HTM14117 / SABA [TV (Standard)]

• No synchronisation. when changing channels (after warm-up). (HTM14117 tips)
• No picture. via SCART. (+ extract of circuit diagram)
• Moire effect. (+ extract of circuit diagram)
• Excessive horizontal size. (picture attached)
• Dark picture. Audio OK .
• Only hum from speaker.
• No RGB drive.
• Horizontal lines. at top.
• Slow start-up. (extract of circuit diagram attached)
• Replacing IC IS001. (with circuit diagram extract)
• Picture trembles. (with circuit diagram extract)
• No vertical deflection. White line. in the centre. (picture attached)
• Horizontal linearity fault.
• "NO SIGNAL" is displayed on blue background. (part of circuit diagram displayed)
• USYS voltage incorrect.
• How to install channels.
• No start-up.
• Reset PIN code.
• No picture. intermittently. Audio OK .
• No channels. Blue screen.
• No picture. OSD OK .
• Disable child lock.
• Picture drops out, screen becomes dark. Picture appears after a while followed by noise in loudspeakers. Error occurs after warm-up. (part of circuit diagram displayed)
• Displays 'PIN'.
• Erratic start-up. PSU pulsates. (part of circuit diagram displayed)
• No audio. No picture. (+ extract of circuit diagram)
• Stuck in standby. (with circuit diagram extract)
• Whistling.
• Dead. (part of circuit diagram displayed)
• Spots and glimmers on screen with random shapes and colours when TV switched off by RC or by On/Off button. (with circuit diagram extract)
• Blows chopper transistor. (service info for SABA -HTM14117)
• Tuner audio present in AV mode.
• Spare part info: transistor TP020. (picture attached)
• Power problem. (extract of circuit diagram attached)
• No picture on half of the frame, only raster is present. The other half of frame is black. (with circuit diagram extract)
• Load operating noise from PSU, particularly with dark picture scenes. (picture attached)
• Yellow "P" displayed constantly on picture. (HTM14117 tips)
• Shuts down after start-up. Picture appears briefly after switch-on.
• TP020 blows in primary PSU. (HTM14117 tip from SABA)
• No green.
• Switches to protection mode. (extract of circuit diagram attached)
• Hissing noise from speakers with aerial connected. No RC functions. User controls OK. Audio OK via SCART.
• Replacement of IC IV001. (picture attached)
• Horizontal line. (HTM14117 tips)
• Hissing sound via SCART socket. OK with aerial cable.
• Noise in picture. Streaks in picture.
• White noise in AV mode.
• Does not go to Service Mode. (part of circuit diagram displayed)
• Does not start after stopping with the On/off button. (part of circuit diagram displayed)
• No tuning. (part of circuit diagram displayed)
• Starts up three times then switches off. (picture attached)
• With 12V/24V supply, appliance drops out occasionnally if supply voltage is below 14V under load (picture and sound).
• Horizontal foldover. on the right. (HTM14117 tips)
• No picture. after warm-up.
• Loud noise via AV even when volme is turned down.
• No functions. (with circuit diagram extract)
• Enter service mode. (HTM14117 SABA repair tip)
• IF circuit does not work. (+ extract of circuit diagram) (HTM14117 tip from SABA)
• Excessive red. when cold. (part of circuit diagram displayed)
• Purity fault. (extract of circuit diagram attached)
• Switches to standby after 30 secs in operation and then starts again.
• Maximum volume at start-up. If MUTE button is pressed then volume turns to minimum and increases to maximum by itself.
• Intermittently dead.
• Poor picture then no picture and flyback lines on grey screen. (part of circuit diagram displayed)
• No colour on certain channels, which are visible only in B/W. (SABA - HTM14117 information)
• No colour at PB of playstations or camera/video in PAL. (+ extract of circuit diagram)
• Background noise or HF hiss after HF program switch over. (extract of circuit diagram attached)
• Hintergrund Geräusch oder HF Rauschen nach HF Programm Umschaltung.
• No start-up from standby with RC. LED lit. .
• Channels enter AV mode when using front controls or Pr(+)/Pr(-) keys.
• Changes channels and volume by itself.
• Poor linearity. at bottom. (extract of circuit diagram attached)
• TV requires PIN.
• No horizontal deflection. after start-up. (with circuit diagram extract)
• Curtain effect. (with circuit diagram extract)
• Horizontal interferences in middle of screen, particularly evident on normal picture. (picture attached)
• PSU test. (part of circuit diagram displayed) (HTM14117 tip from SABA)
• No picture. Audio OK . (part of circuit diagram displayed)
• Loud buzz on AV input.
• No start-up. (extract of circuit diagram attached)
• No picture and sound in HF. Channels run through continuously. Shows "SIGNAL= 0" and screen is blue. Picture and sound are OK via scart.
• Loud buzz on AV input. (picture attached) (HTM14117 tips)
• Dark picture. OSD OK .
• Video mutes occasionally. Blue screen and no signal on screen. (picture attached)
• Switches itself channels. Audio volume in increased to maximum. (picture attached)
• No start-up. LED blinks .
• No raster.
• Starts up at the wrong time from standby. (+ extract of circuit diagram)