HRC1000 / SABA [TV]

• RC part number.
• Housing cracks - temperature sensitive.
• Colour flickers. Brightness varies.
• Switches to standby. after start-up. (extract of circuit diagram attached)
• Vertical line. Horizontal output stage ticks.
• Intermittently purple flash on picture. (picture attached)
• Dark green with streaking. (picture attached)
• Trips (after warm-up). (extract of circuit diagram attached)
• Switches to standby. after a few minutes. (+ extract of circuit diagram)
• Line output transistor D1446 blown repeatedly. (extract of circuit diagram attached)
• DL09 blown. Narrow picture vertically with foldover. TDA8178 has been changed, OK for a few days then again compressed picture with foldover. TDA8178 is defective. (part of circuit diagram displayed)
• No OSD. (+ extract of circuit diagram)
• PSU pulsates. (part of circuit diagram displayed)
• Lines in picture. (extract of circuit diagram attached) (HRC1000 tips)
• Line BU clicks. (extract of circuit diagram attached)
• Gull wing distortion. (extract of circuit diagram attached)
• How to exit Service Mode. (HRC1000 tips)
• No green. (part of circuit diagram displayed)
• Blue-green flashes every 30 seconds during PB via scart.
• Blue flooded picture. Flyback lines. (extract of circuit diagram attached)
• Trips (after start-up). (with circuit diagram extract)
• Regulation is defective. (with circuit diagram extract)
• Switches on for a short time. Red LED lights for 5 secs, then goes out again.
• Horizontal output transistor fails repeatedly.
• If started with RC, protective switch starts up. Intermittently it happens when it is turned on from mains switch, too. (+ extract of circuit diagram)
• Pincushion effect. Unable to adjust using E/W adjustment potentiometer. (with circuit diagram extract) (HRC1000 tip from SABA)
• Colours change or change often and are smeary. (HRC1000 tip from SABA)
• Line transformer is always destroyed at switch on from standby. (picture attached)
• HT high. (+ extract of circuit diagram)
• Goes into standby at switch on and switch off after 5 secs. If TV started with RC, the latter switches on and functions correctly. Occasionally goes out during operation. (with circuit diagram extract)
• Picture flickers and has colour tinge.
• No picture in Channel Plus. Audio OK. (extract of circuit diagram attached) (HRC1000 tips)
• Flashing video signal. Fields 2" displaced at top. (part of circuit diagram displayed)
• Fuse burnt.
• Part no. info: PSU repair kit.
• Poor vertical linearity.
• Switches to protection mode. at start-up. (part of circuit diagram displayed)
• PSU and line output stage switch on for a short time, then switches to standby.
• IF01, DF16, DF17 and DF18 blocked. TL19 also blocked.
• Crackling audio.
• High voltage sparking. (+ extract of circuit diagram)
• Video output stage IC (TEA5101A) on CRT board is defective.
• Poor grey scale.
• Vertical deflection IC IF01(TDA8178FS) fails repeatedly after replacement.
• Starts up with shrunken picture in the raster and foldover at the top of the page. (picture attached)
• Part no. info: PSU repair kit. (service info for SABA -HRC1000)
• High text brightness with shifted text. (extract of circuit diagram attached)
• Sound hums (Intercarrier hum) , AFC is incorrect.
• Excessive green. Bright picture. (part of circuit diagram displayed)
• Vertical foldover at top. (part of circuit diagram displayed)
• RC part number.
• Noise in audio. in standby. (with circuit diagram extract)
• Sound errors during picture alternation. (extract of circuit diagram attached)
• Intermittently dead. (part of circuit diagram displayed)
• Pulsates, flickers and fizzles. (+ extract of circuit diagram) (service info for SABA -HRC1000)
• Spare part no. info: Power supply repair kit.
• Clicks with Nicam. (extract of circuit diagram attached)
• Only snow on screen. Impossible to exit channel 02. (picture attached)
• No RC functions. Loud audio. Volume uncontrollable. Erratic functions. intermittently. (extract of circuit diagram attached)
• Picture shifted vertically. (picture attached)
• After a few mins picture fades and looses horizontal and vertical sync, then disappears completely.
• Vertical output IC (TDA8178FS) blown.
• Part no. info: PSU repair kit.
• Poor picture. via SCART. (part of circuit diagram displayed)
• Only pulsates once and high voltage also builds up.
