EURAS System
    EURAS worldwideeuras.com    
EURAS System

CEP2884 / SANYO [TV]

The EURAS repair tip database for professional technicians and service engineers supplies the following faults for CEP2884 / SANYO.

List of fault symptoms:
  • No picture. Audio OK .
  • A few colour lines on top of picture.
  • SERVICE mode:
  • Reduced vertical size.
  • Mains fuse blown.
  • Starts up, functions for a minute and immediately disconnects, remaining in standby.
  • R653 continues to fail.
  • No vertical deflection.
  • No audio. (service info for SANYO -CEP2884)
  • No luminance signal. In TXT only page no. is visible.
  • PSU switching transistor fails at start-up.
  • Unstable picture. Difficulty in tuning. OK with scart.
  • Collapses to a thin bowed horizontal line.
  • Slow response to channel change, takes 20-30 secs to change.
  • Vertical collapse.
  • E/W fault. intermittently.
  • How to call up SERVICE mode.
  • Clock flashing O S G text clock OK.
  • No start up after being turned off for several hours. It eventually starts up when attempting to switch on several times.
  • No function. Standby LED OFF. Pressing Standby, cracking from PTC.
  • Q600 blown up.
  • No picture, just snow when tuning selected. No sound
  • No vertical sync. In TXT only page no. visible.
  • Excessive horizontal size. Pincushion distortion. (CEP2884 SANYO repair tip)
  • Excessive brightness. Audio OK .
  • No picture. No sound. Rattles.
  • No function. No red LED.
  • Fast hiccup when connecting TV. LED flashes.
  • Lines in picture. at top.
  • Unable to switch out of standby when cold.
  • Blank raster, sound OK. OK if used with Scart input from VCR.
  • E/W fault.
  • Snow in E-E.
  • Flyback lines. at top.
  • No picture.
  • Very dark and greyish picture.
  • No horizontal or vertical deflection.
  • Shuts down (intermittently). (service info for SANYO -CEP2884)
  • Pincushion distortion. 5cm field collapse on each screen edges.
  • Vertical folover at bottom and insufficient height. Approx 20cm stripe on centre of screen.
  • Transistor Q650 (BU508A) is S/C.
  • Switching FET (BUZ90A) defective.
  • No picture, no sound, just snow when tuning selected.
  • Doesn't function even if standby LED lights up. When pressing mains switch, attempts to start up but goes to standby. (SANYO - CEP2884 information)
  • No raster.
  • Attempts to start up, but does not succeed and switches to standby.
  • No start up. Fast tripping. (CEP2884 tips)
  • White streaks. (SANYO - CEP2884 information)
  • Red, green and blue flyback lines.
  • Bright raster. Audio OK .
  • Enter service mode.
  • No E/W correction.
  • Corrupted data.
  • Dead.
  • White screen. Flyback lines.
  • No HT or tube heaters.
  • Tuning drifts.
  • Switches to standby. Squealing noise.
  • Stuck in standby. (CEP2884 tip from SANYO)

With this service information, you may repair SANYO CEP2884 faster/better when it fails.

When SANYO CEP2884 fails , these symptoms are known and EURAS knows the remedy/solution.

Tips are coming from EURAS customers, workshops and payed technicians from all over the world. SANYO CEP2884 fails can be better solved.

If SANYO CEP2884 fails, this information will help you. Here you can only see the symptom list, to access remedies, you must register.

With help of this list a solution is found often when SANYO CEP2884 fails.


Additionally to repairtips or service information CEP2884 is linked to 26 components (IC's and/or transformers) in the Tectra database, through which you can identify electrical compatibilities (crossreferences) in appliances.


Chassis information is available (which chassis is built in into CEP2884 ).

EURAS system also knows 23 appliances having the same chassis as CEP2884 and can easily list them.

In the repair discussion pinboard for CEP2884 there are 5 replies to questions asked about 7 different repair problems.
With access to EURAS you can all read them or enter your own questions and get help for CEP2884 from EURAS technicians or other users.

Do you want to see this remedies/cures for repairtips?   Register here for the EURAS System
Please note: access to the EURAS System can be granted only to professional technicians/TV/Video/household electronics repair shops which are authorized for service by a manufacturer, or can prove to be professionally certified to do repairs on electronic appliances. You will be asked for a statement and information accordingly during registration.

If you do not qualify as stated above and you have an appliance that needs technical service, we do recommend you to contact the manufacturer (for example through his website) or go to a professional TV/Video/household electronics repair shop close to you.

Already registered? open CEP2884 SANYO in EURAS

All details on the EURAS System: English | Deutsch | Français | Italiano | Español | Magyarul | Português | Polski | Română | Greek |


Back to EURAS Homepage >> All manufacturers >> SANYO tech tips  











Last updated: 01. Dec 2008 16:53:51 MET, doccode ISO9002AS168EKA200805C EURASMOP

Responsible for the content: EURAS International GmbH, Eime, Germany.
All brand- or productnames are copyrighted by the respective manufacturer of the appliance and are only being used for identification purposes.