
• Part number info: RC
• Bright picture. Flyback lines.
• Switches off a few times each evening after replacing transformer. Intermittently switches on again after a while. Sometimes needs to be switched on again.
• Tuner cutting out occasionally.
• No audio (after start-up).
• No TXT. Intermittently low contrast picture in TXT mode. (part of circuit diagram displayed)
• Intermittent crackle on sound.
• Service information: Function of E/W stage.
• Picture lacks height "top and bottom " and width "left and right". No correction possible. E/W distortion. (picture attached)
• Resistor RP01 on the power supply module burns.
• Only 1/4 inch of picture at left hand side. Remainder of picture blank. (FF367 SABA repair tip)
• No brightness.
• No or slight sound on the right and/or left tracks.
• Part no. info.: RC.
• No reception. No UHF or VHF. Channels are displayed correctly.
• Thumping noise from one channel at switch on.
• Green screen.
• Channel 60 and high channels flicker. U6 (30V) is low. (extract of circuit diagram attached)
• Occasionally the video signal is reversed. (part of circuit diagram displayed)
• Heavy patterning on picture. Turning colour down patterning disappears, but the B/W picture has silvery effect on white areas.
• Cabinet back cover vibrates at certain audio frequencies.
• No UHF switching voltage or programme reception. (+ extract of circuit diagram)
• RC part number.
• Low FM sound. High background noise.
• Intermittent OSG display and sound is reduced. (+ extract of circuit diagram)
• Intermittent NICAM sound.
• Picture is almost dark, colours are weak and the Y-signal is too weak.
• Vertical roll. (+ extract of circuit diagram)
• The picture only appears after about 3 or 4 minutes and then turns red or blue. (FF367 tips)
• Hum bar. (picture attached)
• Interference in picture. Audio OK . (part of circuit diagram displayed)
• No raster. (part of circuit diagram displayed)
• No centering adjustment toward bottom.
• Reduced field scan 2in scan approx 1/4in from top. 9 white lines within scan. (+ extract of circuit diagram)
• Remains blocked in PAL.
• HT is low at approx. 152V and has intermittent tripping.
• Blank raster. Flyback lines. (extract of circuit diagram attached)
• Functions in Pal but snowy screen in Secam. (extract of circuit diagram attached)
• No NICAM sound. Normal sound OK. (service info for SABA -FF367)
• TP48 fails after a few days. (FF367 tip from SABA)
• PSU fails in various conditions.
• VHF is ok, no UHF or very little. (FF367 tip from SABA)
• Dead apart from "88" in display. (+ extract of circuit diagram)
• No reception. (FF367 tip from SABA)
• Only the green LED on.
• Switches to standby. after start-up (intermittently).
• Only rainbow colours (vertical deflection).
• RC part number.
• The appliance remains in PAL. (part of circuit diagram displayed)
• Colour cuts out occasionally.
• Only a horizontal line at the bottom. (extract of circuit diagram attached)
• Dead. Standby LED does not light. Standby LED lit . No RC functions. (extract of circuit diagram attached)
• No colour (via SCART).
• In time picture increasingly wanders down the screen. (SABA - FF367 information)
• No contrast. (part of circuit diagram displayed)
• Distorted verticals only on top.
• No IF signal from the tuner.
• At switch on RC must be held at least 40cm from the appliance. If appliance runs, all other functions work perfectly from 4-5m away. (extract of circuit diagram attached)
• Does not store programmes.
• Short lived line output transformer. (+ extract of circuit diagram)
• Receives no HF signals. Band switch over is not possible. (+ extract of circuit diagram)
• The very high tension is intermittent.
• Smearing in picture. (extract of circuit diagram attached)
• Loss of sync on teletext. Mix teletext/picture ok.
• Picture shifted vertically. (part of circuit diagram displayed)
• Random OSD characters all over screen. (extract of circuit diagram attached)
• Part number info: Processors
• Random flashing of lines on screen. (FF367 tip from SABA)
• Picture from the bottom to the middle of the screen. Not possible to adjust the vertical amplification. Black screen to the middle of the screen then picture from the middle to the bottom of the screen.
• No picture. Loss of 1 or more colours.
• Reduced vertical and horizontal size.
• Intermittent dead. Can be OK for days. (+ extract of circuit diagram)
• No HT supplies from DP41, DP37 and DP32. (+ extract of circuit diagram)
• Audible whistling from the back of the cabinet. (service info for SABA -FF367)
• Powers up, LED flashing once. (FF367 tip from SABA)
• No PIP.
• Horizontal line runs from top to bottom and distorts picture. (extract of circuit diagram attached)
• Child lock.
• When the appliance switches off, a spot appears on the screen. (with circuit diagram extract)
• Height of picture shifted below centre of screen. (extract of circuit diagram attached)
• Defective frequency plan.
• Poor horizontal synchronisation. when changing channels.
• No channel storing. (with circuit diagram extract)
• Service info: Unlocking the code lock.
• Appliance has no HF reception. Snowy picture. (with circuit diagram extract)
• Red coloured spot at the bottom left of the screen. (FF367 tips)
• No stereo reception on channel 60.
• No TXT (intermittently).
• No high voltage or line signal control. (picture attached)
• Blurry picture.
• Sound pulsing off and on Nicam lights flashing. (FF367 SABA repair tip)
• Intermittent loud distortion, a bit like motorboating. More likely to occur at high volume settings. (SABA - FF367 information)
• Intermittently goes into TXT mode. (with circuit diagram extract)
• Spare parts information - Part reference for TP24 and TL31.
• No horizontal amplification.
• After deprogramming, followed by a reprogramming, TV functions but the channels have each increased by 9 units. Eg.: 2nd channel is 49 instead of 40. Hence it is impossible to receive channel 62.
• Only rainbow effect (picture foldover).
• Reduced vertical deflection. (FF367 tip from SABA)
• Height reduces. Creeps up from bottom. (part of circuit diagram displayed)
• Crackling audio.
• Failure to switch on from standby unless programme "UP" button is used. (SABA - FF367 information)
• Brightness varies. (extract of circuit diagram attached)
• Low brightness. (with circuit diagram extract) (FF367 tip from SABA)
• No picture. No audio (intermittently).
• TP24, TP16, TP19, TP11 and fuse blow. TL31 ok.
• Channels 1, 2, 3 and 4 ok but teletext is green.
• RP42 blowing. (part of circuit diagram displayed)
• No blue. (extract of circuit diagram attached)
• No UHF reception, displays channel.
• No audio.
• Trips after 15-20 mins. (extract of circuit diagram attached)
• No picture. (extract of circuit diagram attached)
• Intermittently when changing channel, black bars and no picture on channel 23. (+ extract of circuit diagram)
• Channel 60 and special channels flicker. U6 (30V) is too low.
• Vertical collapse. (with circuit diagram extract)
• Clicking on NICAM.
