CBP2866 / SANYO [TV]

• When pincushion correction PCB is replaced a burn up can sometimes occur on new PCB.
• No function after switch on.
• Dead or cuts out. (CBP2866 tips)
• Ringing in verticals, also associated with colour phase, instability and ringing from flyback transformer.
• Too much green in the picture.
• FM output adjustment.
• Horizontal oscillation adjustment.
• SECAM identification discriminator adjustment. (CBP2866 SANYO repair tip)
• HV confirmation.
• Screen VR adjustment. (CBP2866 SANYO repair tip)
• CW oscillator adjustment. (CBP2866 tips)
• EHT comes up for a few seconds then set cuts out.
• Video OUT adjustment.
• Horizontal width confirmation.
• Blank raster (intermittently).
• Lower half of frame severely stretched.
• Horizontal oscillation adjustment.
• 1H delay adjustment.
• Intermittently sound and picture would disappear leaving a bright white raster with reduced height, almost as soon as the fault occurred, the set would return to normal.
• Blank raster. No field sync. Intermittently trips.
• SECAM identification discriminator adjustment.
• When TXT selected TV does not switch to TXT but then TV does not change channel.
• Trips (intermittently).
• HV confirmation. (service info for SANYO -CBP2866)
• Intermittent field roll.
• FM output adjustment.
• Colour phase adjustment.
• Black lines across screen followed by picture fade out to magenta screen then height reduced and loss of tuning.
• Reduced horizontal size.
• White point adjustment.
• No picture or sound. Intermittent fault which sometimes disappears by itself.
• Sub-brightness adjustment.
• Colour phase adjustment.
• Lower half of frame severely stretched.
• Buzz on sound at min volume, also present in mute mode.
• Screen VR adjustment.
• If pincushion correction PCB is replaced, new PCB may fail. (CBP2866 SANYO repair tip)
• White balance adjustment.
• Computer controlled teletext frequency adjustment.
• AGC adjustment. (service info for SANYO -CBP2866)
• 1H delay adjustment.
• Intermittent white raster with low height.
• Bright raster and reduced height intermittently.
• Switches to standby.
• Intermittently sound becomes distorted with field collapse and just a blue screen.
• Computer controlled teletext frequency adjustment.
• If the appliance is warmed up the sound and the picture content disappears and only leaves behind a blue raster. Channel change works.
• After switch on goes into standby.
• CW oscillator adjustment.
• Horizontal centre adjustment.
• After switching on the appliance goes into stand by.
• Black lines at bottom of screen. (CBP2866 SANYO repair tip)
• Green tint to picture.
• Sub colour adjustment.
• Frame pairing at the bottom of the picture.
• Horizontal width confirmation.
• Looks like an identification fault.
• Video OUT adjustment.
• Focus adjustment.
• Intermittently goes to standby leaving channel number on which after a few seconds changes to av.
• After set is warm sound goes completely. Picture disappears leaves blank blue raster only (channel change works).
• Focus adjustment.
• Intermittently trips. Blank raster. No field sync.
• Frame collapse followed by standby mode.
• Sub-contrast adjustment.
• After switch on no function.
• B-Y adjustment. (service info for SANYO -CBP2866)
• Side pincushion correction adjustment.
• Sub colour adjustment.
• No function after start up.
• AGC adjustment.
• Intermittently sound becomes distorted with field collapse and just a blue screen.
• B-Y adjustment.
• Vertical centre and width adjustment.
• Vertical centre and width adjustment.
• When TXT selected, does not switch to TXT but then TV does not change channel.
• Sub-contrast adjustment.
• Side pincushion correction adjustment.
• Horizontal centre adjustment.
• Sub-brightness adjustment.
• Intermittent picture and sound.
• Bell filter adjustment.
• Bell filter adjustment.
• Does not stop on auto search.