ICC11 / SABA [TV (chassis)]

• No sound via AV1 and AV2 when cold. Sound ok via HF. (service info for SABA -ICC11)
• Too much green.
• Switching off deflection protective circuit. (picture attached)
• Standby LED lights red, then orange and then becomes red again. Then LED flashes 3 times red.
• Switches to standby. after a while. (+ extract of circuit diagram) (ICC11 tip from SABA)
• Pink "P" in picture
• E-W error. Switches off after a while and then after approx. 10 secs switches on again. (picture attached)
• Vertical lines are jagged in the top third.
• Synchro error.
• Poor geometry.
• Red LED flashes 3 times, then once green. No picture, no sound.
• Volume control. (ICC11 tips)
• RC part number.
• Main and standby PSU switch on and off
• No picture. TXT and menu display OK. (+ extract of circuit diagram)
• Part no. info.: RC.
• No SAT reception. SAT tuner is not recognized in the menu. Only grey screen via SCART and terrestrial tuner.
• Switches to protection mode. at start-up.
• Enable child lock. (service info for SABA -ICC11)
• Insufficient system voltage and cannot be adjusted
• Dark screen. OSD OK . (extract of circuit diagram attached)
• Dark picture. (ICC11 tips)
• Loud crackel from loudspeaker during switch on
• Part no info: RC.
• Loud crackle in loudspeaker during switch on
• Only black-white picture via AV1 on connected DVD-Player, via digital FTA-receiver coloured, overdriven, red picture. Via AV2 both function perfectly. Signalform at scart socket cannot be adjusted via volume +/-.
• No blue. (+ extract of circuit diagram)
• Strange clicking in rhythmical intervals via loudspeaker. Noise disappears when muted and diappears nearly when set to normal or mono.
• No start-up. (+ extract of circuit diagram) (ICC11 SABA repair tip)
• Colour fault or only two colours (even in TXT)
• No start-up from standby. intermittently.
• Coloured line or only two colours on picture (also with TXT).
• RC part number.
• Loud crackling in loudspeaker at switch on.
• Brightness varies. Switches to protection mode. (with circuit diagram extract)
• Stripe in lower third of picture in zoom operation. (+ extract of circuit diagram)
• Coloured line or only two colours on picture (also with TXT).
• Switches off by itself. after a few minutes. LED blinks . (+ extract of circuit diagram)
• Loud crackle in loudspeaker at switch on.
• Loud sizzling in loudspeakers at switch on.
• Service info: PSU test with incandescent lamp.
• Strong whistling from loud-speakers at switch on.
• Part no info: RC.
• No picture. OSD OK . (picture attached) (ICC11 tip from SABA)
• No vertical deflection. (+ extract of circuit diagram)
• Switches to protection mode. possibly intermittent.
• Switches off sporadically , blinks 4x4, switches on again. This repeats itself for approx. 20 min., then works stable. (SABA - ICC11 information)
• Shuts down. after a few seconds. LED blinks . (+ extract of circuit diagram)
• Strong whistling from loud-speakers at switch on.
• Dies, menu is intermittently displayed. Knocksensitive.
• Vertical foldover at top.
• Horizontal stripes. intermittently. (part of circuit diagram displayed)
• System voltage is too low. Unable to adjust to nominal value. (extract of circuit diagram attached)
• Bar in picture intermittently. Random characters in picture. (part of circuit diagram displayed) (service info for SABA -ICC11)
• Service info: PSU test with incandescent lamp.
• Loud cracking at start-up.
• No control via user control or RC. Dark screen. Standby LED remains orange. (extract of circuit diagram attached)
• Picture is compressed at the top approx 10cm. (extract of circuit diagram attached)
• Service info: PSU test with light bulb
• Compressed picture and foldover in picture part. (+ extract of circuit diagram)
• RC part number.
• Coloured line or only two colours on picture (also with TXT).
• If switching fast (zapping) with SAT receiver connected , switches to sn Standby. Appliance pulsates 4 times and comes back. (+ extract of circuit diagram)
• RC part number.
• Coloured line or only two colours on picture (also with TXT). (ICC11 tip from SABA)
• Language adjustment.
• No picture. No sound. No TXT. OSD and AV OK.
• Starts up briefly, then error message 4/4. Symptom is repeated periodically. (+ extract of circuit diagram)
• No picture. in E-E. OSD and TXT OK . (SABA - ICC11 information)
• Approx. 5cm wide, dark stripes in upper picture part when cold.