• After a storm no sound and no picture. No light, filament lights up, line transformer ok. screen remains dark, light appears at switch off.
• Dark picture with 3 RGB lines. Sound available.
• Black bar. at top and bottom. (extract of circuit diagram attached)
• Tripping. Arcing. Burning smell. (picture attached)
• The power supply blocks.
• Vertical pinching fault on the picture and vertical linearity fault. (+ extract of circuit diagram)
• Does not always start up. Standby light flashes. Loses memory.
• Service info: Function of the E/W stage.
• Switches off by itself. intermittently.
• Faulty TXT. (FF367 SABA repair tip)
• Vertical lines run over the whole screen. (picture attached)
• No stereo LED operation.
• No sound or picture. No digits lit on display except STEREO and STEREO S2 lit.
• Vertical roll. Vertical foldover at bottom. (picture attached)
• Service info: Contrast- and beam current adjustment after replacing chroma video module.
• Receives no HF signals. Tape switch over is not possible.
• No functions. (with circuit diagram extract) (FF367 tip from SABA)
• Picture jitters.
• Picture may distort if TT module fitted.
• Channel tuning possible up to channel 45. 5 is obtained on channel 39 and afterwards no fine tuning possible. Eg. 2 on channel 59.
• No channel storing. (extract of circuit diagram attached)
• Poor quality sound in FM, ok in AM.
• Hum on picture and noisy chopper transformer.
• Vertical fault. (FF367 SABA repair tip)
• TV goes off and switches on again three times then goes into safety mode.
• Fades out or very dim.
• PSU collapses/cuts off. (part of circuit diagram displayed)
• Moire effect in the colour areas.
• Loss of memory. All program sites on C00.
• Various video faults. (part of circuit diagram displayed)
• Loud noises from speaker (at switch-off).
• At start up, time base and EHT for a moment then cuts out. No standby light on.
• No channel tuning in search mode. (SABA - FF367 information)
• Black rapid flashing.
• No tuning possible. Hum in VHF. Channel display correct. (SABA - FF367 information)
• RF14 burns up. (part of circuit diagram displayed)
• Crackling audio. intermittently. (FF367 tip from SABA)
• No sound. No vertical or horizontal scanning. Just a blue line.
• No RC functions. after warm-up.
• Channel raster has shifted by two or more channels.
• No sound and occasionally the mute function is activated.
• Picture appears slowly. (extract of circuit diagram attached)
• Vertical collapse. at top.
• No STEREO reception on channel 60. (picture attached)
• No start-up. (part of circuit diagram displayed)
• No signal or goes snowy after 1 hour. (picture attached)
• Power supply shuts down. Line drive pulls HT down.
• Blocked on channel no 1 in manual and in RCU.
• Accepts channel number but will not tune.
• Spare part no. info: Power supply repair kit.
• TXT functions for only 2 secs on high VHF. Functions OK on low VHF low and S channels.
• Black and white picture if the receiver is on "Auxiliary".
• Faint white lines rolling up and down picture. Slight cross-modulation effect on off-air signal. (part of circuit diagram displayed)
• Picture is too dark - coloured edges on the right.
• IG01 (TDA4950) fails repeatedly. (+ extract of circuit diagram)
• Crackling on Nicam.
• Appliance switches off sporadically and immediately starts again. After 3 times it can only be started by the mains switch. Fault occurs according to the picture content 2 to 20 times per day. (service info for SABA -FF367)
• Occasionally the appliance is blocked. (extract of circuit diagram attached)
• Sound interruption and/or crackling.
• Colour bleeding. (FF367 tip from SABA)
• 3 to 4 pulses of line transformer then nothing.
• Poor base command. TL31 at -0.4V instead of -0.8V, correct format.
• Intermittently switches between programme 1 and AUX. (picture attached)
• No tuning (after a few minutes).
• Drifts at switch on after 2 mins.
• Black lines appear on the screen. (picture attached)
• The channel frequency shifts for 3 seconds then shifts again. (extract of circuit diagram attached) (service info for SABA -FF367)
• Colour bleeding.
• Stuck in standby when switched off into standby using RC.
• No blue. (extract of circuit diagram attached)
• Green picture. (FF367 tip from SABA)
• Colour flashing in and out.
• No signal.
• Line tearing/ragging on TXT and OSD. TV picture OK. (with circuit diagram extract) (SABA - FF367 information)
• Loud noises from speaker (at switch-off).
• Channel raster has shifted by two or more channels. (+ extract of circuit diagram) (service info for SABA -FF367)
• Bright picture after 2 secs from start-up and no contrast. After 5 secs picture is OK.
• No audio.
• Loud crackling noise from right hand loud speaker at switch on.
• White line approx 10 cm from top of picture. Other functions ok.
• No audio.
• Channel tuning number does not correspond to the frequency required. (+ extract of circuit diagram)
• Poor grey scale. TXT too bright. (+ extract of circuit diagram) (FF367 tip from SABA)
• Poor focus on picture or TXT. Low brightness and badly smeared. (with circuit diagram extract)
• Cycles on/off.
• Does not switch standards, remains in PAL.
• The TV locks in low range frequency. (extract of circuit diagram attached) (FF367 tip from SABA)
• Blurred coloured blobs on screen. (extract of circuit diagram attached)
• Chopper transistor is defective intermittently. (picture attached)
• No power supply and the stand-by light is lit on.
• Random clicks with Nicam sound.
• TV deprogrammes, starts up again then remains in PAL. It is impossible to display S2 standard. (FF367 tip from SABA)
• No audio. after a while. No raster. after a while. Trips. Shuts down. (picture attached)
• Channel raster has shifted by two or more channels. (+ extract of circuit diagram)
• Poor chrominance of black/white with colour at zero. (service info for SABA -FF367)
• Service information: Function of the E/W stage.
• In safety mode there is no high level on the Ger. point if the disconnection of the line raster deflector and power supply is correct.
• TP48 fails after short time.
• Anomaly due to built in switch.
• No picture. Lines in picture. intermittently. (part of circuit diagram displayed)
• No picture and screen is dark. Safety function does not work. (picture attached)
• No blue. in TXT. Picture OK . (SABA - FF367 information)
• At switch on by ON/OFF switch EHT is heard for 1 sec. then goes dead. No display, no LED.
• Loss of stored settings: Tuning, picture or sound.
• Dead (after start-up).
• Blows TP24 and/or TL31. (part of circuit diagram displayed)
• Crackling audio. Snow in picture. (+ extract of circuit diagram) (FF367 tip from SABA)
• No picture. Sound will not tune. (picture attached)
• No standard switch over. No SECAM.
• TP24 gets hot and short circuits. Poor base command. (FF367 tips)
• No picture. Rainbow colours in lower picture area.
• Teletext clock stops. Each 5cm high part of the picture is missing. (part of circuit diagram displayed)
• Moire effect in the colour areas.