• A spot is appearing when switching appliance off. (picture attached)
• Black vertical lines rises and falls. (+ extract of circuit diagram)
• Horizontal stripe. (with circuit diagram extract)
• No signal. Snowy raster. (HRC1000 SABA repair tip)
• Part no. info: PSU repair kit.
• Blows fuse. intermittently. (extract of circuit diagram attached)
• Slightly nasal sound and lower in TF1 reception, channel 29. Sound OK on other channels and via scart. (HRC1000 tip from SABA)
• Shuts down. after a few minutes.
• Horizontal tearing. (+ extract of circuit diagram)
• Faulty TXT.
• Improvement of the reliability of TL19. (extract of circuit diagram attached)
• Picture is lopsided on top, slightly too narrow. (with circuit diagram extract)
• Blue screen. (part of circuit diagram displayed)
• Part no. info: PSU repair kit. (HRC1000 SABA repair tip)
• Flyback lines and colour faults.
• Black and white picture in video via VCR. (part of circuit diagram displayed)
• Part no. info: PSU repair kit.
• No picture. Audio OK .
• Flyback lines. (extract of circuit diagram attached)
• Part no. info: PSU repair kit.
• Tuner fault. Functions correctly via scart.
• EHT comes in then switches off immediately. (extract of circuit diagram attached)
• Part no. info: PSU repair kit.
• No picture. via tuner. OK via SCART . (with circuit diagram extract)
• Improvement of line blanking. (picture attached) (HRC1000 SABA repair tip)
• Picture and sound missing in UHF. Snow on the screen. Ok in VHF. (extract of circuit diagram attached)
• RC part number.
• No start-up from standby. LED remains lit approx 3-4 seconds, then goes dark.
• Exiting the production mode.
• Popping Nicam. (extract of circuit diagram attached)
• How to display USER MENU with COMGENIUS RC.
• Letters PI are displayed in red on the left in the middle of the picture. No RC function, front controls function ok.
• Poor reception. (HRC1000 tip from SABA)
• Picture rolls. (picture attached)
• Switches off by itself. after a few seconds. (part of circuit diagram displayed)
• OSD has moved to the right and is far too big. (with circuit diagram extract)
• No colour. (+ extract of circuit diagram)
• Stretched picture. Picture shifted to the right. (+ extract of circuit diagram)
• Thin, black, wavy lines in picture.
• Picture distortion, resembles gull wings. (with circuit diagram extract)
• Colour varies. after warm-up. (with circuit diagram extract)
• Dead. LED is red .
• Flickering at top. Luminance and chroma flashes ON/OFF. (with circuit diagram extract)
• Picture shifted vertically. Flashing picture. (picture attached)
• Switches channels itself. (picture attached)
• Snow in picture. (with circuit diagram extract)
• Horizontal size varies. Vertical size varies. (HRC1000 SABA repair tip)
• Part no. info: PSU repair kit.
• Service mode menu.
• Line transformer and PSU transistor fail at the same time. Runs for several days after replacing both transistors.
• No sound in TV reception. Sound OK via scart.
• Whistling in sound when warm. (HRC1000 tips)
• Picture size changes, then ragged vertical lines appear especially in left picture area. lines are strongly visible by bright picture content. Raster ok by dark picture content.
• No picture. (with circuit diagram extract)
• Squealing noise. at start-up. (with circuit diagram extract)
• No picture via VHF tuner.
• Poor focus. when cold. (picture attached)
• Part no. info: PSU repair kit.
• CRT
• How to switch off protective circuit. (part of circuit diagram displayed)
• Poor picture with predominant colour. (extract of circuit diagram attached)
• Power supply circuit.
• Line tearing. when cold. Horizontal stripes.
• No TXT. (picture attached)
• Flyback lines. at top. (+ extract of circuit diagram)
• No picture. on upper half screen. (extract of circuit diagram attached)
• Dead. (part of circuit diagram displayed)
• No vertical scanning. White line in form of a "bow tie" very compressed in middle of screen. (HRC1000 tip from SABA)
• Horizontal lines. (part of circuit diagram displayed)
• Poor or popping Nicam. (picture attached)
• Video circuit production changes.
• Sond distorted at stereo. Stereo switches poorly. (picture attached)
• No blue.
• Shuts down. after start-up. LED is red . (+ extract of circuit diagram) (HRC1000 tips)
• Jagged vertical lines in picture when cold. AV mode ok.
