EURAS System
    EURAS worldwideeuras.com    
EURAS System

ICC19100HZ ICC19 / SABA [TV (Standard) (chassis)]

The EURAS repair tip database for professional technicians and service engineers supplies the following faults for ICC19100HZ / SABA.

List of fault symptoms:
  • Switches to protection mode. possibly intermittent (after warm-up).
  • No channel storing.
  • Displays error code "52" (does not recognize DVT module).
  • Protection mode activated. (service info for SABA -ICC19100HZ)
  • No colours on most of the channels. Auto channel search does not find all channels and completes slowly.
  • Vertical collapse in the vertical drive IV001 (STV2162) when tapping.
  • Error codes. (picture attached)
  • Cannot be switched on intermittently from standby, LED goes out. If appliance is switched to standby from full operation, LED goes out intermittently. After disconnecting from mains, LED is on again.
  • Line tearing and picture height twitches approx 5mm. (part of circuit diagram displayed)
  • No functions. PSU pulsates.
  • No functions (intermittently). (extract of circuit diagram attached)
  • Does not react to width and geometry adjustments.
  • No installation menu (locked).
  • Slow start-up. when cold. (+ extract of circuit diagram)
  • Digital display in the picture, intermittently horizontal string of pearl like lines in the right half of the picture.
  • Dead. (extract of circuit diagram attached)
  • Enter service mode.
  • Switches intermittently off. Red LED flashes constantly. (with circuit diagram extract)
  • No start-up. intermittently. LED is red .
  • TV picture and OSD display have blue tint and colour blue is smeared when modulated to the right. TXT OK.
  • No start-up. possibly intermittent. (SABA - ICC19100HZ information)
  • No start-up. when cold.
  • Ticks three times and then blinks constantly.
  • Three start-up attempts, then LED flashes. Switches off.
  • Starts briefly three times, then LED blinks (part of circuit diagram displayed)
  • Red picture.
  • Switches off. Red LED flashes constantly (part of circuit diagram displayed)
  • Transistor TL030 fails immediately after replacement.
  • No start-up. (with circuit diagram extract)
  • Switches to protection mode. after a few minutes.
  • Dark picture.
  • Poor vertical synchronisation. when cold.
  • Appliance pulsates three times and switches to standby. (with circuit diagram extract)
  • Switches to protection mode. LED blinks .
  • No start-up. LED blinks .
  • At switch-on with mains switch appliance attempts to start up 3-4 times with a squeak. After that, no function. LED is not alight.
  • No HV. (extract of circuit diagram attached)
  • No button operation. after a few minutes.
  • High voltage increases briefly, then switches off. Red LED flashes constantly. (part of circuit diagram displayed)
  • Bright picture with flyback lines, switches off. (with circuit diagram extract)
  • Excessive horizontal size. Switches to protection mode (intermittently).
  • How to set up programme.
  • Brightness and sound fails.Sound via scart OK. (part of circuit diagram displayed)
  • Starts intermittently three times and then switches to standby, LED blinks red constantly. (part of circuit diagram displayed)
  • Red LED lights constantly. (picture attached)
  • Power supply tries to start up 3 times, then red LED flashes and no function. (extract of circuit diagram attached) (service info for SABA -ICC19100HZ)
  • Low brightness.
  • Shows the last 5 error codes during operation. Error code which occurred the last, stays on first place.
  • Horizontal, green lines. Text is OK. (ICC19100HZ tip from SABA)
  • Starts up three times then switches off. LED blinks .

When SABA ICC19100HZ fails , these symptoms are known and EURAS knows the remedy/solution.

Tips are coming from EURAS customers, workshops and payed technicians from all over the world. SABA ICC19100HZ fails can be better solved.

If SABA ICC19100HZ fails, this information will help you. Here you can only see the symptom list, to access remedies, you must register.

With help of this list a solution is found often when SABA ICC19100HZ fails.


Additionally to repairtips or service information ICC19100HZ ICC19 is linked to 20 components (IC's and/or transformers) in the Tectra database, through which you can identify electrical compatibilities (crossreferences) in appliances.


For ICC19100HZ ICC19 there are 6 compatible appliances known and can be listed.


In the repair discussion pinboard for ICC19100HZ ICC19 there are 15 replies to questions asked about 5 different repair problems.
With access to EURAS you can all read them or enter your own questions and get help for ICC19100HZ from EURAS technicians or other users.

You can display a list with all appliances that have build in the ICC19100HZ/SABA chassis.

Do you want to see this remedies/cures for repairtips?   Register here for the EURAS System
Please note: access to the EURAS System can be granted only to professional household electronics repair shops/technicians/TV/Video which are authorized for service by a manufacturer, or can prove to be professionally certified to do repairs on electronic appliances. You will be asked for a statement and information accordingly during registration.

If you do not qualify as stated above and you have an appliance that needs technical service, we do recommend you to contact the manufacturer (for example through his website) or go to a professional household/Video/TV electronics repair shop close to you.

Already registered? open ICC19100HZ SABA in EURAS

All details on the EURAS System: English | Deutsch | Français | Italiano | Español | Magyarul | Português | Polski | Română | Greek |


Back to EURAS Homepage >> All manufacturers >> SABA tech tips  











Last updated: 05. Nov 2009 14:15:28 MET, doccode ISO9002AS168EKA200805C [cachelite] EURASMOP

Responsible for the content: EURAS International GmbH, Eime, Germany.
All brand- or productnames are copyrighted by the respective manufacturer of the appliance and are only being used for identification purposes.