• Slight picture jitter in the vertical synchronisation. (with circuit diagram extract)
• Functions in PAL. Does not take the Secam standard. (+ extract of circuit diagram) (FF367 SABA repair tip)
• Black, green, pink, blue screen after start-up for 1 min, then goes to normal.
• No text, sound muted. (+ extract of circuit diagram)
• Receives no HF signals. Band switch over is not possible. (picture attached)
• Appliance functions in VHF but not in UHF. Snow is present.
• Loud noises from speaker (at switch-off).
• No picture. There is a white raster on the right of the screen.
• TP24 fails after first EHT pulse.
• Thump from speaker intermittently. (FF367 tips)
• Tripping. (part of circuit diagram displayed)
• Excessive HV. (service info for SABA -FF367)
• Distortion in the south. Distortion starting at both sides and going to a third of the tube. Fault in the shape of a curve whose extremities are the corners of the tube. (+ extract of circuit diagram)
• No TXT. Muted audio. (+ extract of circuit diagram)
• Intermittent NICAM sound. (with circuit diagram extract)
• Rainbow effect on picture. Flyback lines. (extract of circuit diagram attached)
• Blows 1.6A fuse. (+ extract of circuit diagram) (FF367 tip from SABA)
• No line drive. (with circuit diagram extract)
• Popping noise at switch on. (Nicam model).
• Pincushion potentiometer PG08 controls picture width.
• With audio module black picture with unstable green bars. Without an audio module snowy picture but no reception. (service info for SABA -FF367)
• No tuning of channels. Switching programmes OK, but when channel is pressed, channel does not flash.
• White lines in the middle of the screen, which is black. (with circuit diagram extract)
• Flickering on channel 60 and on special channels.
• Incorrect horizontal linearity, right part of test pattern is wider than left.
• Only rainbow effect (picture foldover).
• No clock signal in 14 of the IV21. No Y signal in 41 of the IV21 and no light.
• The appliance switches to BG standard.
• No IF signal from tuner.
• Trips three times at start up.
• Four vertical lines in upper picture area.
• Nicam is intermittent.
• Pulsates once with line transformer then line BU blows and power supply pulsates twice. When line transformer starts up for the first time, arcing between deflector and tube.
• No audio.
• High pitch whistle on sound, varies with volume mainly on IBA transmission but can occur on BBC.
• LED characters are displayed back to front.
• No grey scale. Functions in SCART.
• Black box appears instead of clock on channel change or when adjusting volume on IMC models.
• Loud noises from speaker (at switch-off).
• Diagonal RGB lines across screen. Poor field scan. (with circuit diagram extract)
• Occasionally no start up. Protective circuit sets in. No soft start. (extract of circuit diagram attached) (FF367 tips)
• TV just displays LOCK.
• No synchronisation (intermittently).
• No stereo reception on channel 60.
• Dead. Standby dot lights up for 1 sec. at switch off.
• Empty lines in top part of picture. (service info for SABA -FF367)
• No picture. A flyback is apparent when you increase the G2. (part of circuit diagram displayed)
• Looks like crt low emission. (with circuit diagram extract)
• Field collapse with RGB lines at top of picture. (part of circuit diagram displayed)
• No horizontal deflection (intermittently).
• Sound only at maximum volume.
• Loss of light after 15 minutes.
• The picture jumps when the appliance is warm and moves downwards. (SABA - FF367 information)
• The TV may function for several days then cut out. VHT is present, black screen and the display indicates standby mode.
• Snowy picture. After 3 mins picture returns to normal.
• Channel 60 and special channels flicker. U6 (30V) is too low. (FF367 SABA repair tip)
• Line tearing. (part of circuit diagram displayed)
• Replaced small transformer which was burning but TV remains in standby and FBT crackles for 5-6 secs then nothing. (FF367 tip from SABA)
• Wrong display. Low light with no picture or sound.
• Blank screen with coloured dots/interference and possible smell of over heating.
• Failure of LG11 in line output circuit. (with circuit diagram extract)
• VCR problems.
• Picture shifted vertically. at top.
• Intermittent loss of channels from memory after switching on again. (+ extract of circuit diagram)
• White screen, no picture. At start up displays 1 and after 5 secs 88, no function possible 5V OK, 20V OK.
• Line output transistor fails repeatedly.
• Sound from right channel is missing.
• No or low start-up volts at IL14.
• No brightness (intermittently).
• Vertical rolling, will not lock with adjustment of the potentiometer.
• After two-three hours the sound crackles very loudly. Model (51K5) Nicam .
• Snow in picture. intermittently.
• Picture is split in two like an aerial echo on all channels even on cable channels.
• Blurred colour blobs on screen.
• LED remains on when set switched on. (FF367 SABA repair tip)
• No switching possible in standard LL. (extract of circuit diagram attached) (service info for SABA -FF367)
• No channel storing.
• TL17 shorts at start up. (FF367 tips)
• Hiss in audio.
• Appliance has no HF reception. Snowy picture.
• Blank screen. Coloured spots rising from bottom. (with circuit diagram extract)
• Occasional raster desynchronisation.
• The power supply transformer trembles. (+ extract of circuit diagram)
• PSU does not start up. standby point is visible for a short time.
• Picture is green, red or blue with flyback lines. (picture attached)
• No audio.
• No STEREO reception on channel 60. (FF367 tip from SABA)
• White screen with flyback lines. Beam current limiter fault G2. A450VT has already been adjusted.
• All programme numbers tuned to the same channel.
• Crackle effect on sound. Intermittent lines across picture. (with circuit diagram extract)
• PSU does not oscillate correctly. (with circuit diagram extract)
• Channel display does not correspond to the channels received. eg. displays CH52 when 43 is received.
• Colour cuts out occasionally.
• Colour bleeding.
• No colour (intermittently).
• Cannot change channels. (part of circuit diagram displayed)
• Blank screen with out of focus blob in bottom centre of screen.
• No EHT or power supply when switched on. 7V=6.3V.
• Very faint and bright picture via tuner. Picture ok via scart via a VCR. (FF367 tips)
• Poor channel reception and channels 59 and 62 are replaced by snow. Occasionally reception is correct.
• V2 voltage.
• Blows line output transformer.
• Pincushion potentiometer PG08 acts as width control. (+ extract of circuit diagram)
• No red. (picture attached)
• Voltage U5 21V goes to 35V when appliance is warm. Vertical displacement. The other EHT secondary voltages are stable.
• No sync on TXT and sound. Mixed mode OK.
• Line BU blows after some time.
• No picture. Single lines approx 2ins apart. Raster appears if height or field shift adjusted. (picture attached)
• Sound makes a noise on both channels and is dependent on the volume setting.
• Picture and sound disappear after approx 5-10 minutes. Not heat-sensitive.
• Intermittent trip/chopper failure.
• Wavy ripples from side to side. (picture attached)
• Bright screen for short period of time, after this just snow confusion and crackling noises in sound.
