EURAS System
    EURAS worldwideeuras.com    
EURAS System

CEP2896 / SANYO [TV]

The EURAS repair tip database for professional technicians and service engineers supplies the following faults for CEP2896 / SANYO.

List of fault symptoms:
  • Dead.
  • No vertical sync. In TXT only page no. visible.
  • No start up after being turned off for several hours. It eventually starts up when attempting to switch on several times.
  • R653 continues to fail.
  • Switches to standby. Squealing noise. (CEP2896 tip from SANYO)
  • Doesn't function even if standby LED lights up. When pressing mains switch, attempts to start up but goes to standby.
  • Flyback lines. at top.
  • Unstable picture. Difficulty in tuning. OK with scart.
  • No E/W correction.
  • Snow in E-E.
  • Clock flashing O S G text clock OK. (CEP2896 SANYO repair tip)
  • Bright raster. Audio OK .
  • Very dark and greyish picture.
  • Vertical collapse.
  • No HT or tube heaters.
  • No vertical deflection.
  • Slow response to channel change, takes 20-30 secs to change.
  • Pincushion distortion. 5cm field collapse on each screen edges.
  • PSU switching transistor fails at start-up.
  • Reduced vertical size.
  • Collapses to a thin bowed horizontal line. (CEP2896 SANYO repair tip)
  • Starts up, functions for a minute and immediately disconnects, remaining in standby.
  • Transistor Q650 (BU508A) is S/C. (CEP2896 tip from SANYO)
  • How to call up SERVICE mode.
  • Blank raster, sound OK. OK if used with Scart input from VCR.
  • No luminance signal. In TXT only page no. is visible.
  • Switching FET (BUZ90A) defective.
  • Tuning drifts.
  • Corrupted data. (service info for SANYO -CEP2896)
  • No function. Standby LED OFF. Pressing Standby, cracking from PTC.
  • Excessive horizontal size. Pincushion distortion.
  • Fast hiccup when connecting TV. LED flashes.
  • Attempts to start up, but does not succeed and switches to standby.
  • Enter service mode. (CEP2896 SANYO repair tip)
  • Shuts down (intermittently).
  • No picture, just snow when tuning selected. No sound
  • No picture.
  • Unable to switch out of standby when cold.
  • Q600 blown up.
  • No audio.
  • A few colour lines on top of picture.
  • E/W fault.
  • Red, green and blue flyback lines.
  • No picture, no sound, just snow when tuning selected.
  • No picture. No sound. Rattles. (CEP2896 tip from SANYO)
  • Vertical folover at bottom and insufficient height. Approx 20cm stripe on centre of screen.
  • No horizontal or vertical deflection.
  • E/W fault. intermittently.
  • White streaks.
  • Mains fuse blown.
  • Lines in picture. at top.
  • White screen. Flyback lines.
  • SERVICE mode:
  • No function. No red LED.
  • No raster. (CEP2896 tip from SANYO)
  • No start up. Fast tripping.
  • No picture. Audio OK . (CEP2896 SANYO repair tip)
  • Excessive brightness. Audio OK . (SANYO - CEP2896 information)
  • Stuck in standby.

Tips are coming from EURAS customers, workshops and payed technicians from all over the world. SANYO CEP2896 fails can be better solved.

If SANYO CEP2896 fails, this information will help you. Here you can only see the symptom list, to access remedies, you must register.

With help of this list a solution is found often when SANYO CEP2896 fails.


Additionally to repairtips or service information CEP2896 is linked to 26 components (IC's and/or transformers) in the Tectra database, through which you can identify electrical compatibilities (crossreferences) in appliances.


Chassis information is available (which chassis is built in into CEP2896 ).

EURAS system also knows 23 appliances having the same chassis as CEP2896 and can easily list them.

In the repair discussion pinboard for CEP2896 there are 5 replies to questions asked about 7 different repair problems.
With access to EURAS you can all read them or enter your own questions and get help for CEP2896 from EURAS technicians or other users.

Do you want to see this remedies/cures for repairtips?   Register here for the EURAS System
Please note: access to the EURAS System can be granted only to professional TV/Video/household electronics repair shops/technicians which are authorized for service by a manufacturer, or can prove to be professionally certified to do repairs on electronic appliances. You will be asked for a statement and information accordingly during registration.

If you do not qualify as stated above and you have an appliance that needs technical service, we do recommend you to contact the manufacturer (for example through his website) or go to a professional household/TV/Video electronics repair shop close to you.

Already registered? open CEP2896 SANYO in EURAS

All details on the EURAS System: English | Deutsch | Français | Italiano | Español | Magyarul | Português | Polski | Română | Greek |


Back to EURAS Homepage >> All manufacturers >> SANYO tech tips  











Last updated: 01. Dec 2008 16:46:38 MET, doccode ISO9002AS168EKA200805C EURASMOP

Responsible for the content: EURAS International GmbH, Eime, Germany.
All brand- or productnames are copyrighted by the respective manufacturer of the appliance and are only being used for identification purposes.