CBP215200 / SANYO [TV 55 (51) cm picture]

• No audio.
• Switches to standby at start-up. Intermittenly may come on, but then switches to standby.
• No tuning. No display.
• Macro problem.
• Horizontal width confirmation.
• These models can be converted into a remote set from a non remote set.
• Tuner AFT adjustment.
• Drive VR adjustment.
• Colour phase adjustment.
• Stuck in standby (intermittently).
• Faint lines in background of picture which only shows on dark scenes. Can look like text noise.
• Blank screen for one minute, screen all white for 30 secs then picture flares severely as if tube defective.
• Stuck in standby.
• Picture is missing, no response using RCU or front controls.
• No start-up from standby. (SANYO - CBP215200 information)
• No colour (intermittently).
• Red picture. No green. No blue.
• No audio.
• Downward line on last character of each word on TXT.
• Reduced frame scan with blank raster or frame collapse.
• No start-up (after a few minutes). Power LED lit . (CBP215200 SANYO repair tip)
• Intermittent darkening on screen. Sound OK.
• -10 countdown appears on screen with a good signal present. (CBP215200 SANYO repair tip)
• Horizontal oscillation adjustment.
• AGC adjustment.
• Modifications to circuit.
• Dead. No RC functions.
• Vertical size adjustment.
• No OSD.
• Blank screen. Switches off after 15 min.
• Intermittent or permanent RF noise on screen with varying brightness. No graphics and/or no sound. (CBP215200 SANYO repair tip)
• No picture. Audio OK . (service info for SANYO -CBP215200)
• Blue drive is lost and occasional green band on picture.
• Intermittently dead.
• Intermittent loss of colour especially at switch on or channel change.
• Horizontal centre adjustment.
• Intermittently stuck in standby. Random switch over. Interference or picture shift in screen.
• Vertical size adjustment.
• Does not come out of standby. If link 'JST' is made, set displays last no. selected and the ten min countdown.
• Partial field collapse, no sound, shaky picture.
• Switches to standby.
• On last character of each word on teletext, there is a downward line.
• Picture frays and is too narrow.
• No picture. intermittently. Audio OK .
• IC701 locks up. (SANYO - CBP215200 information)
• Bright white screen with flyback lines. (CBP215200 SANYO repair tip)
• Comes on for a short time.
• CW oscillator adjustment.
• Picture appears snowy, no functions possible.
• Computer controlled teletext frequency adjustment. (CBP215200 tip from SANYO)
• No manual control operation.
• No colour.
• No picture. OSD OK .
• Vertical collapse.
• Vertical centre adjustment.
• No complete standby.
• Switches to standby. after a few seconds. (CBP215200 tips)
• 1H delay adjustment.
• Stuck in aux. mode
• No memory.
• Teletext page number is missing.
• +B power supply adjustment.
• OSG size and position is incorrect.
• No RC functions. (SANYO - CBP215200 information)
• Change to circuit. (CBP215200 tip from SANYO)
• Focus adjustment.
• Does not change channels.
• Switches to standby after 5 secs. If ON/OFF switch held in, steps through channels with good picture. (CBP215200 tip from SANYO)
• Screen VR adjustment.
• Sometimes the set fails to come out of standby, it also suffers from disturbance on the picture and random channel changing.
• Loss of green on screen graphics.
• Character setting adjustment.
• Will not tune but graphic's bars are OK.
• Bias VR adjustment.
• HV confirmation.