• Protection mode activated. Standby LED flashes . (service info for SABA -FF367)
• The sound disappears when the appliance is warm. (FF367 tips)
• No colour in Secam, ok in Pal. RGB ok.
• No power supply. Standby light comes on then goes off. (FF367 tip from SABA)
• No switch on at all. No standby LED or programme display on front panel. (picture attached)
• Ticking noise on sound and intermittent sound mute.
• Service info: Contrast- and beam current adjustment after replacing chroma video module.
• No switch on. When switching off with mains switch LED switches on then off. (SABA - FF367 information)
• No sound or picture. Dark screen. FBT functions. Filament tube is lit up. In scart with a VCR normal sound but no picture. Raster appears faintly when the TV is switched off then switched on again immediately.
• VHF band 1 fails occasionally. Snow and sizzling in the sound. Band 3 and high channels are ok.
• Intermittent audio.
• When TV is switched on in standard G, standard cannot be modified. (with circuit diagram extract)
• If a channel is programmed, the programme reappears and the appliance goes to safety mode. (picture attached)
• Service info: Contrast- and beam current adjustment after replacing chroma video module.
• No picture or PLL operation. There are vertical interference bars present. (with circuit diagram extract)
• Off-air luminance is missing, text is ok.
• Colour fails occasionally.
• Power supply transistor blows up at switch on. (part of circuit diagram displayed)
• Loud noises from speaker (at switch-off).
• No picture, white screen and there is an erasing problem after one hour.
• White screen. Flyback lines. (FF367 SABA repair tip)
• Picture is dark and no picture content, no display, only standby dot (line drive ok). (picture attached)
• Disable electronic combination lock.
• Line amplitude is too strong and there is a problem with the east/west cushion.
• Ticking noise. Muted audio. intermittently.
• Does not start up, no standby. Voltage on TP48 C 0V, Bet E 7.35V. Voltage 300 on CP03 OK.
• Type of memory battery. (+ extract of circuit diagram)
• Rainbow on the screen.
• Protection circuit comes into force inappropriately.
• No line oscillation. (part of circuit diagram displayed) (SABA - FF367 information)
• No synchronisation. TXT OK .
• S2000 in power supply defective after a few mins.
• Stop function does not function in teletext, but always jumps back to the memorized page. (part of circuit diagram displayed) (SABA - FF367 information)
• No red in picture or TXT. (with circuit diagram extract)
• Occasionally memorized data of control unit processor is lost at switch on or switch off with mains switch.
• Dark screen dark with vertical bright flyback lines. Picture suddenly appears leaving 2" band at top. (extract of circuit diagram attached)
• Picture becomes yellow intermittently. No reaction to shocks. (+ extract of circuit diagram)
• After switch on power supply pulsates three times. (+ extract of circuit diagram)
• No audio. STEREO OK .
• Intermittent field collapse. Bright flyback lines rolling at centre of screen 3ins high. (picture attached)
• Top half of picture has squiggling verticals which alter with field shift/height. Picture may blank out with coloured lines dependent upon vertical shift position, accompanied by rasping noise from PSU!
• Sound is lost intermittently.
• Weak blue until the brightness is turned up, but then blue flares. (part of circuit diagram displayed)
• Standby LED flashing in standby mode.
• No tuning. Channel display flashes. (+ extract of circuit diagram)
• Automatically changes channels and goes into standby.
• No picture. Centre section of white line just visible at top centre of screen. (with circuit diagram extract)
• Dead. Standby LED lit .
• Switching transistor TP24 fails repeatedly.
• Replacement of the diode split transformer in old chassis ICC5 and new chassis ICC5-01.
• No sound except on the headphones and the scart plug.
• No raster with text board fitted. (part of circuit diagram displayed)
• In safety mode after working for a long time appliance trips then stops. Display off.
• Intermittent loss of colour while setting up picture geometry.
• How to disable key code. (FF367 tip from SABA)
• Trips when aerial is inserted. (+ extract of circuit diagram)
• Moire effect in the colour areas.
• A1 voltage.
• Display isn't synchronised and has black horizontal line on picture instead which disappears when pressing TV key on RC but comes back again.
• After working for a while, RVB lines appear at the top of the screen.
• Colour fails occasionally.
• The appliance does not work with the remote control, but requests from the appliance are accepted.
• No or intermittent picture. via RF output. OK via SCART . (+ extract of circuit diagram)
• Dark picture. (+ extract of circuit diagram)
• Contrast is low in text mode, TV and mix modes are ok.
• Switches to protection mode. intermittently.
• Power supply doesn't start up. (FF367 tips)
• No picture (after a few minutes).
• Switches off for a short time then returns on programme 1 (early F15 chassis).
• The 1.6A fuse is open circuit. (+ extract of circuit diagram)
• Blurred picture, fine adjustment does not adjust sufficiently. (service info for SABA -FF367)
• Only channel 21 is received in UHF. Picture and sound ok in VHF. Displays the correct channels.
• Shade gradually becomes purplish. Ok at start up. Degaussing ok.
• No colour. (with circuit diagram extract) (FF367 tips)
• Appliance blocks in PAL. Operates in video cassette and channel. Telecom display is abnormal. L equals sound, H equals light and F equals colour.
• Crackling sound on "Nicam".
• Colour bleeding.
• Colour flashing in and out. (picture attached)
• Does not change channels. (+ extract of circuit diagram)
• White noise only. No channel LEDs. (part of circuit diagram displayed) (FF367 SABA repair tip)
• Excessive green. (picture attached)
• No red in picture or TXT. (+ extract of circuit diagram)
• No picture at switch-on. Sound OK. Picture may return intermittently. (part of circuit diagram displayed)
• Green screen. (+ extract of circuit diagram)
• Goes into safety 3 times.
• No audio.
• Power supply switches off for a short time (hiccup) when channel is switched over. (service info for SABA -FF367)
• The brightness control display may switch off.
• Distorted text page numbers.
• Intermittent power up; line at top. (part of circuit diagram displayed)
• Teletext moves vertically. Appliance functions very well when Teletext is not displayed.
• No brightness. Audio OK .
• Programming impossible but responds in SERVICE mode.
• Spare part info: value of RL55. (FF367 SABA repair tip)
• No signal. after a few minutes. (FF367 tip from SABA)
• When increasing contrast or on bright video scenes, chroma disappears and 1 or 2 vertical fine black lines appear on left of screen.
• No picture. TXT OK . (picture attached)
• No or poor synchronisation. (with circuit diagram extract)
• No sound or picture except in scart. (picture attached)
• Operation OK. Dark screen, no sound. RCU OK. As in AV position no snow or thermal tube noise. (+ extract of circuit diagram)
• At switch on, focus pot arcing and igniting. CRT board and tube ventiduct disconnected but fault persists.
• TV functions but the displays are erased after a few secs.
• No 22V line but ok when DP43 removed.
• Slow start-up. (with circuit diagram extract) (FF367 tips)
• After an hour dark screen, no sound, display is correct. The display remains on the channel selected then a moment afterwards goes into standby.
