66K4627 / SIERRA [TV]

• Raster dented on the side.
• Bridge rectifier blows.
• Vertical jitter. (when contrast high).
• Switches off after aprrox. 1 min.
• Patterning on screen.
• Starts with 12, all channels are noisy. (66K4627 tips)
• Starts up for a short time, then fails.
• The picture's width varies and the convergence jumps constantly.
• Replacement of the IC SAF1031P with SAF1039P.
• Intermittent. Gurgles or vertical lines are present.
• Frame collapse at switch on.
• TXT lines are visible in the upper part of the picture. Approx 3cm away from the upper edge of the picture
• Horizontal shift, no colour.
• No or small frame (voltage reading seems normal).
• VCR time constants: 26 C 568.
• AFT pulls when switch engaged.
• No picture. Sound ok. Contrast is minimal and cannot be adjusted. (66K4627 tips)
• Rolling when contrast or brightness varied.
• Gulps occasionally with a large beam current.
• Clatters, crackles, is noisy and the volume control is blocked.
• No audio.
• Hiccuping.
• Vertical lines in the blank picture operation.
• Dead.
• Intermittent colour after T500 is replaced. (service info for SIERRA -66K4627)
• No sync and no sound. OK on empty channel. (service info for SIERRA -66K4627)
• Power supply ticking, fine if tripler disconnected.
• Low HT.
• Horizontal sync dropout.
• Repeated power supply failure.
• No tuning on some channels.
• Franjas.
• The picture is crooked, E/W correction is not possible.
• Intermittent pincushion distortion.
• Horizontal lines.
• The power supply jumps. The power supply unit is correct.
• East/west fault.
• No vertical deflection.
• Gulps occasionally.
• Width decreases after a few minutes.
• Flyback lines are visible.
• Checking the PSU. (service info for SIERRA -66K4627)
• Connection of a loop system to the TV.
• Picture width is too low, adjustment regulators do not react.
• Gulps at switch off.
• Striations down sides.
• Channel selector V311 no longer available, will be V317. (service info for SIERRA -66K4627)
• Reduced horizontal size.
• No contrast control. (66K4627 tip from SIERRA)
• No E/W, reduced width.
• Intermittent red, green faces.
• Reduced vertical and horizontal size.
• Colour flickers until appliance has warmed up. Stabilizes after a while.
• Vertical linearity fault. Cramp at bottom of picture.
• K9/K11 band switch. (66K4627 tip from SIERRA)
• The picture is blurry and then disappears.
• Outer lines cannot be straightened.
• No function. No hiccuping.
• Almost total vertical collapse.
• Difficulty with grey scale.
• The power supply jumps. No very high voltage. (SIERRA - 66K4627 information)
• Bowing at bottom of picture.
• Noise in picture. (66K4627 tip from SIERRA)
• Occasionally no sound. Sound is too low.
• No contrast.
• Only snow noise is present, no channel number indication.
• Teletext lines on edge of raster (top few lines).
• Only P0 in display. No picture, no sound.
• No sound, dark picture (colour or R/C functions may not work).
• New high voltage tripler.
• North/south correction does not function.
• No colour (horizontal shift). (service info for SIERRA -66K4627)
• Lines above in the picture.
• Afterglow fleck at switch off.
• Red, green or blue picture.
• Power supply repair method. (service info for SIERRA -66K4627)
• Blue raster, no picture.
• Problem of lines on the picture like noise in the picture.
• Convergence is faulty. (SIERRA - 66K4627 information)
• No horizontal hold.
• White horizontal stripes.
• No start-up (intermittently).
• Channels drifting, high band.
• Width, east-west correction and the trapezodal pot(s) do not function.
• Blown chopper.
• Only no. 1 appears on screen, no picture. Only background noise in sound.
• No horizontal scan and hiccupping.
• Luminance lines in the picture, the left hand side is darker.
• Blank raster with flyback lines.
• E/W fault.
• Vertical line in the middle of screen. (66K4627 tip from SIERRA)
• Wine glass shaped picture.
• 1/2 vertical scan (all volts ok).
• The appliance breaks down after 1 min. A transformer or coil may be defective.
• No function, there may be a gurgling sound.
• Goes into safety mode.
• Blows F601.
• Safety test after repair.
• Thick white lines at the top of the picture.
• Dark picture, weak colours.
• Picture and sound have rhythmical interference, even without the station, tuning voltage varies.
• Rolling, no contrast and excessively bright picture.
• Low contrast.
• Tuning drifts.