HTM20117 / SABA [TV (Standard)]

• Does not go to Service Mode. (with circuit diagram extract)
• Hissing noise from speakers with aerial connected. No RC functions. User controls OK. Audio OK via SCART.
• No start-up. LED blinks .
• Picture drops out, screen becomes dark. Picture appears after a while followed by noise in loudspeakers. Error occurs after warm-up. (+ extract of circuit diagram)
• Curtain effect. (part of circuit diagram displayed)
• Starts up at the wrong time from standby. (part of circuit diagram displayed)
• Excessive horizontal size. (+ extract of circuit diagram)
• Changes channels and volume by itself. (HTM20117 tips)
• No colour at PB of playstations or camera/video in PAL. (with circuit diagram extract)
• Dead. (with circuit diagram extract)
• Background noise or HF hiss after HF program switch over. (+ extract of circuit diagram) (HTM20117 SABA repair tip)
• No start-up.
• No green.
• Poor linearity. at bottom. (part of circuit diagram displayed)
• No picture. OSD OK .
• Spare part info: transistor TP020. (picture attached)
• Horizontal interferences in middle of screen, particularly evident on normal picture. (picture attached)
• With 12V/24V supply, appliance drops out occasionnally if supply voltage is below 14V under load (picture and sound). (service info for SABA -HTM20117)
• Blows chopper transistor.
• Switches to protection mode. (with circuit diagram extract) (HTM20117 tips)
• TV requires PIN.
• IF circuit does not work. (extract of circuit diagram attached)
• No start-up from standby with RC. LED lit. .
• Loud buzz on AV input. (extract of circuit diagram attached)
• Maximum volume at start-up. If MUTE button is pressed then volume turns to minimum and increases to maximum by itself.
• No picture. intermittently. Audio OK .
• Loud buzz on AV input.
• No vertical deflection. White line. in the centre. (extract of circuit diagram attached)
• Power problem. (picture attached)
• Channels enter AV mode when using front controls or Pr(+)/Pr(-) keys. (service info for SABA -HTM20117)
• No horizontal deflection. after start-up. (part of circuit diagram displayed)
• Excessive red. when cold. (picture attached)
• No colour on certain channels, which are visible only in B/W.
• No synchronisation. when changing channels (after warm-up).
• No picture and sound in HF. Channels run through continuously. Shows "SIGNAL= 0" and screen is blue. Picture and sound are OK via scart.
• No raster.
• Tuner audio present in AV mode.
• Replacing IC IS001. (+ extract of circuit diagram)
• Spots and glimmers on screen with random shapes and colours when TV switched off by RC or by On/Off button. (picture attached)
• PSU test. (part of circuit diagram displayed) (SABA - HTM20117 information)
• Reset PIN code.
• Does not start after stopping with the On/off button. (with circuit diagram extract) (HTM20117 SABA repair tip)
• Starts up three times then switches off. (extract of circuit diagram attached)
• No start-up. (picture attached) (SABA - HTM20117 information)
• Horizontal lines. at top.
• Shuts down after start-up. Picture appears briefly after switch-on. (HTM20117 tips)
• No picture. after warm-up.
• Horizontal foldover. on the right.
• "NO SIGNAL" is displayed on blue background. (extract of circuit diagram attached)
• Enter service mode. (service info for SABA -HTM20117)
• Load operating noise from PSU, particularly with dark picture scenes. (extract of circuit diagram attached)
• Noise in picture. Streaks in picture.
• Hintergrund Geräusch oder HF Rauschen nach HF Programm Umschaltung.
• TP020 blows in primary PSU.
• USYS voltage incorrect.
• White noise in AV mode.
• Loud noise via AV even when volme is turned down.
• Switches to standby after 30 secs in operation and then starts again.
• Whistling.
• Displays 'PIN'.
• Intermittently dead.
• Dark picture. Audio OK .
• Horizontal linearity fault.
• Stuck in standby. (extract of circuit diagram attached)
• Purity fault. (+ extract of circuit diagram)
• Replacement of IC IV001. (extract of circuit diagram attached)
• Disable child lock.
• Moire effect. (part of circuit diagram displayed)
• Video mutes occasionally. Blue screen and no signal on screen. (part of circuit diagram displayed) (SABA - HTM20117 information)
• No tuning. (extract of circuit diagram attached)
• No channels. Blue screen.
• Erratic start-up. PSU pulsates. (+ extract of circuit diagram)
• No picture. via SCART. (part of circuit diagram displayed)
• Slow start-up. (with circuit diagram extract)
• No audio. No picture. (picture attached)
• How to install channels.
• No RGB drive.
• Only hum from speaker.
• Dark picture. OSD OK .
• Switches itself channels. Audio volume in increased to maximum. (+ extract of circuit diagram)
• No functions. (picture attached)
• Picture trembles. (picture attached)
• Hissing sound via SCART socket. OK with aerial cable.
• Yellow "P" displayed constantly on picture. (HTM20117 SABA repair tip)
• No picture on half of the frame, only raster is present. The other half of frame is black. (part of circuit diagram displayed)
• Poor picture then no picture and flyback lines on grey screen. (with circuit diagram extract) (service info for SABA -HTM20117)
• Horizontal line. (HTM20117 tip from SABA)
• No picture. Audio OK . (extract of circuit diagram attached)