• TP24 blown when appliance goes into standby.
• No start up. No drive pulse for PSU Pin 7 IC14 (TEA2029). (picture attached)
• Loss of red. (+ extract of circuit diagram) (FF367 tip from SABA)
• Flickering on channel 60 and on special channels.
• Functions well but occasionally picture turns grainy as if there was a reception fault. Occasionally 5 and 6 disappear. IF screening ok.
• TP24 is destroyed, following a circuit break and return to programme 1. (part of circuit diagram displayed)
• No NICAM sound.
• Missing B-Y.
• No UHF, VHF reception. Similar picture without an aerial.
• Stations drift off tune by channel input. Can only be adjusted by fine tuning.
• When cold trips 3 times with crackling in the speaker, then safety mode. When warm trips then starts up. (with circuit diagram extract) (FF367 tips)
• Faulty raster. (+ extract of circuit diagram)
• Back cover anti-vibration kit.
• No tuning. (part of circuit diagram displayed) (SABA - FF367 information)
• Standard does not change. Channel search is ok. (SABA - FF367 information)
• Shuts down. after start-up. (FF367 SABA repair tip)
• No V1, V2 or VS supplies. (FF367 tips)
• Part number info: power supply repair
• No reception and the display is in German.
• Occasionally the picture is red with flyback lines.
• Sometimes the sound mutes.
• Flyback rasters on screen. No picture, no sound. Display on the front is ok.
• Unstable picture. in UHF.
• After replacing IV21, picture is too wide. Slight geometry fault.
• Picture height below the centre of the screen.
• Teletext displays page 100 only.
• Moire pattern. after warm-up.
• Intermittent audio.
• No B-Y. (extract of circuit diagram attached)
• No programming.
• Sound OK on Canal Plus. No luminance when using decoder. (FF367 SABA repair tip)
• Malfunctioning AGC adjustment. (+ extract of circuit diagram)
• Poor vertical linearity.
• Spare part no. info: Power supply repair kit. (FF367 SABA repair tip)
• Poor focus. (extract of circuit diagram attached)
• TP24 is defective. (extract of circuit diagram attached)
• No blue just smeary.
• Start up is difficult and occasionally impossible with the IR remote control.
• Chroma fault in Secam. (with circuit diagram extract)
• Part number info: power supply repair
• No picture, only faint coloured areas. (picture attached)
• Channel 60 and special channels flicker. U6 (30V) too low.
• No picture or the picture blows. (with circuit diagram extract)
• Loud noises from speaker (at switch-off).
• Appliance has no HF reception. Snowy picture.
• Trips 3 times.
• Variable sound and picture crackling with snow.
• After operating for 5 mins in black and white, it loses G2 and turns mauve.
• No sound at switch on. Sound returns when channel is changed. Fault only occurs at start up.
• Shifts 8 channels after being put back into service mode. (service info for SABA -FF367)
• Part number info: processors.
• Sound pops.
• No switch on from main switch or via RC. (FF367 tips)
• Monochrome picture when AUX selected on IMC receiver. (SABA - FF367 information)
• Poor audio.
• Sometimes CTV starts up and functions. When the CTV is functioning, it stops then starts up again all by itself.
• TV cuts out intermittently. No sound. (extract of circuit diagram attached)
• No sound at switch on.
• Loss of red.
• Blanking lines in the top part of the picture.
• No UHF channels. when cold.
• Changes between standby and ON mode. (+ extract of circuit diagram) (SABA - FF367 information)
• Dark picture. Poor adjustment of sound. (with circuit diagram extract)
• Variable sound and picture crackling with snow.
• Power supply of the control micro is too low (micro has been changed). 3 Volts, CTV does not start up.
• No picture content. After switching on bright picture with colour flecks, same picture without HF signal. Sound OK.
• No vertical text lock. (+ extract of circuit diagram)
• Vertical lines are jagged. (extract of circuit diagram attached)
• Goes into black and white, flyback lines then stops. Dead. Starts up again 2 or 3 times then cuts out completely.
• No scanning. When appliance is switched on green bars then they disappear. FBT is ok. Function is ok.
• Signal and sound are missing.
• Shuts down (intermittently). (extract of circuit diagram attached)
• Brightness of display is adjustable. (SABA - FF367 information)
• No UHF or VHF on the tuner. Pin 6 of the UHF on 33V permanently.
• OSD rolls. (picture attached)
• Sound ok, raster blue with flyback lines. (+ extract of circuit diagram)
• Lines in picture. No colour. No RC functions.
• No channel storing.
• No sound or picture. Teletext functions. Static discharge. New appliance.
• Line transformer does not start up. (service info for SABA -FF367)
• The sound cuts out when warm.
• CTV loses its programming when there is a power cut. What is the value the battery must charge at ?
• No TXT. No tuning. No OSD. (with circuit diagram extract)
• Part number info: power supply repair kit
• No picture. No audio. when changing channels.
• Picture is missing, random lines on screen.
• No audio.
• Loss of memory. Crackle in sound. Flashing picture. Distorted µPC. No sound only noise. No stereo reception. Does not always start up. Wrong values which cannot be changed. Wrong colours and distorted PIP-function.
• Occasionally colour fails.
• Excessive brightness. Flyback lines. (extract of circuit diagram attached)
• Replacing BU508, BU508AV, S2000A, S2000A2 and TP24.
• Loud noises from speaker (at switch-off).
• Power supply fuse blown. (+ extract of circuit diagram)
• Sound VHT is correct but there is no picture and the screen is black.
• Reduced horizontal size (intermittently). (with circuit diagram extract)
• The picture moves out of its frame when the appliance is warm.
• OSD doubled in height. (with circuit diagram extract)
• Weak signal. (extract of circuit diagram attached)
• No HF signals received. Band switch over is not possible.
• Impossible to select bands. Tuner UHF OK. OK via scart. Signal present.
• Volume alters by itself or sound is distorted.
• LED display characters are back to front. (+ extract of circuit diagram) (FF367 tip from SABA)
• Black screen. Switches to RGB in Canal Plus. Sound OK.
• No synchronisation. (part of circuit diagram displayed) (FF367 tip from SABA)
• Poor start up, RC must be pressed for a long time. (part of circuit diagram displayed)
• After 5 mins stations disappear. Wrong characters with the volume OSD. Colours and size change.
• No green. (picture attached)
• A useful note with these appliances.
• Occasional tuning drift and breakup of picture. (FF367 tip from SABA)
• No sound via scart and Canal Plus.
• Clicking on NICAM.
• No audio. No picture. (picture attached)
• TL31 heats up and blows after 5 mins.
• No sound. No picture. No OSD. Only purity spots.
• No operation (intermittently).
• RC part number.
• Sound reduction. It sometimes returns when changing channels.