• Part no. info: PSU repair kit.
• No tuner output.
• The following components are faulty: IC TDA8178, fuse resistor (24V), TL17 and TDA8178. (extract of circuit diagram attached)
• No E/W correction. (picture attached)
• Volume/picture stuck, cannot be altered or sound goes down. (HRC1000 tip from SABA)
• No start-up. LED is red .
• Stuck in standby. (extract of circuit diagram attached)
• Noise in audio. at low volume. (picture attached)
• Picture has vertically reduced by approx 5cm. Occasionally it slightly increases but with horizontal lines. Vertical instability at random. (+ extract of circuit diagram)
• Video mechanism faulty.
• Weak colours.
• Switches off by itself. after start-up. (extract of circuit diagram attached)
• Moire effect in the colour areas. (part of circuit diagram displayed)
• Dead. Buzzing from PSU. Standby LED does not light. (picture attached)
• Part no. info: PSU repair kit.
• No vertical deflection. Horizontal line in top quarter of picture. (HRC1000 SABA repair tip)
• No E/W correction. Excessive horizontal size. (+ extract of circuit diagram)
• Dark picture. intermittently. No colour. intermittently. (extract of circuit diagram attached) (HRC1000 tip from SABA)
• Picture is pinched in to approx. 5cm at the top. (SABA - HRC1000 information)
• TXT picture displayed to right hand side and excessive brightness. (extract of circuit diagram attached)
• Brightness varies. Colour varies.
• When switching back goes into standby and a chirping noise from loudspeakers. (service info for SABA -HRC1000)
• No picture. OSD OK .
• Field cramp at centre of picture. (picture attached)
• Flickering picture. at top. (+ extract of circuit diagram)
• Teletext bright and shifted to bottom of screen. (+ extract of circuit diagram)
• Sound interferences, intercarrier hum at picture change. (part of circuit diagram displayed) (service info for SABA -HRC1000)
• Demo Mode (available with version ICC8-B33).
• Unsuccessful N/S pincushion adjustments. (with circuit diagram extract)
• Appliance functions in standby, switches on briefly (LED green) then switches off immediately. (part of circuit diagram displayed)
• Horizontal jagged edge. (extract of circuit diagram attached)
• Volume alters by itself or sound is distorted. (part of circuit diagram displayed)
• PSU switches off after building up high voltage. (part of circuit diagram displayed)
• White screen. at start-up. Shuts down. (+ extract of circuit diagram)
• Low audio. Distorted audio. (picture attached)
• No sound. Field collapse.
• Red or green picture.
• Volume changes automatically, stays on max. and can not be adjusted any more.
• Slow start-up. Shuts down. at start-up. LED is red . (picture attached)
• Picture width changes when adjusting contrast (beam current dependent). (picture attached)
• HV builds up briefly and then switches off. Protective circuit responds.
• No picture. OK via SCART . (part of circuit diagram displayed)
• At start up standby diode lights up then goes off immediately. (+ extract of circuit diagram)
• Randomly enters SAFETY mode within 2 mins or 1 hour. Does not restart. (with circuit diagram extract)
• HV transistor fails repeatedly after start-up.
• TV blows with noise. (picture attached)
• No E/W equalisation. E/W phase and amplitude controls do not respond. (picture attached)
• Part no. info: PSU repair kit.
• No blue. intermittently.
• Tuning drifts.
• Enable child lock.
• RC no. info: RC.
• Distorted picture.
• Picture trembles. White flash turns green, red or blue. Impossible to adjust G2. Dark screen or picture in negative. (with circuit diagram extract)
• Black lines at lower part of screen.
• E/W fault. (part of circuit diagram displayed)
• No audio. No picture. (+ extract of circuit diagram)
• TP29 blows. (part of circuit diagram displayed)
• Barrel effect in N/S, picture is narrowed vertically towards the middle. (extract of circuit diagram attached)
• Picture is vertically too big. Horizontal amplitude is reduced. One colour is missing and there are flyback lines in picture.
• No contrast. (+ extract of circuit diagram)
• Line tearing (intermittently). (with circuit diagram extract)
• Stuck on a channel. Snowy raster. (picture attached)
• Clicks with Nicam. (extract of circuit diagram attached)
• After switching on, switches off again. At first LED lights up red then green. (part of circuit diagram displayed)
• Colour cast over the picture but varies as the TV warms up. (+ extract of circuit diagram)
• Vertical repair kit.
