185702565 54390260 / SCHAUBLORENZ [TV (Standard)]

• No picture. Audio OK .
• Line output stage (S2000AF) fails.
• No picture. Vertical collapse.
• Attempts to start up, but remains in standby with two lines on display.
• Enter service mode.
• PSU does not oscillate.
• Knock sensitive.
• Double lines in the display. At switch on the display changes. Appliance does not function.
• Mechanical resonation from the cabinet on symmetric models.
• Colour loss on reception of local cable news channel (colour subcarrier frequency deviation).
• Only two lines in display. After start briefly number "1", then two lines visible again.
• No functions. 2 lines flash in display. SAT LED blinks.
• E/W pincushion distortion. Ballooning effect. No RC functions.
• Excessive horizontal size.
• No picture or sound. No demagnetising hum.
• Loud bang at switch on.
• E/W fault (intermittently).
• Picture resembles widescreen, subtitles out of picture range. Rest of picture is OK.
• Line foldover.
• PSU chirps and switches off in standby.
• Shuts down.
• Remains blocked on channel 4.
• Does not start up, remains in standby. When you press On, P1 is displayed, then goes to standby.
• IC (TDA8170) fails again after a short while.
• Picture shifted horizontally.
• Poor picture.
• E/W fault or insufficient picture width or picture width twitches sporadically with an E/W fault.
• Switches to standby after start-up with mains.
• OSD folds over and rolls from right to left.
• Does not find channels.
• Intermittently dead. (+ extract of circuit diagram)
• Standby LED and SAT LED flash in display.
• Negative picture. when cold.
• No start-up from standby. Only SAT LED flashes.
• Forced operation for PSU.
• Flashes, E/W variations i.e. unstable picture.
• At contrast change picture height comes apart.
• Brightness increases gradually. Canal Plus changes to black and white. (185702565 tip from SCHAUBLORENZ)
• Vertical foldover. Clicking noise.
• Picture is indented, approx 5 cm black bars on left/right.
• Remains in standby. When attempting to switch on SAT-R LED flashes.
• E/W fault. Knock sensitive.
• Green vertical streaks of ca. 15cm covering the whole screen.
• Picture width twitches in irregular intervals, mainly shortly after switch on.
• No start-up. Standby LED lit .
• Stuck in standby. LED blinks .
• VCR in EXT1: picture in B/W, in EXT2: coloured picture but horizontal jitter effect. Clicking noise from PSU when switching over with RC (zapping).
• E/W amplitude cannot be adjusted. Lines in picture.
• Intermittently no menu.
• A colour is missing eg. blue.
• Type of transistor T830. (with circuit diagram extract)
• Fuse, R703 and BUF405A blow at switch on.
• Switches on then off after a second.
• Line transformer blown.
• Dead. Shows 2 dashes when switched on. Flashing green LED when brought out of standby.
• Whistling flyback transformer. Brightness hardly visible over 20cm width in middle of picture tube.
• Value of R815. (extract of circuit diagram attached)
• No E/W correction. (SCHAUBLORENZ - 185702565 information)
• Switches to standby. intermittently.
• Picture becomes narrower as brightness and contrast increases. E/W fault. (SCHAUBLORENZ - 185702565 information)
• After warming up when switching over a SAT channel site occasionally the selected channel site does not appear but channel site 1.
• Picture jumps up and down about 1cm every 2 secs. Vertical size is reduced a little.
• Starts up, then switches immediately to standby. If P+ key is pressed, appliance attempts to start up again.
• No picture except for three lines (measuring lines) in top of picture (weak).
• No start-up. (+ extract of circuit diagram)
• HV arcing. (part of circuit diagram displayed)
• Dead or tripping.
• Black and white picture. No horizontal amplitude control.
• Picture menu cannot be adjusted.
• S2000 blows after 2 days.
• Picture switches to B/W with Canal Plus, then goes to standby. (SCHAUBLORENZ - 185702565 information)
• Flashover at base of line transformer.
• Attempts to start up, but turns off. Screen doesn't light up.
• No start-up. Red LED switches off. Chirping approx. 3 secs.
• Occasionally HT flashover at switch on.
• No colour in PB in CUE/REV mode.
• When switching on, PSU chirps.
• Dead.
• E/W fault. after a few minutes.
• No functions.
• At switch on appliance goes immediately again into standby. The lowermost LED (R SAT) flashes continuously: (error message "no vertical pulse")
• Reduced horizontal size. Horizontal foldover (after a while). No synchronisation.
• Occasionally appliance switches independently to another channel site.
• Red LED SAT flashes.
• The appliance occasionally cannot be switched on from stand by mode.
• Loud rustle in the PSU, in particular without aerial.
• Reduced horizontal size.
• Appliance does not start up at low temperatures. (185702565 SCHAUBLORENZ repair tip)
• No start-up. when cold. (SCHAUBLORENZ - 185702565 information)
• The appliance is locked in SAT position.
• T502 (S2000AF) is defective again after approx. 15 minutes.
• Stuck in standby. Power LED lit . (185702565 tip from SCHAUBLORENZ)
• Switches to standby. Squealing from PSU.
• HT collapses at switch on. After several start-up attempts, HT builds up and R894 (10K) steams.
• One colour fails.
• Stuck in standby. (185702565 tips)
• Right side of the picture is redish and left side is greenish.
• After start-up, channels run through without stopping. Channel stops when pressing P- button on control panel.
• Vertical jitter.
• Blocked power supply.
• The remote control commands are sometimes delayed.
• Switches to standby.
• Vertical IC401 fails
• No reception.
• Switches on, display blinks once.
• Dark screen (when cold).
• Channel 1 appears in display for 5 secs then reverts to standby with green LED flashing on front. (SCHAUBLORENZ - 185702565 information)