• Loud cracking from loudspeaker at start-up.
• Loud crackle in loudspeaker at switch on.
• Coloured line or only two colours on picture (also with TXT).
• U/Syst runs out of control. (extract of circuit diagram attached)
• Picture distorted and shifted. RC has no functions. (with circuit diagram extract)
• Slow start-up. when cold. (picture attached)
• RC part number.
• Service info: PSU test with incandescent lamp.
• Y-signal is missing.
• RC part number.
• No picture. No sound. Starts up and LED switches to yellow. (part of circuit diagram displayed)
• Switches off. LED flashes 4 x1x4. (extract of circuit diagram attached)
• Loud crackle from loudspeaker during switch on
• Exiting the production mode.
• Error code 4 / 4 is displayed (ICC11 tips)
• Switches to protection mode (intermittently). (picture attached)
• How to bridge electronic fuse. (picture attached)
• Loud crackling in loudspeaker at switch on.
• No audio. Other functions OK . (SABA - ICC11 information)
• Bright picture with flyback lines, which do not disappear when G2 is decreased.
• No synchronisation. OSD OK .
• Useful information in case of lamp test. (part of circuit diagram displayed)
• Black line on the picture intermittently. Odd marks on the picture.
• Line in bottom third of the picture during zoom (with circuit diagram extract)
• Brightness varies.
• Whistling from PSU. (picture attached)
• Beat in loudspeakers.
• Switching problems in 4:3. Impossible to activate field correction.
• Line switches on for a short time, then error code 4. (ICC11 tips)
• Linearity error at upper picture edge.
• No start-up. LED is red .
• Geometry or rotation with 16x9 picture tubes cannot be adjusted. (extract of circuit diagram attached)
• How to switch off protective circuit. (extract of circuit diagram attached)
• Oscillations in vertical lines.
• Service information: Error code 4.
• No audio. No picture.
• Service info: PSU test with a lamp
• Switches off. Red LED begins to flash 4 times. 3 sec Pause. Then flashes again 4 times and appliance starts again. (extract of circuit diagram attached)
• Intermittently black picture display (similar to TXT) and occasionally no display when adjusting volume etc. Occurs approx every two weeks (extract of circuit diagram attached)
• Vertical foldover at top and bottom. (with circuit diagram extract)
• Loud cracking in loudspeaker at start-up.
• Dead. (+ extract of circuit diagram)
• Dead. Orange LED blinks slowly.
• No red. (+ extract of circuit diagram)
• Vertical deflection fault, slightly rolled up at top, horizontal white line in upper third of picture. (with circuit diagram extract)
• Service info: PSU test with incandescent lamp.
• Coloured line or only two colours on picture (also with TXT).
• Switches off when beam current changes. (part of circuit diagram displayed)
• Switches briefly to standby after half an hour, and blinks 4 times.
• Vertical edges of the picture are serrated.
• Upper picture part is compressed. (picture attached)
• Slow start-up. (extract of circuit diagram attached)
• Error codes. (extract of circuit diagram attached)
• Blurred characters on OSD via AV on digital satellite channels.
• Switches to protection mode (LED blinks). (+ extract of circuit diagram)
• Coloured line or only two colours on picture (also with TXT).
• HV builds up briefly (beeps), then decreases and error code 4 is displayed.
• Service info: PSU test with light bulb.
• Picture shifted to the right. No RC functions. E/W fault. (picture attached)
• No audio (intermittently). (part of circuit diagram displayed)
• Locked in PAL mode and when operating menu.
• Poor luminance. (with circuit diagram extract)
• Cycles on/off. (+ extract of circuit diagram)
• Remains in standby at switch on. Front LED is flashing. EHT attempts to start up for 1/4 of a sec (green LED). Smell of burning. (with circuit diagram extract) (ICC11 tips)
• Service info: PSU test with incandescent lamp.
• Turns off. Flashes 4 times (red/orange). Turns on again.
• Coloured line or only two colours on picture (also with TXT).
• Excessive horizontal size.
• No RC functions. Other functions OK . (with circuit diagram extract)
• Changes over programs individually.
• Picture is doubled. (SABA - ICC11 information)
• Enter service mode.
• Switches program sites to and fro, intermittently also in basic menu.
• Bright picture with one colour. Then switches off. (part of circuit diagram displayed)
• Loud crackle in loudspeaker at switch on.
