EURAS System
    EURAS worldwideeuras.com    
EURAS System

CEP3014D00 / SANYO [TV]

The EURAS repair tip database for professional technicians and service engineers supplies the following faults for CEP3014D00 / SANYO.

List of fault symptoms:
  • Goes into standby after 5 seconds.
  • No audio. OK via SCART .
  • Dark picture. No colour.
  • Colour adjustment.
  • Intermittent picture blanking.
  • Sub-brightness adjustment.
  • Horizontal centre adjustment.
  • No picture. Stripes in picture.
  • No function, loud whistle sound.
  • No functions. (CEP3014D00 tip from SANYO)
  • One third from top of screen has severe field cramp.
  • Chopper transistor S/C all the time with start on.
  • No output from chopper power supply.
  • Variations in picture size according to level of picture luminance.
  • Ragged verticals.
  • HT high at approx 180V.
  • Power supply adjustment.
  • Starts up in standby, then goes back into standby.
  • Tripping.
  • Greyscale and tracking adjustment.
  • Focus adjustment.
  • Line output transistor fails repeatedly.
  • Picture reduced to 10cm in the centre of the screen.
  • White picture. Sometimes picture appears but only chroma.
  • Can not be switched on. LED flashes.
  • Video detector adjustment.
  • Excessive brightness. Flyback lines. (CEP3014D00 tips)
  • Distorted vertical linearity on top of screen.
  • Starts up correctly. Sound and picture present for 5 sec, then goes into standby. Green lines during the first seconds.
  • Line output transistor continuously fails.
  • Bright raster. Flyback lines.
  • Stuck in standby.
  • Vertical size adjustment.
  • Switches to standby. after a few seconds.
  • Vertical collapse.
  • HT voltage low and no regulation.
  • PSU doesn't start-up.
  • Starts up then stops after 5 sec.
  • No picture. Audio OK . (CEP3014D00 tips)
  • AGC adjustment.
  • No start-up from standby.
  • Line output transistor S/C.
  • Vertical foldover at bottom.
  • HV check.
  • Only vertical line.
  • Blank screen.
  • Slow start-up.
  • Line output transistor Q432 (2SD1649) continuously fails.
  • Purity adjustment.
  • Line transistor blows repeatedly.
  • Dead.
  • Tuning display width adjustment.

When SANYO CEP3014D00 fails , these symptoms are known and EURAS knows the remedy/solution.

Tips are coming from EURAS customers, workshops and payed technicians from all over the world. SANYO CEP3014D00 fails can be better solved.

If SANYO CEP3014D00 fails, this information will help you. Here you can only see the symptom list, to access remedies, you must register.

With help of this list a solution is found often when SANYO CEP3014D00 fails.


Additionally to repairtips or service information CEP3014D00 is linked to 8 components (IC's and/or transformers) in the Tectra database, through which you can identify electrical compatibilities (crossreferences) in appliances.


Chassis information is available (which chassis is built in into CEP3014D00 ).

EURAS system also knows 21 appliances having the same chassis as CEP3014D00 and can easily list them.

In the repair discussion pinboard for CEP3014D00 there are 3 replies to questions asked about 1 different repair problems.
With access to EURAS you can all read them or enter your own questions and get help for CEP3014D00 from EURAS technicians or other users.

Do you want to see this remedies/cures for repairtips?   Register here for the EURAS System
Please note: access to the EURAS System can be granted only to professional technicians/TV/household electronics repair shops/Video which are authorized for service by a manufacturer, or can prove to be professionally certified to do repairs on electronic appliances. You will be asked for a statement and information accordingly during registration.

If you do not qualify as stated above and you have an appliance that needs technical service, we do recommend you to contact the manufacturer (for example through his website) or go to a professional TV/household/Video electronics repair shop close to you.

Already registered? open CEP3014D00 SANYO in EURAS

All details on the EURAS System: English | Deutsch | Français | Italiano | Español | Magyarul | Português | Polski | Română | Greek |


Back to EURAS Homepage >> All manufacturers >> SANYO tech tips  











Last updated: 01. Dec 2008 16:52:27 MET, doccode ISO9002AS168EKA200805C EURASMOP

Responsible for the content: EURAS International GmbH, Eime, Germany.
All brand- or productnames are copyrighted by the respective manufacturer of the appliance and are only being used for identification purposes.