• Power supply BU blows after operating for a short time. (with circuit diagram extract)
• White dotted line appears on the left of the picture in VHF/Band I reception. (with circuit diagram extract)
• TV does not start up. Power supply does not decouple.
• Accepts tuning channel number but does not alter tuning.
• Does not store settings.
• Weak UHF and VHF reception.
• The appliance starts up after a few mins.
• Picture has severe distortion at top and bottom. Changes with line amplitude. (extract of circuit diagram attached)
• Signal and tuning are missing.
• Cannot be switched over from all channels.
• Colour bleeding.
• Only rainbow colours (picture foldover). (FF367 SABA repair tip)
• No audio. after a few minutes. No picture. after a few minutes. (part of circuit diagram displayed)
• Intermittent fault. The TV stops and even the standby light has gone out. Starts up again by itself.
• Appliance trips and shuts down, sound or raster is missing.
• Line tearing in TXT.
• AGC problems. Poor reception. (picture attached)
• Popping noise from speakers at switch on.
• No stereo reception on channel 60.
• No field scan when switched on from cold. Field output thyristor DL21 may not operate. (part of circuit diagram displayed)
• Unstable operation of the oscillator.
• No start up with RC. Functions OK with RC when switched on manually.
• There is 145V instead of 170V and there is too much L/T amplitude. (FF367 tip from SABA)
• Interchangeability of teletext boards between chassis ICC5 and ICC5.01.
• Picture geometry problems.
• Poor picture and sound synchronisation. Moire effect on the picture. Occasionally there is no sound or picture.
• Loss of channel 1.
• Spare part no. info: Power supply repair kit.
• Fuse and power supply transistor defective.
• At switch on, raster linearity fault for 1-2 minutes.
• Coloured flyback lines over picture. (picture attached)
• Trips 3 times then shuts down. (+ extract of circuit diagram)
• Picture reduced to the top half of the screen with a linearity fault. Light pulsates and flyback raster on some lighter pictures. Scanning returns to normal occasionally when changing channels. (part of circuit diagram displayed)
• OSD only functions in PAL.
• U5 voltage incorrect.
• Remains in PAL when cold.
• Occasionally dead, then snow. Goes into standby by the RCU and only starts up again after 30 secs.
• Part number info: processors
• Line output transistor TL31 fails. Works for days sometimes weeks. (part of circuit diagram displayed)
• Teletext graphics are incorrect with black bars down the screen. (FF367 SABA repair tip)
• Reduced horizontal size. (extract of circuit diagram attached)
• No picture and no direct display of the channel possible. Picture shifts.
• No start up. The standby light comes on then goes off straight away when stop function is requested. ***MODIFY PAGE ACCORDING TO FRENCH.***
• Terrestrial channel in the background of a satellite transmission.
• Intermittent colour when setting picture geometry.
• At switch off, loud noises from the speaker.
• No channel storing. (extract of circuit diagram attached)
• No vertical deflection. intermittently.
• Low gain. (SABA - FF367 information)
• PSU trips three times then powers down. Standby LED lit briefly at switch on. (picture attached)
• No sound or signal.
• No N/S correction. (picture attached)
• Desynchronisation of the OSD when changing channel or "display line adjustment" display circulates on the screen and is illegible. (extract of circuit diagram attached)
• No picture. Horizontal collapse. Audio OK . (extract of circuit diagram attached)
• Channel numbers cannot be entered.
• Smokes then switches off. (picture attached)
• Horizontal collapse. (part of circuit diagram displayed)
• Intermittently blocks in AV. The channels remain displayed on the display.
• Only colour info visible. No Y signal.
• Unfocused raster. (part of circuit diagram displayed)
• Service info: Unlocking the code lock.
• No red on TXT. Picture OK.
• Intense patterning on picture, silvering effect on all white areas.
• Intermittent colour.
• No audio. (service info for SABA -FF367)
• Receives no HF signals. Band change is not possible.
• Display shows channel only. (part of circuit diagram displayed)
• Only white noise, channel LEDs do not light up.
• Lines from top to bottom of screen.
• No reception or sound. Brightness is OK.
• Relaxation of the power supply. If point 8 of the THT is opened, the 110V voltage returns. (+ extract of circuit diagram) (service info for SABA -FF367)
• Line transformer vibration on white pictures.
• In cold state of the television receiver, the thyristor DL21 (ESM740G) in the vertical stage may not switch on. (with circuit diagram extract)
• No sound. Hiss only.
• No Y-picture or colour.
• Interchangeability of teletext boards between chassis ICC5 and ICC5.01.
• Distorted sound, balance off centre, supersound and NICAM defective.
• No picture. White screen with an oscillating interference signal. (extract of circuit diagram attached) (FF367 tip from SABA)
• Display flashes and turns dark. Channel displayed but cannot be adjusted. RC OK. (FF367 tip from SABA)
• All adjustments at zero (brightness, colour, contrast). Channels are also at zero. Adjustments can be made at 50 but they are lost during standby or ON/OFF. (picture attached)
• PSU and high voltage pump three times. (picture attached)
• No Canal Plus decoding.
• No SECAM. Only PAL, even adjusting it to SECAM F. Remains in PAL. OK via scart.
• Double picture. Picture shifted 1mm.
• Line whistle. (picture attached)
• Vertical lines pulling at the top of the picture.
• No search possible, snow.
• No horizontal deflection.
• Channels have shifted (test picture on channel 33, channel no. 42 displayed).
• Unable to enter channel number. (picture attached)
• Volume changes by itself or distorted sound.
• No channel storing.
• Picture detuned on all channels.
• In cold state of the television receiver, the thyristor DL21 (ESM740G) in the vertical stage may not switch on.
• TL29 fails in B and C after start up.
• Channel raster has shifted by two or more channels.
• Only rainbow colours (picture running through).
• Narrow horizontal lines in the picture. (extract of circuit diagram attached)
• Brightness varies until there is a dark picture.
• Sharp picture but negative and pale. Service mode OK.
• Picture shifted vertically. at bottom. (+ extract of circuit diagram)
• Rainbow effect on lower picture edge, otherwise no picture.
• Corrupted TXT page number. (with circuit diagram extract)
• Vertical interference line (1/2cm wide) at left of picture on low channels. (SABA - FF367 information)
• Colour cuts out occasionally.
• Hum bar drifts down picture then field collapses after approx 1hr. (picture attached)
• At switch on, after 15 secs, dark screen with a few horizontal white lines between the middle and top of screen. Picture returns with geometry fault, if PG08 is turned. Sound ok.
• No audio. (part of circuit diagram displayed)
• Black raster. 1/2in of picture. (+ extract of circuit diagram)
• After two minutes graphics appear on screen showing "nicam and mono" flickering and affecting audio reception. (+ extract of circuit diagram)
• Intermittent motorboating noise on sound.
• The channel display is incorrect (eg.when receiving channel 36, the display shows channel 38). (extract of circuit diagram attached)
• Faulty raster. Vertical jitter. (picture attached)
• No function. PAUSE LED is lit.
