EURAS System
    EURAS worldwideeuras.com    
EURAS System

WD14SL / WINDSOR [TV 36/37 (34-36) cm picture]

The EURAS repair tip database for professional technicians and service engineers supplies the following faults for WD14SL / WINDSOR.

List of fault symptoms:
  • No start-up from standby. LED is red . No line drive.
  • BU808DFI fails every so often.
  • Intermittently switches off and goes to standby. If switched on again, a digit key has to be pressed on RC.
  • Vertical streaks.
  • No horizontal or vertical deflection.
  • 2-3 cm horizontal stripe in the middle of screen.
  • Dark stripes in picture after a few minutes. Growing thicker and distorting the picture.
  • Line output transistor faulty. (WINDSOR - WD14SL information)
  • Dead (intermittently).
  • 8V missing.
  • TV does not switch on. Standby LED flickers.
  • Picture is instable, horizontal lines from the top to the bottom.
  • No start-up from standby.
  • Vertical deflection reduced to 2-4 cm.
  • Blue picture. Retrace lines. (WD14SL tips)
  • Key-LED lights green for a short time, then becomes red.
  • Vertical lines. Unstable picture.
  • Tripping.
  • Chassis type.
  • Q602 trips repeatedly.
  • Blue screen. Flyback lines.
  • Squealing noise. at start-up.
  • Dark picture.
  • Switches to standby (after warm-up).
  • Switches to protection mode.
  • No start-up. Display flashes .
  • HV output stage (BU808DFI) defective.
  • No funciona. LED en rojo
  • No HV. (WD14SL WINDSOR repair tip)
  • No functions.
  • Horizontal line.
  • Enter service mode.
  • Dead.
  • No picture. Blank raster. Audio OK .
  • R809 and R821 smoking after a few minutes.
  • No start-up. LED is red .
  • Black vertical bar. on the left.
  • Appliance stuck in BG mode.
  • Slow start-up.
  • Green picture. Flyback lines.
  • Blue screen.
  • Picture folds down at the bottom. Linearity and vertical position cannot be adjusted.
  • No function via 12/24V power supply.
  • Unstable picture.
  • PSU pulsates quickly at switch on.
  • Strong continuous chirp from mains transformer with normal operation. Horizontal interference lines (pinch). (WD14SL tips)
  • No start-up.
  • Stuck in standby. (service info for WINDSOR -WD14SL)
  • Does not start up. Standby LED is present at switch-on. LED becomes green for one sec., then it switches off.
  • No picture. Audio OK .
  • No colour.
  • RC is defective.

If WINDSOR WD14SL fails, this information will help you. Here you can only see the symptom list, to access remedies, you must register.

With help of this list a solution is found often when WINDSOR WD14SL fails.


Additionally to repairtips or service information WD14SL is linked to 60 components (IC's and/or transformers) in the Tectra database, through which you can identify electrical compatibilities (crossreferences) in appliances.


Chassis information is available (which chassis is built in into WD14SL ).

EURAS system also knows 327 appliances having the same chassis as WD14SL and can easily list them.

For WD14SL there are 12 compatible appliances known and can be listed.


In the repair discussion pinboard for WD14SL there are 42 replies to questions asked about 16 different repair problems.
With access to EURAS you can all read them or enter your own questions and get help for WD14SL from EURAS technicians or other users.

Do want to see this remedies/cures for repairtips?   Register here for the EURAS System

Already registered? open WD14SL WINDSOR in EURAS

All details on the EURAS System: English | Deutsch | Français | Italiano | Español | Magyarul | Português | Polski | Română | Greek |


Back to EURAS Homepage >> All manufacturers >> WINDSOR tech tips  


(C) EURAS International Ltd.









Last updated: 21. Aug 2008 23:48:19 MET, doccode ISO9002AS168EKA200805C EURASMOP

Responsible for the content: EURAS International GmbH, Eime, Germany. All rights reserved, EURAS database V2.0 (C) 2002-2008. All brand- or productnames are copyrighted by the respective manufacturer of the appliance and are only being used for identification purposes.