• No start up of line transformer. Standby light somes on for one sec then cuts out. No 8V on pin 40 of TA8659. 0V on pin 20 of uP IR01. (part of circuit diagram displayed)
• Red or occasionally yellow cast on picture. Colours saturation may also occur.
• Switches off by itself. after a few minutes. (part of circuit diagram displayed)
• Starts up, HV is present for a few secs, then appliance switches off and PSU switches to protective circuit
• Dim blue picture.
• No audio. only on certain channels.
• At switch off goes into black and white and spot on screen. (extract of circuit diagram attached)
• RC part number.
• No sound through tuner, via scart OK.
• RC part number.
• Protective circuit switches on switched on via RC. Happens intermittently when switched on via mains switch.
• Contents of power supply service kit. (part of circuit diagram displayed) (HRC1000 tip from SABA)
• Channel raster has shifted by two or more channels. (with circuit diagram extract) (SABA - HRC1000 information)
• No colour in Canal Plus. (with circuit diagram extract)
• Red picture.
• Wrong character in TXT, at switch over pages not readable.
• Fails completely, if it is switched on via the RCU and will not switch on again via the RCU.
• After operating for 10 mins, picture turns green then normal again. Random green coloration. (part of circuit diagram displayed)
• No sound. Horizontal lines on the screen. (+ extract of circuit diagram)
• Partial sound fault. Very low and poor sound on the little loudspeakers. No sound on boomer. (SABA - HRC1000 information)
• Adaptation to K' (K1) standard.
• Vertical red line across picture. (part of circuit diagram displayed)
• Video output stage IC (TEA5101A) on CRT board is defective. (picture attached)
• Vertical lines. in the centre.
• Three faint dark lines on right side of picture via AV input without a signal. (part of circuit diagram displayed)
• Bad sound when starting the TV. Gets better after a while.
• Red, green or blue missing
• Bars in picture. (with circuit diagram extract)
• Service information - Contrast and beam current adjustment after replacement of video/chroma module.
• Poor vertical linearity. at top. Vertical foldover. Flyback lines. (part of circuit diagram displayed) (HRC1000 tip from SABA)
• Part no. info: PSU repair kit.
• Part no. info: PSU repair kit.
• Occasionally memorized data of control unit processor is lost at switch on or switch off with mains switch.
• Switches on and then off again. LED changes from red to green. (part of circuit diagram displayed) (HRC1000 tips)
• Trips (after a few minutes). (+ extract of circuit diagram)
• Trips (after a few seconds). (extract of circuit diagram attached)
• Reduced vertical deflection.
• Dubbing on is too large/shifted to the right. (part of circuit diagram displayed) (HRC1000 SABA repair tip)
• Narrowed picture in the raster. Veiled and foldover on the top 15cm of the screen, giving rise to pictures the wrong way round.
• Blank raster. Flyback lines. No RC functions. (part of circuit diagram displayed)
• Power supply starts up with EHT and stops. (part of circuit diagram displayed)
• Streaky picture with line doubling effect. SCART OK.
• No HV. LED is red . (with circuit diagram extract)
• Brief squealing after switch on and no function. Red standby lamp is lit.
• Horizontal line. in the centre. (with circuit diagram extract)
• Low noise from power supply at start up with power switch, then dead (no standby).
• Moire effect in UHF.
• Shuts down. after start-up. (with circuit diagram extract)
• Information about field output chip replacements. (with circuit diagram extract)
• No N/ S correction.
• Nasal sound with French channels. CCIR and scart sound OK. (part of circuit diagram displayed)
• Colour bleeding. (picture attached)
• Reduced vertical size. Vertical foldover. (part of circuit diagram displayed)
• At switch on, light is on, EHT present then everything stops, no light or secondary power supply. (picture attached)
• Stripes in picture when adjusting upper vertical part. Then turns off. (with circuit diagram extract)
• Excessive vertical size. (part of circuit diagram displayed)
• RC part number.
• Slow start-up. Switches to standby.
• No command signal on the line BU base. (with circuit diagram extract)
• Only one colour in picture (e.g. red).
• No colour.
• Protective mode comes into operation when line output stage is working. (part of circuit diagram displayed)
• HT starts up for 1sec., then switches off.
• Does not start up. On pin 16 of the mains IC there is only approx 9V.