• Dark picture with bright lines. Sound OK.
• No sound or picture. Dark screen. In scart with a VCR, normal sound but no picture. Raster appears faintly when the TV is switched off then switched on again immediately.
• Flickering on channel 60 and on special channels.
• Part number info: processors
• General information.
• No picture and strange glow at top of picture. (extract of circuit diagram attached) (SABA - FF367 information)
• Intermittent loss of raster at switch on with white lines at the top. Flyback raster when acting on PG08 or when going to AV.
• Only rainbow colours (vertical deflection error). (part of circuit diagram displayed)
• U system voltage table. (FF367 tip from SABA)
• Poor Teletext page number.
• Unstable picture. Horizontal interference on the screen. The sound crackles.
• Mains transistor TP24 (S2000AF) blown straight after being turned on.
• Poor audio.
• Channels 1, 2, 3 and 4 ok but teletext is green. (picture attached) (service info for SABA -FF367)
• Loses programmes. Sometimes does not start up. Wrong display.
• High pitch whistle on sound, varies with volume mainly on IBA transmission but can occur on BBC as well.
• Volume changes by itself or sound is distorted.
• No display. after a few seconds. AV OK . (service info for SABA -FF367)
• Approx 3cm at top of picture has coloured lines. (+ extract of circuit diagram)
• Flyback lines. at top. (+ extract of circuit diagram)
• Dead (after lightning strike). (+ extract of circuit diagram) (FF367 SABA repair tip)
• No NICAM sound, normal sound ok.
• Poor colour.
• Stuck in standby. (+ extract of circuit diagram)
• Picture appears to pulse or flutter.
• No colour. (picture attached)
• Goes into standby and cannot be turned on using RC; OK when channel up button on set is pressed for approx 8 secs. (with circuit diagram extract)
• Dead. (part of circuit diagram displayed)
• Top half picture blank, bottom half bright flyback lines.
• Power supply switches off, breaker circuit doesn't start up even with continuous attempts to start up.
• Program site is displayed but the appropriate picture does not appear. If fine tuning is activated, picture appears.
• Pincushion distortion. (+ extract of circuit diagram)
• Pop at switch on.
• Fuse FP05 (1.6A) blows sporadically without any obvious reason after an extended running time (approx 1-2 months). After replacing appliance runs perfectly again.
• Does not start up. 142V on line collector S2000, the standby LED scarcely lights up when appliance is switched off, a priori no diodes s/c. (service info for SABA -FF367)
• Very poor colour. Looks like indent fault.
• Colour drop-out.
• No colour in SECAM. Functions in PAL via scart. (service info for SABA -FF367)
• No sound or raster. (+ extract of circuit diagram)
• Hum bar. Vertical collapse. after warm-up. (picture attached) (FF367 SABA repair tip)
• Poor start up performance of the power supply. (part of circuit diagram displayed)
• Switched mode chopper transistor blows fuse at switch on. (picture attached) (FF367 tip from SABA)
• Only rainbow effect (picture foldover).
• No colour when cold.
• Appliance has no HF reception. Snowy picture. (with circuit diagram extract)
• Part number info: Processors
• Poor reception. Pieces of OSD appear erratically on display. No menu display.
• No RC functions (intermittently). (+ extract of circuit diagram)
• Arcing at switch on. CTV trips 3 times then stops.
• Picture has shifted horizontally. Sound available only every 2 secs. Picture and sound OK via AV.
• Flickering picture. No picture. after a few minutes. (+ extract of circuit diagram)
• Sporadic hum from speaker. Hum disappears when switched off and on. (picture attached)
• Trips after warming up for a few minutes. (with circuit diagram extract)
• Storage battery explodes HD404918 A08
• Disable electronic lock.
• Ringing in picture. on the left. (with circuit diagram extract)
• No HV. (part of circuit diagram displayed)
• Improving the reliability of TP24 (S2000 or BU508). (extract of circuit diagram attached)
• No normal sound just white noise. NICAM OK.
• RC part number.
• No channel storing.
• No HV (intermittently). (FF367 tip from SABA)
• Moire effect in the colour areas.
• No sound. Good picture then goes into stand-by after 5 mins then starts up again after pressing a channel number 3 or 4 times.
• When going into standby with RC, impossible to start operating again with the RC and light flashes after a few moments. (picture attached)
• No voltage on varicaps. (picture attached)
• Blue picture. Line at top. (with circuit diagram extract) (service info for SABA -FF367)
• NICAM sound drops out. NICAM indicators flash as sound cuts out.
• NICAM sound crackles and is distorted.
• Replacement of uP HD 404019 A05.
• Constant red, green and blue line scanning.
• When switching on snow with moiré on all stations. It seems as if the stations are way out. After running for a short time picture is ok.
• Ticking noise on sound with intermittent mute.
• No picture. intermittently.
• Only rainbow colours. Picture foldover. (+ extract of circuit diagram)
• Some text pages not available. (picture attached)
• Intermittently noise breaks through on NICAM sound.
• Intermittently no adjustment of sound with RC. RC OK. IR receiver OK.
• Echo on picture.
• No standby light when put into standby and impossible to start up again, except when starting up from the control panel.
• VHF band 1 occasionally fails. Snow and sizzling noise in sound. Band 3 and high channels are ok.
• No picture, only flyback raster visible with distorted raster. (FF367 tip from SABA)
• Power supply goes into safety mode. (part of circuit diagram displayed)
• Reduced vertical deflection. at bottom.
• Volume changes by itself or sound is distorted.
• Intermittent unlocked colours.
• No tuning.
• Colour fails occasionally.
• Will not go into standby cleanly when hot, it will pulse between standby and on 5/6 times before finally staying in standby.
• Occasionally there is a luminance problem when warm. (part of circuit diagram displayed)
• No audio.
• Terrestrial channel in background of Satellite transmission. (FF367 tips)
• No sound on NICAM sets.
• Memory loss.
• Sound is very distorted on both channels when cold like when warm. All the other functions are normal.
• Memory loss. after a while.
• Occasionally static discharge.
• Channels drift after start-up. (part of circuit diagram displayed)
• No TXT. Command is received but not carried out. Picture does not turn black.
• Intermittent large noise bands. Picture OK via SCART socket.
• There is a moire effect on the screen for a short while and no sound.
• Service info: Contrast- and beam current adjustment after replacing chroma video module.
• Sound pops.
• Sound distorted when volume increased.
• Colour picture via the tuner, black and white in scart.
• Field collapse to approx 12 lines in centre of screen. (+ extract of circuit diagram)
• Lines in picture. at top. (part of circuit diagram displayed)
• Thin black lines across picture. Intermittent arcing. (part of circuit diagram displayed)
• SAT switch over is defective.
• Severe patterning like white sparklies. (picture attached)
• Picture jumps and vertical distorsion according to video content, mostly on second station, channel 21. Intermittent fault.