• No function. HV builds up briefly, then swithces off again. Standby LED flashes 4x red.
• Loud crackle in loudspeaker at switch on. (ICC11 tip from SABA)
• TP020 is S/C.
• RC part number.
• Standby PSU does not function. (picture attached)
• Loud crack in loudspeaker at switch on.
• Loud crackle in loudspeaker at switch on.
• Activating the install menu.
• Switches to standby at beam curennt changes, e.g. switching from TXT to program or also when plugging in and out of antenna. Turns on again after approx. 20-30 sec. LED flashes until restarting.
• Dead. Standby LED flashes . (+ extract of circuit diagram)
• E/W fault. (picture attached)
• Coloured line or only two colours on picture (also with TXT).
• No green. (picture attached)
• Coloured line on picture or only 2 colours (even in TXT).
• RC part number.
• Flyback frame. Green picture.
• Focus problems.
• RC part number.
• Coloured line or only two colours on picture (also with TXT).
• Lamp test. PSU check (32kHz switching PSU) with light bulb.
• Switches to protection mode. when cold.
• Intermittently no audio. Intermittently no RC. P appears in picture down in left.
• Switches to protection. PSU pumps 3 times. (picture attached)
• Colour fault or only two colours (also in TXT).
• Strong whistling from loud-speakers at switch on.
• RC part number.
• No picture. LED flashes four times three, then flashes constantly. (with circuit diagram extract)
• Service info : PSU test with lamp
• No start up voltage for the standby PSU. (extract of circuit diagram attached)
• Dark picture. LED is orange. .
• Does not react to U8 RC.
• Intermittently no start-up. LED switches from red to yellow.
• Two black horizontal bars in upper picture area, especially by white picture content, via AV and tuner. Black OSD background at the bottom.
• Dead. Red LED blinks.
• No picture. on upper half screen.
• Loud crack in loudspeaker at start-up.
• No start-up (intermittently).
• Reduced vertical size at top. (part of circuit diagram displayed)
• Switches off after some time. LED flashes 4x and appliance starts up again. Fault occurs in irregular time intervals.
• RC part number.
• No audio. intermittently. No picture. intermittently. (SABA - ICC11 information)
• Negative picture. (part of circuit diagram displayed)
• Picture has colour fault or only two colours (also in TXT).
• Loud crackle in loudspeaker at switch on.
• Colourfault or only two colours (even in TXT)
• No start-up. when cold. Standby LED flashes . (picture attached)
• Severe red tinge with flyback lines after start up. Safety switch off to standby after a few seconds.
• Contrast automatic fault. If someone is standing in front of the appliance, picture becomes brighter and then darker again.
• Service info: PSU test with a lamp
• Coloured line or only two colours on picture (also with TXT).
• Line transistor TL004 (ON4914) has S/C. (with circuit diagram extract)
• IF002 becomes defective. (part of circuit diagram displayed)
• No horizontal synchronisation.
• Picture folds at the top or the bottom immediately or after some time (heat fault). (picture attached) (SABA - ICC11 information)
• Picture too big. Distorted picture. (+ extract of circuit diagram)
• Picture is too wide, can be adjusted, to a certain degree, in the service mode.
• Disable electronic combination lock.
• Fine, blue flyback lines, in particular duriging dark passages. Low contrast picture.
• No RC functions. Picture too small. (+ extract of circuit diagram)
• Coloured line or only two colours on picture (also with TXT).
• RC part number.
• Coloured line or only two colours on picture (also with TXT).
• No RC reception. "PI" is displayed on screen. (+ extract of circuit diagram) (ICC11 tip from SABA)
• Programming menu is blocked and PIN code is unknown.
• Coloured line or only two colours on picture (also with TXT). (service info for SABA -ICC11)
• Coloured line or one colour is missing. Also in TXT mode.
• Service info: PSU-test with incandescent lamp.
• Picture faint. No contrast. Brightness, colour and contrast can be adjusted. Looks like Y-signal is missing. (picture attached)
• Intermittently standby PSU does not start up
• Service info: PSU test with lamp
• Switches to protective circuit during operation, makes 2 starting attempts, then continues running. (extract of circuit diagram attached)
• Service information: PSU test with a lamp. (ICC11 tip from SABA)
• Service info: PSU test with incandescent lamp.
• Loud cracking in loudspeakers at start-up.
• PSU test with light bulb.
• Service info: PSU test with incandescent lamp.