• No reception. (picture attached)
• How to set normal level. (HRC1000 tips)
• Power supply and line output stage start up for a short time, finally appliance goes into stand-by. (picture attached)
• Part no. info: PSU repair kit.
• Erratic functions. Cycles on/off. intermittently.
• Spare part no. info: Power supply repair kit.
• No blue.
• No picture. Red LED comes on, then green. High voltage builds up for a short time only then no LED indication. (+ extract of circuit diagram)
• No sound from loudspeaker.
• Jagged vertical lines via tuner. OK via SCART.
• Power supply problem: in standby slight pulsating noise, when on operation ok, in standby TV ok but standby light goes off and does not start up again. To start up mains must be switched off. (part of circuit diagram displayed)
• Dark screen. Poor picture. (extract of circuit diagram attached)
• Flyback lines. Blue flooded picture. (extract of circuit diagram attached)
• Appliance has no HF reception. Snowy picture. (picture attached)
• Receives no HF signals. Band change is not possible. (+ extract of circuit diagram)
• Part no. info: PSU repair kit. (HRC1000 tip from SABA)
• No start-up from standby. Buzzing from PSU. (part of circuit diagram displayed)
• LG08 has blown or becomes very hot. (part of circuit diagram displayed) (HRC1000 SABA repair tip)
• Erratic audio at start-up. Noise and crackling audio via both channels. Gets better if left on longer.
• Shuts down. after a few seconds. (service info for SABA -HRC1000)
• No picture. after a few seconds. Switches to protection mode. (part of circuit diagram displayed)
• Distorted verticals and occasionally no frame sync according to picture. Picture ok when going via scart on another appliance. (part of circuit diagram displayed)
• PSU repair set 35029300.
• Too wide picture, E/W fault, appliance does not react to change of horizontal amplitude, as well as E/W adjustment.
• Menu oversized and left side has shifted downwards. (picture attached)
• Vertical collapse. (+ extract of circuit diagram)
• No colour. intermittently. Bars in picture. (picture attached)
• PSU function test.
• Vertical foldover at bottom.
• Reduced horizontal size. Switches off by itself. (picture attached)
• No vertical deflection. White horizontal line is slightly curved. (with circuit diagram extract)
• Part no. info: processors.
• No picture (intermittently). (picture attached)
• No tele dialog display with front control or remote control. (picture attached)
• Intermittent image rolling through, vertical sync jitters and at program switch intermittently two programes are overjumped. (picture attached)
• Enter service mode.
• No functions. Does not switch to standby. (picture attached)
• Noise in audio. after warm-up.
• Torn picture. at top. (HRC1000 tips)
• No sound or scratching on some channels (when cold). (SABA - HRC1000 information)
• Loss of one colour. Varying greyscale.
• Erratic red, green, or blue picture. Colour saturation varies. Convergence slightly defective.
• No correction on the top and bottom of the screen. (SABA - HRC1000 information)
• No tuning. (with circuit diagram extract)
• No picture. Coloured raster present with shadows.
• Occasionally white flash on the screen, mainly in quick search video on a cassette.
• No audio.
• Dark picture. Flyback lines. (part of circuit diagram displayed)
• Black horizontal streak in TXT mode. (extract of circuit diagram attached)
• Comes on for a short time. (extract of circuit diagram attached)
• Erratic start-up. Stuck in standby. possibly intermittent.
• Tripping. (part of circuit diagram displayed) (SABA - HRC1000 information)
• Poor sound after a while, then sound drops out.
• Line tearing.
• Blank raster. No OSD. Audio OK . (extract of circuit diagram attached)
• RC part number.
• Low picture brightness at switch on. Nothing is visible unless brightness and contrast are at maximum. (extract of circuit diagram attached)
• When you switch off the TV using the remote control the red light comes on then 4 secs after goes off. It is then impossible to switch on the TV again with the remote control.
• Signal coming and goind. Colour flashes on and off.
• Noise in audio. No audio. at start-up. Poor audio. after a while.
• Part no. info: PSU repair kit.
• Negative picture.
• After approx 2 hours of operation, volume is on full level and can not be decreased, via RC either.
• The top of the picture is flickering which looks like a field jitter. Luma and chroma are flashing on/off. (picture attached) (HRC1000 tips)
• Impossible to switch on again via the RC after going into standby. (part of circuit diagram displayed)
• No start-up. (picture attached) (HRC1000 SABA repair tip)
• No RF reception. Picture OK via scart.
