CBP2865 / SANYO [TV]

• White point adjustment.
• Ringing in verticals, also associated with colour phase, instability and ringing from flyback transformer.
• Screen VR adjustment.
• Horizontal width confirmation.
• When TXT selected, does not switch to TXT but then TV does not change channel.
• Intermittent white raster with low height.
• 1H delay adjustment. (CBP2865 tips)
• After switching on the appliance goes into stand by. (CBP2865 SANYO repair tip)
• No function after start up.
• Frame collapse followed by standby mode.
• Intermittently trips. Blank raster. No field sync. (service info for SANYO -CBP2865)
• Dead or cuts out.
• White balance adjustment.
• No picture or sound. Intermittent fault which sometimes disappears by itself.
• Blank raster (intermittently).
• Colour phase adjustment.
• Sub-contrast adjustment.
• Focus adjustment.
• After switch on goes into standby.
• When TXT selected TV does not switch to TXT but then TV does not change channel.
• Black lines at bottom of screen.
• Switches to standby.
• Does not stop on auto search. (CBP2865 tip from SANYO)
• Bright raster and reduced height intermittently.
• Sub-contrast adjustment.
• Bell filter adjustment.
• Horizontal centre adjustment. (SANYO - CBP2865 information)
• Looks like an identification fault.
• SECAM identification discriminator adjustment.
• B-Y adjustment.
• Buzz on sound at min volume, also present in mute mode.
• Focus adjustment.
• Intermittently picture and sound disappear leaving bright white raster or insufficient height.
• 1H delay adjustment.
• Bell filter adjustment.
• If pincushion correction PCB is replaced, new PCB may fail.
• Lower half of frame severely stretched.
• Side pincushion correction adjustment. (CBP2865 SANYO repair tip)
• Vertical centre and width adjustment.
• Trips (intermittently).
• Does not stop on auto search.
• CW oscillator adjustment.
• Colour phase adjustment.
• No function after switch on. (SANYO - CBP2865 information)
• Sub-brightness adjustment.
• Computer controlled teletext frequency adjustment.
• Sub-brightness adjustment.
• After switch on no function.
• HV confirmation. (CBP2865 tip from SANYO)
• Vertical centre and width adjustment.
• Lower half of frame severely stretched.
• AGC adjustment.
• Screen VR adjustment.
• When pincushion correction PCB is replaced a burn up can sometimes occur on new PCB.
• Video OUT adjustment. (CBP2865 tip from SANYO)
• Computer controlled teletext frequency adjustment.
• Side pincushion correction adjustment.
• CW oscillator adjustment.
• Frame pairing at the bottom of the picture. (CBP2865 SANYO repair tip)
• After set is warm sound goes completely. Picture disappears leaves blank blue raster only (channel change works).
• Intermittently sound becomes distorted with field collapse and just a blue screen. (CBP2865 tip from SANYO)
• Horizontal width confirmation.
• Intermittent field roll.
• Sub colour adjustment.
• FM output adjustment.
• Horizontal oscillation adjustment.
• Intermittently goes to standby leaving channel number on which after a few seconds changes to av.
• Horizontal oscillation adjustment. (SANYO - CBP2865 information)
• Intermittently sound and picture would disappear leaving a bright white raster with reduced height, almost as soon as the fault occurred, the set would return to normal.
• FM output adjustment.
• B-Y adjustment. (CBP2865 SANYO repair tip)
• Video OUT adjustment.
• Green tint to picture.
• EHT comes up for a few seconds then set cuts out.
• Intermittent picture and sound.
• Horizontal centre adjustment.
• HV confirmation.
• SECAM identification discriminator adjustment.
• Black lines across screen followed by picture fade out to magenta screen then height reduced and loss of tuning.
• Blank raster. No field sync. Intermittently trips. (CBP2865 tip from SANYO)
• Sub colour adjustment.
• AGC adjustment.
• Reduced horizontal size.