• With a 220V/100W load or with line connected, power supply stops but functions with the line disconnected.
• Does not switch on and no standby.
• No fastext. Normal text OK. (+ extract of circuit diagram)
• Programme indicator "1" flashes but will not tune.
• Loud tripping noise from the output stage. Trips three times then dies. (picture attached)
• No picture. via RF output (intermittently). OK via SCART . (+ extract of circuit diagram)
• Power supply does not start up. No standby. 5V present. IR01 is ok. TEA2029 is ok. No oscillation on the primary circuit.
• Moire pattern. when cold.
• Picture height is shrivelled to 10cm. A few rolling horizontal lines in the middle of the picture.
• Protective circuit malfunction.
• No focus. (extract of circuit diagram attached)
• Brightness problem, display works well but no variation. Contrast and colour ok. Clock data and enable data ok. (FF367 tips)
• No sound or picture. Scanning not very apparent, greenish, flyback lines. Functions occasionally in scart.
• Mains switch does not lock on.
• No tuning, OSD or TXT.
• No colour.
• Occasionally memorized data of control unit processor is lost at switch on or switch off with mains switch.
• Power supply BU blows after 10 secs. Correct power supply attempted with line transformer load disconnected.
• After changing the CRT base, there is HT flashover which appears as crackling sound and flickering picture.
• No vertical synchronisation. (with circuit diagram extract)
• The PSU switches 3 times, line transformer, E/W diodes, U4 and U5 are ok.
• Trips. NICAM lights appear to flash. (+ extract of circuit diagram)
• Partial blanking of video info. (part of circuit diagram displayed)
• Frame jumping or twitching. (+ extract of circuit diagram) (FF367 tips)
• Remote control operation problem. Microprocessor memory and new quartz. New remote control. Remote control information reception on the microprocessor.
• Snowy picture after 20 mins. (with circuit diagram extract)
• Display flashes in STAND BY and the TV does not start up, even with the RCU. Occasionally it starts up when you activate P and VOL, and press On/Off several times.
• Service info: Function of E/W stage.
• Incorrect TXT graphics. Black bars displayed down screen.
• Switches to protection mode. after start-up.
• Appliance trips or RL44 burns up. (FF367 tips)
• Reduced width and width control has little or no effect. (+ extract of circuit diagram)
• The picture amplitude is too small. The whole of the picture is recorded in the lower half of the screen.
• Poor reception. in UHF. Hum in audio. (FF367 SABA repair tip)
• No signal.
• Channel programming is impossible. The channels are defective on the display.
• Horizontal rotating lines approx 5-8cm high. (+ extract of circuit diagram)
• No picture no sound, EHT ok. (with circuit diagram extract)
• Occasionally memorized data of control unit processor is lost at switch on or switch off with mains switch.
• Starts up three times then switches off.
• All rails are very low, 3V on 158V (158 reads 500 Ohm).
• Channel indication flashing 1, will not tune or adjust.
• No colour (intermittently). (part of circuit diagram displayed)
• No start up of PSU. 300V present. (service info for SABA -FF367)
• No channel storing.
• Occasionally memorized data of control unit processor is lost at switch on or switch off with mains switch.
• Tuning drifts (after a while).
• Switches to standby (intermittently). (+ extract of circuit diagram)
• Switches on, but HV does not build up.
• Impossible to go into SECAM. (picture attached)
• RV82 (10R) on tube board blows repeatedly.
• Code lock.
• The display indicates 88.
• No audio.
• White wavy line across the middle of picture 1in wide. (with circuit diagram extract) (SABA - FF367 information)
• Spare part no. info: Power supply repair kit.
• RC part number.
• Intermittent audio.
• Channel raster has shifted by two or more channels. (with circuit diagram extract)
• Intermittently unlocked colour.
• Menu display in wrong language.
• Vertical stability fault. Picture revolves as it moves up the screen. No sound with scart. TV goes into standby after 5 mins as if there were no transmission.
• No colour in PB from a Ferguson FV26D VCR when VCR is positioned under the TV.
• Screen is blank with rolling lines at the top.
• Loud crackling noise from right hand side at switch on.
• In the picture appear black lines similar to lightning. Fault is not visible via scart.
• Low HV. (with circuit diagram extract)
• Cut-off adjustment.
• No LL' switching when you press C of the remote control.
• How to disable key code.
• No blue on TXT. Picture OK. (extract of circuit diagram attached)
• No correct reading on the display.
• Blank raster. White and RGB lines at bottom of screen. (part of circuit diagram displayed)
• Dead. Standby LED flashes . (picture attached)
• Spitting noise from speaker. Intermittent digital sound. NICAM LED's go out.
• Loses channel 1.
• Rolling coloured and white lines. (extract of circuit diagram attached)
• Difficulty starting up. When started up it functions for a few mins. (extract of circuit diagram attached)
• No sound. TV cuts out after 10 minutes. Sound board OK.
• No start-up (intermittently). (extract of circuit diagram attached)
• Picture appears after 1.5 mins when cold and after 25 mins when warm (part of circuit diagram displayed)
• Part number info: power supply repair
• Picture interference at the top and bottom, which changes with the line amplitude. (+ extract of circuit diagram)
• Black patch on left hand side, approx 1/3 of picture. (with circuit diagram extract)
• No stereo reception on channel 60. (+ extract of circuit diagram)
• No audio.
• No picture appears in PAL.
• Horizontal line. at top. (+ extract of circuit diagram) (FF367 SABA repair tip)
• Occasionally colour fails.
• Snowy raster.
• Line output transistor S/C. (picture attached)
• No AGC.
• No TXT, although control shows appliance is in TXT.
• Picture lacks blue colour until the brightness is turned up, then blue flares across the picture. (+ extract of circuit diagram)
• Noisy sound on both channels (dependent on the volume setting).
• Moire effect in the colour areas.
• Red raster. Flyback lines. (extract of circuit diagram attached)
• Pulsating picture. (with circuit diagram extract)
• Intermittent flashing lines on screen. Picture OK with scart input. (part of circuit diagram displayed)
• Service Info: Unlocking the code lock.
• Power supply switches off.
• Intermittent loss of colour. Worse when warm.
• Receiver goes off after tripping of power supply.
• Deprogramming due to static loads.
• Picture visible in one inch strip at left side of screen, rest is blanked. (+ extract of circuit diagram)
• Displaced channels eg. M6 on channel 41 instead of 50. No channels between channel 21 and 36. (with circuit diagram extract)
• No picture, sound o.k. High voltage and power supply in good order.
• No horizontal synchronisation. when changing channels. (+ extract of circuit diagram)
• No colour, no brightness. Only one colour on TXT or certain colours are missing.
• No picture. Audio OK . (picture attached)
• At switch on, goes into standby and impossible to get out of it. After 5 mins, appliance starts up by itself and functions well. If stopped for a few secs, it works normally.
• Vertical displacement of approx 5cm towards the top of the screen when warm.