• HT hissing at switch on, then appliance switches off. (extract of circuit diagram attached)
• No green in picture or TXT.
• Standby LED flashes every second. (picture attached)
• No audio. (picture attached)
• Green picture when cold. As appliance warms up, also the other colours appear. Slightly blurred picture.
• Bright picture. in TXT. Picture shifted to the right. in TXT. (+ extract of circuit diagram)
• Faulty raster.
• Part no. info: PSU repair kit. (service info for SABA -HRC1000)
• Red picture. Distorted picture. after warm-up. (with circuit diagram extract)
• Part no. info: PSU repair kit.
• Picture appears then flyback line and screen turns white. Sound OK. (part of circuit diagram displayed)
• UL1 90V, RL25 heats up and TL19 fails. (+ extract of circuit diagram)
• Too much red, green and blue via TEA5101A.
• Unable to adjust picture symmetry.
• No blue. Low contrast.
• Short popping noise at start-up, then no function.
• After turning on TL19 (S20AF) is destroyed immediately. (picture attached)
• Crackling audio. (HRC1000 tips)
• Contents of Thomson frame output stage repair kit.
• Fuse FP01 blows. (picture attached)
• Green lines are flashing on the screen. (+ extract of circuit diagram)
• Flashing green lines. (extract of circuit diagram attached)
• PSU does not oscillate. (with circuit diagram extract)
• Low contrast. (+ extract of circuit diagram)
• TXT does not display all colours and blue lines/ stripes jitter in the picture. (HRC1000 tip from SABA)
• Line output transistor fails repeatedly. (+ extract of circuit diagram)
• Vertical line. (+ extract of circuit diagram)
• No red.
• Line tearing. Flickering picture.
• RC part number.
• Linearity fault. Too high image amplitude. E/W equalisation not adjustable. (+ extract of circuit diagram)
• Part number info: power supply repair
• Switches immediately to protective circuit when switched on via RC. (+ extract of circuit diagram)
• Sound is distorted by STEREO, partly by mono also.
• Poor focus. Interference in picture. (part of circuit diagram displayed)
• Cuts out when standby selected. No red LED. (+ extract of circuit diagram)
• Remains in standby and goes into safety mode. Remove RV02, CV02 does not change anything. DP50 unsoldered, remains in standby, 300V, BU powered. (with circuit diagram extract)
• Functions correctly then cuts our intermittently and goes dead 2-5 times a day. Impossible to restart by switch. (picture attached)
• Flash of colour in Secam. (with circuit diagram extract)
• Part no. info: PSU repair kit.
• When switched on picture turns red but you can make out the individuals. (with circuit diagram extract)
• No vertical deflection. Horizontal line. in the centre. Reduced horizontal size. (picture attached)
• Starts up, EHT audible then goes into standby. (part of circuit diagram displayed)
• No picture at all both when monitoring the channels and when playing back a cassette. After approx. 1hr dots and lines are seen appearing then picture is correct. (part of circuit diagram displayed)
• Vertical jitter. Picture rolls. (+ extract of circuit diagram)
• Field output IC TDA8178/F replacement - supply kit info.
• IC IG01 (TDA4950) is destroyed at start-up.
• On start-up short beep is audible and then appliance switches off.
• On Canal Plus, intermittent black stripes that lead to the decoder switching off. (part of circuit diagram displayed)
• Sound distorted and quiet shortly after switch on, then OK.
• PSU cuts out after going into standby. (with circuit diagram extract)
• Poor audio. Noise in audio.
• Strong colours. Flyback lines. (picture attached)
• No sound or picture. The EHT and other supplies are present, just a volume at minimum on-screen display was present.
• Vertical collapse. Standby LED lit . (part of circuit diagram displayed)
• Does not switch on. Only a beep at start-up.
• Black vertical lines on picture. (with circuit diagram extract)
• Colour fault. (with circuit diagram extract)
• Picture has disappeared (sound and screen display ok). The same via scart followed by raster fault then CTV then dead. Standby light power supply flashes with noise in the power supply. (part of circuit diagram displayed)
• RP62 burns. (with circuit diagram extract)
• TL19 always breaks down after start-up. (+ extract of circuit diagram)
• RF noise. AV picture OK. On search does not find anything. (picture attached)