EURAS System
    EURAS worldwideeuras.com    
EURAS System

CEP2876D00 / SANYO [TV 70-74 (66-70) cm picture]

The EURAS repair tip database for professional technicians and service engineers supplies the following faults for CEP2876D00 / SANYO.

List of fault symptoms:
  • No picture, no sound, just snow when tuning selected.
  • Pincushion distortion. 5cm field collapse on each screen edges.
  • No E/W correction.
  • No raster.
  • Unstable picture. Difficulty in tuning. OK with scart.
  • No HT or tube heaters.
  • Collapses to a thin bowed horizontal line.
  • No picture. Audio OK . (service info for SANYO -CEP2876D00)
  • Switching FET (BUZ90A) defective.
  • R653 continues to fail.
  • Vertical collapse. (SANYO - CEP2876D00 information)
  • PSU switching transistor fails at start-up.
  • Mains fuse blown.
  • Attempts to start up, but does not succeed and switches to standby.
  • Snow in E-E.
  • Stuck in standby.
  • Shuts down (intermittently). (CEP2876D00 tip from SANYO)
  • Corrupted data.
  • No horizontal or vertical deflection.
  • Reduced vertical size. (CEP2876D00 tip from SANYO)
  • Only three volume levels (zero-middle-maximum).
  • A few colour lines on top of picture.
  • Excessive horizontal size. Pincushion distortion.
  • No start up after being turned off for several hours. It eventually starts up when attempting to switch on several times.
  • SERVICE mode:
  • Enter service mode.
  • Fast hiccup when connecting TV. LED flashes.
  • No function. No red LED.
  • White streaks.
  • Clock flashing O S G text clock OK.
  • No picture, just snow when tuning selected. No sound
  • No start up. Fast tripping.
  • E/W fault. intermittently.
  • No luminance signal. In TXT only page no. is visible.
  • Lines in picture. at top. (CEP2876D00 tip from SANYO)
  • Dead.
  • Doesn't function even if standby LED lights up. When pressing mains switch, attempts to start up but goes to standby.
  • No picture. No sound. Rattles.
  • White screen. Flyback lines. (SANYO - CEP2876D00 information)
  • Red, green and blue flyback lines. (CEP2876D00 tip from SANYO)
  • Excessive brightness. Audio OK .
  • Flyback lines. at top.
  • No audio.
  • Vertical folover at bottom and insufficient height. Approx 20cm stripe on centre of screen.
  • No function. Standby LED OFF. Pressing Standby, cracking from PTC.
  • Switches to standby. Squealing noise. (CEP2876D00 tip from SANYO)
  • How to call up SERVICE mode.
  • Blank raster, sound OK. OK if used with Scart input from VCR.
  • Q600 blown up.
  • Unable to switch out of standby when cold.
  • No picture.
  • Starts up, functions for a minute and immediately disconnects, remaining in standby.
  • No vertical deflection.
  • Very dark and greyish picture. (service info for SANYO -CEP2876D00)
  • Bright raster. Audio OK .
  • E/W fault.
  • No vertical sync. In TXT only page no. visible.
  • Transistor Q650 (BU508A) is S/C.
  • Tuning drifts.
  • Slow response to channel change, takes 20-30 secs to change. (SANYO - CEP2876D00 information)

With help of this list a solution is found often when SANYO CEP2876D00 fails.


Additionally to repairtips or service information CEP2876D00 is linked to 26 components (IC's and/or transformers) in the Tectra database, through which you can identify electrical compatibilities (crossreferences) in appliances.


Chassis information is available (which chassis is built in into CEP2876D00 ).

EURAS system also knows 23 appliances having the same chassis as CEP2876D00 and can easily list them.

For CEP2876D00 there are 5 compatible appliances known and can be listed.


In the repair discussion pinboard for CEP2876D00 there are 5 replies to questions asked about 7 different repair problems.
With access to EURAS you can all read them or enter your own questions and get help for CEP2876D00 from EURAS technicians or other users.

Do you want to see this remedies/cures for repairtips?   Register here for the EURAS System
Please note: access to the EURAS System can be granted only to professional Video/household electronics repair shops/TV/technicians which are authorized for service by a manufacturer, or can prove to be professionally certified to do repairs on electronic appliances. You will be asked for a statement and information accordingly during registration.

If you do not qualify as stated above and you have an appliance that needs technical service, we do recommend you to contact the manufacturer (for example through his website) or go to a professional TV/household/Video electronics repair shop close to you.

Already registered? open CEP2876D00 SANYO in EURAS

All details on the EURAS System: English | Deutsch | Français | Italiano | Español | Magyarul | Português | Polski | Română | Greek |


Back to EURAS Homepage >> All manufacturers >> SANYO tech tips  











Last updated: 01. Dec 2008 23:44:19 MET, doccode ISO9002AS168EKA200805C EURASMOP

Responsible for the content: EURAS International GmbH, Eime, Germany.
All brand- or productnames are copyrighted by the respective manufacturer of the appliance and are only being used for identification purposes.